diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/ap325rxa.h | 114 | ||||
| -rw-r--r-- | include/configs/ap_sh4a_4a.h | 102 | ||||
| -rw-r--r-- | include/configs/espt.h | 78 | ||||
| -rw-r--r-- | include/configs/ms7722se.h | 83 | ||||
| -rw-r--r-- | include/configs/ms7750se.h | 65 | ||||
| -rw-r--r-- | include/configs/r0p7734.h | 100 |
6 files changed, 0 insertions, 542 deletions
diff --git a/include/configs/ap325rxa.h b/include/configs/ap325rxa.h deleted file mode 100644 index 901ce4da619..00000000000 --- a/include/configs/ap325rxa.h +++ /dev/null @@ -1,114 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Configuation settings for the Renesas Solutions AP-325RXA board - * - * Copyright (C) 2008 Renesas Solutions Corp. - * Copyright (C) 2008 Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> - */ - -#ifndef __AP325RXA_H -#define __AP325RXA_H - -#define CONFIG_CPU_SH7723 1 - -#define CONFIG_DISPLAY_BOARDINFO -#undef CONFIG_SHOW_BOOT_PROGRESS - -/* MEMORY */ -#define AP325RXA_SDRAM_BASE (0x88000000) -#define AP325RXA_FLASH_BASE_1 (0xA0000000) -#define AP325RXA_FLASH_BANK_SIZE (128 * 1024 * 1024) - -/* undef to save memory */ -/* Monitor Command Prompt */ -/* Buffer size for Console output */ -#define CONFIG_SYS_PBSIZE 256 -/* List of legal baudrate settings for this board */ -#define CONFIG_SYS_BAUDRATE_TABLE { 38400 } - -/* SCIF */ -#define CONFIG_SCIF_A 1 /* SH7723 has SCIF and SCIFA */ -#define CONFIG_CONS_SCIF5 1 - -/* Suppress display of console information at boot */ - -#define CONFIG_SYS_MEMTEST_START (AP325RXA_SDRAM_BASE) -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (60 * 1024 * 1024)) - -/* Enable alternate, more extensive, memory test */ -/* Scratch address used by the alternate memory test */ -#undef CONFIG_SYS_MEMTEST_SCRATCH - -/* Enable temporary baudrate change while serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE - -#define CONFIG_SYS_SDRAM_BASE (AP325RXA_SDRAM_BASE) -/* maybe more, but if so u-boot doesn't know about it... */ -#define CONFIG_SYS_SDRAM_SIZE (128 * 1024 * 1024) -/* default load address for scripts ?!? */ -#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 16 * 1024 * 1024) - -/* Address of u-boot image in Flash (NOT run time address in SDRAM) ?!? */ -#define CONFIG_SYS_MONITOR_BASE (AP325RXA_FLASH_BASE_1) -/* Monitor size */ -#define CONFIG_SYS_MONITOR_LEN (128 * 1024) -/* Size of DRAM reserved for malloc() use */ -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) -#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) - -/* FLASH */ -#undef CONFIG_SYS_FLASH_QUIET_TEST -/* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_EMPTY_INFO -/* Physical start address of Flash memory */ -#define CONFIG_SYS_FLASH_BASE (AP325RXA_FLASH_BASE_1) -/* Max number of sectors on each Flash chip */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 - -/* - * IDE support - */ -#define CONFIG_IDE_RESET 1 -#define CONFIG_SYS_PIO_MODE 1 -#define CONFIG_SYS_IDE_MAXBUS 1 /* IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 -#define CONFIG_SYS_ATA_BASE_ADDR 0xB4180000 -#define CONFIG_SYS_ATA_STRIDE 2 /* 1bit shift */ -#define CONFIG_SYS_ATA_DATA_OFFSET 0x200 /* data reg offset */ -#define CONFIG_SYS_ATA_REG_OFFSET 0x200 /* reg offset */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x210 /* alternate register offset */ -#define CONFIG_IDE_SWAP_IO - -/* if you use all NOR Flash , you change dip-switch. Please see Manual. */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE + (0 * AP325RXA_FLASH_BANK_SIZE)} - -/* Timeout for Flash erase operations (in ms) */ -#define CONFIG_SYS_FLASH_ERASE_TOUT (3 * 1000) -/* Timeout for Flash write operations (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT (3 * 1000) -/* Timeout for Flash set sector lock bit operations (in ms) */ -#define CONFIG_SYS_FLASH_LOCK_TOUT (3 * 1000) -/* Timeout for Flash clear lock bit operations (in ms) */ -#define CONFIG_SYS_FLASH_UNLOCK_TOUT (3 * 