aboutsummaryrefslogtreecommitdiff
path: root/dts/upstream/Bindings/sound/st,sta32x.txt
diff options
context:
space:
mode:
Diffstat (limited to 'dts/upstream/Bindings/sound/st,sta32x.txt')
-rw-r--r--dts/upstream/Bindings/sound/st,sta32x.txt101
1 files changed, 101 insertions, 0 deletions
diff --git a/dts/upstream/Bindings/sound/st,sta32x.txt b/dts/upstream/Bindings/sound/st,sta32x.txt
new file mode 100644
index 00000000000..52265fb757c
--- /dev/null
+++ b/dts/upstream/Bindings/sound/st,sta32x.txt
@@ -0,0 +1,101 @@
+STA32X audio CODEC
+
+The driver for this device only supports I2C.
+
+Required properties:
+
+ - compatible: "st,sta32x"
+ - reg: the I2C address of the device for I2C
+ - reset-gpios: a GPIO spec for the reset pin. If specified, it will be
+ deasserted before communication to the codec starts.
+
+ - power-down-gpios: a GPIO spec for the power down pin. If specified,
+ it will be deasserted before communication to the codec
+ starts.
+
+ - Vdda-supply: regulator spec, providing 3.3V
+ - Vdd3-supply: regulator spec, providing 3.3V
+ - Vcc-supply: regulator spec, providing 5V - 26V
+
+Optional properties:
+
+ - clocks, clock-names: Clock specifier for XTI input clock.
+ If specified, the clock will be enabled when the codec is probed,
+ and disabled when it is removed. The 'clock-names' must be set to 'xti'.
+
+ - st,output-conf: number, Selects the output configuration:
+ 0: 2-channel (full-bridge) power, 2-channel data-out
+ 1: 2 (half-bridge). 1 (full-bridge) on-board power
+ 2: 2 Channel (Full-Bridge) Power, 1 Channel FFX
+ 3: 1 Channel Mono-Parallel
+ If parameter is missing, mode 0 will be enabled.
+ This property has to be specified as '/bits/ 8' value.
+
+ - st,ch1-output-mapping: Channel 1 output mapping
+ - st,ch2-output-mapping: Channel 2 output mapping
+ - st,ch3-output-mapping: Channel 3 output mapping
+ 0: Channel 1
+ 1: Channel 2
+ 2: Channel 3
+ If parameter is missing, channel 1 is chosen.
+ This properties have to be specified as '/bits/ 8' values.
+
+ - st,thermal-warning-recover:
+ If present, thermal warning recovery is enabled.
+
+ - st,fault-detect-recovery:
+ If present, fault detect recovery is enabled.
+
+ - st,thermal-warning-adjustment:
+ If present, thermal warning adjustment is enabled.
+
+ - st,fault-detect-recovery:
+ If present, then fault recovery will be enabled.
+
+ - st,drop-compensation-ns: number
+ Only required for "st,ffx-power-output-mode" ==
+ "variable-drop-compensation".
+ Specifies the drop compensation in nanoseconds.
+ The value must be in the range of 0..300, and only
+ multiples of 20 are allowed. Default is 140ns.
+
+ - st,max-power-use-mpcc:
+ If present, then MPCC bits are used for MPC coefficients,
+ otherwise standard MPC coefficients are used.
+
+ - st,max-power-corr:
+ If present, power bridge correction for THD reduction near maximum
+ power output is enabled.
+
+ - st,am-reduction-mode:
+ If present, FFX mode runs in AM reduction mode, otherwise normal
+ FFX mode is used.
+
+ - st,odd-pwm-speed-mode:
+ If present, PWM speed mode run on odd speed mode (341.3 kHz) on all
+ channels. If not present, normal PWM spped mode (384 kHz) will be used.
+
+ - st,invalid-input-detect-mute:
+ If present, automatic invalid input detect mute is enabled.
+
+Example:
+
+codec: sta32x@38 {
+ compatible = "st,sta32x";
+ reg = <0x1c>;
+ clocks = <&clock>;
+ clock-names = "xti";
+ reset-gpios = <&gpio1 19 0>;
+ power-down-gpios = <&gpio1 16 0>;
+ st,output-conf = /bits/ 8 <0x3>; // set output to 2-channel
+ // (full-bridge) power,
+ // 2-channel data-out
+ st,ch1-output-mapping = /bits/ 8 <0>; // set channel 1 output ch 1
+ st,ch2-output-mapping = /bits/ 8 <0>; // set channel 2 output ch 1
+ st,ch3-output-mapping = /bits/ 8 <0>; // set channel 3 output ch 1
+ st,max-power-correction; // enables power bridge
+ // correction for THD reduction
+ // near maximum power output
+ st,invalid-input-detect-mute; // mute if no valid digital
+ // audio signal is provided.
+};