diff options
Diffstat (limited to 'dts/upstream/Bindings/arm/tegra/nvidia,tegra186-pmc.yaml')
| -rw-r--r-- | dts/upstream/Bindings/arm/tegra/nvidia,tegra186-pmc.yaml | 198 |
1 files changed, 198 insertions, 0 deletions
diff --git a/dts/upstream/Bindings/arm/tegra/nvidia,tegra186-pmc.yaml b/dts/upstream/Bindings/arm/tegra/nvidia,tegra186-pmc.yaml new file mode 100644 index 00000000000..0faa403f68c --- /dev/null +++ b/dts/upstream/Bindings/arm/tegra/nvidia,tegra186-pmc.yaml @@ -0,0 +1,198 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/tegra/nvidia,tegra186-pmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra Power Management Controller (PMC) + +maintainers: + - Thierry Reding <thierry.reding@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + +properties: + compatible: + enum: + - nvidia,tegra186-pmc + - nvidia,tegra194-pmc + - nvidia,tegra234-pmc + + reg: + minItems: 4 + maxItems: 5 + + reg-names: + minItems: 4 + items: + - const: pmc + - const: wake + - const: aotag + - const: scratch + - const: misc + + interrupt-controller: true + + "#interrupt-cells": + description: Specifies the number of cells needed to encode an + interrupt source. The value must be 2. + const: 2 + + nvidia,invert-interrupt: + description: If present, inverts the PMU interrupt signal. + $ref: /schemas/types.yaml#/definitions/flag + +if: + properties: + compatible: + contains: + const: nvidia,tegra186-pmc +then: + properties: + reg: + maxItems: 4 + + reg-names: + maxItems: 4 +else: + properties: + reg: + minItems: 5 + + reg-names: + minItems: 5 + +patternProperties: + "^[a-z0-9]+-[a-z0-9]+$": + if: + type: object + then: + description: | + These are pad configuration nodes. On Tegra SoCs a pad is a set of + pins which are configured as a group. The pin grouping is a fixed + attribute of the hardware. The PMC can be used to set pad power + state and signaling voltage. A pad can be either in active or + power down mode. The support for power state and signaling voltage + configuration varies depending on the pad in question. 3.3 V and + 1.8 V signaling voltages are supported on pins where software + controllable signaling voltage switching is available. + + Pad configurations are described with pin configuration nodes + which are placed under the pmc node and they are referred to by + the pinctrl client properties. For more information see + + Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + + The following pads are present on Tegra186: + + csia, csib, dsi, mipi-bias, pex-clk-bias, pex-clk3, pex-clk2, + pex-clk1, usb0, usb1, usb2, usb-bias, uart, audio, hsic, dbg, + hdmi-dp0, hdmi-dp1, pex-cntrl, sdmmc2-hv, sdmmc4, cam, dsib, + dsic, dsid, csic, csid, csie, dsif, spi, ufs, dmic-hv, edp, + sdmmc1-hv, sdmmc3-hv, conn, audio-hv, ao-hv + + The following pads are present on Tegra194: + + csia, csib, mipi-bias, pex-clk-bias, pex-clk3, pex-clk2, + pex-clk1, eqos, pex-clk-2-bias, pex-clk-2, dap3, dap5, uart, + pwr-ctl, soc-gpio53, audio, gp-pwm2, gp-pwm3, soc-gpio12, + soc-gpio13, soc-gpio10, uart4, uart5, dbg, hdmi-dp3, hdmi-dp2, + hdmi-dp0, hdmi-dp1, pex-cntrl, pex-ctl2, pex-l0-rst, + pex-l1-rst, sdmmc4, pex-l5-rst, cam, csic, csid, csie, csif, + spi, ufs, csig, csih, edp, sdmmc1-hv, sdmmc3-hv, conn, + audio-hv, ao-hv + + properties: + pins: + $ref: /schemas/types.yaml#/definitions/string + description: Must contain the name of the pad(s) to be + configured. + + low-power-enable: + description: Configure the pad into power down mode. + $ref: /schemas/types.yaml#/definitions/flag + + low-power-disable: + description: Configure the pad into active mode. + $ref: /schemas/types.yaml#/definitions/flag + + power-source: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 or + TEGRA_IO_PAD_VOLTAGE_3V3 to select between signalling + voltages. + + The values are defined in + + include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h + + The power state can be configured on all of the above pads + except for ao-hv. Following pads have software configurable + signaling voltages: sdmmc2-hv, dmic-hv, sdmmc1-hv, sdmmc3-hv, + audio-hv, ao-hv. + + phandle: true + + required: + - pins + + additionalProperties: false + +required: + - compatible + - reg + - reg-names + +additionalProperties: false + +dependencies: + interrupt-controller: ['#interrupt-cells'] + "#interrupt-cells": + required: + - interrupt-controller + +examples: + - | + #include <dt-bindings/clock/tegra186-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/pinctrl/pinctrl-tegra-io-pad.h> + #include <dt-bindings/memory/tegra186-mc.h> + #include <dt-bindings/reset/tegra186-reset.h> + + pmc@c3600000 { + compatible = "nvidia,tegra186-pmc"; + reg = <0x0c360000 0x10000>, + <0x0c370000 0x10000>, + <0x0c380000 0x10000>, + <0x0c390000 0x10000>; + reg-names = "pmc", "wake", "aotag", "scratch"; + nvidia,invert-interrupt; + + sdmmc1_3v3: sdmmc1-3v3 { + pins = "sdmmc1-hv"; + power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>; + }; + + sdmmc1_1v8: sdmmc1-1v8 { + pins = "sdmmc1-hv"; + power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>; + }; + }; + + sdmmc1: mmc@3400000 { + compatible = "nvidia,tegra186-sdhci"; + reg = <0x03400000 0x10000>; + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&bpmp TEGRA186_CLK_SDMMC1>, + <&bpmp TEGRA186_CLK_SDMMC_LEGACY_TM>; + clock-names = "sdhci", "tmclk"; + resets = <&bpmp TEGRA186_RESET_SDMMC1>; + reset-names = "sdhci"; + interconnects = <&mc TEGRA186_MEMORY_CLIENT_SDMMCRA &emc>, + <&mc TEGRA186_MEMORY_CLIENT_SDMMCWA &emc>; + interconnect-names = "dma-mem", "write"; + iommus = <&smmu TEGRA186_SID_SDMMC1>; + pinctrl-names = "sdmmc-3v3", "sdmmc-1v8"; + pinctrl-0 = <&sdmmc1_3v3>; + pinctrl-1 = <&sdmmc1_1v8>; + }; |