1000) - -/* - * Use hardware flash sectors protection instead - * of U-Boot software protection - */ -#undef CONFIG_SYS_DIRECT_FLASH_TFTP - -/* ENV setting */ -#define CONFIG_ENV_OVERWRITE 1 -#define CONFIG_ENV_SECT_SIZE (128 * 1024) -#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) -/* Offset of env Flash sector relative to CONFIG_SYS_FLASH_BASE */ -#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE) - -/* Board Clock */ -#define CONFIG_SYS_CLK_FREQ 33333333 -#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ - -#endif /* __AP325RXA_H */ diff --git a/include/configs/ap_sh4a_4a.h b/include/configs/ap_sh4a_4a.h deleted file mode 100644 index edcc0cbc8ac..00000000000 --- a/include/configs/ap_sh4a_4a.h +++ /dev/null @@ -1,102 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Configuation settings for the Alpha Project AP-SH4A-4A board - * - * Copyright (C) 2012 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> - */ - -#ifndef __AP_SH4A_4A_H -#define __AP_SH4A_4A_H - -#define CONFIG_CPU_SH7734 1 -#define CONFIG_400MHZ_MODE 1 - -#define CONFIG_DISPLAY_BOARDINFO -#undef CONFIG_SHOW_BOOT_PROGRESS - -/* Ether */ -#define CONFIG_SH_ETHER_USE_PORT (0) -#define CONFIG_SH_ETHER_PHY_ADDR (0x0) -#define CONFIG_SH_ETHER_PHY_MODE (PHY_INTERFACE_MODE_GMII) -#define CONFIG_SH_ETHER_SH7734_MII (0x02) /* GMII */ -#define CONFIG_BITBANGMII -#define CONFIG_BITBANGMII_MULTI - -/* undef to save memory */ -/* Monitor Command Prompt */ -/* Buffer size for Console output */ -#define CONFIG_SYS_PBSIZE 256 -/* List of legal baudrate settings for this board */ -#define CONFIG_SYS_BAUDRATE_TABLE { 115200 } - -/* SCIF */ -#define CONFIG_SCIF 1 -#define CONFIG_CONS_SCIF4 1 - -/* Suppress display of console information at boot */ - -/* SDRAM */ -#define CONFIG_SYS_SDRAM_BASE (0x88000000) -#define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024) -#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 16 * 1024 * 1024) - -#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE) -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + CONFIG_SYS_SDRAM_SIZE) -/* Enable alternate, more extensive, memory test */ -/* Scratch address used by the alternate memory test */ -#undef CONFIG_SYS_MEMTEST_SCRATCH - -/* Enable temporary baudrate change while serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE - -/* FLASH */ -#undef CONFIG_SYS_FLASH_QUIET_TEST -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_BASE (0xA0000000) -#define CONFIG_SYS_MAX_FLASH_SECT 512 - -/* if you use all NOR Flash , you change dip-switch. Please see Manual. */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -/* Timeout for Flash erase operations (in ms) */ -#define CONFIG_SYS_FLASH_ERASE_TOUT (3 * 1000) -/* Timeout for Flash write operations (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT (3 * 1000) -/* Timeout for Flash set sector lock bit operations (in ms) */ -#define CONFIG_SYS_FLASH_LOCK_TOUT (3 * 1000) -/* Timeout for Flash clear lock bit operations (in ms) */ -#define CONFIG_SYS_FLASH_UNLOCK_TOUT (3 * 1000) - -/* - * Use hardware flash sectors protection instead - * of U-Boot software protection - */ -#undef CONFIG_SYS_DIRECT_FLASH_TFTP - -/* Address of u-boot image in Flash (NOT run time address in SDRAM) ?!? */ -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE) -/* Monitor size */ -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) -/* Size of DRAM reserved for malloc() use */ -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) -#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) - -/* ENV setting */ -#define CONFIG_ENV_OVERWRITE 1 -#define CONFIG_ENV_SECT_SIZE (128 * 1024) -#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) -/* Offset of env Flash sector relative to CONFIG_SYS_FLASH_BASE */ -#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE) - -/* Board Clock */ -#if defined(CONFIG_400MHZ_MODE) -#define CONFIG_SYS_CLK_FREQ 50000000 -#else -#define CONFIG_SYS_CLK_FREQ 44444444 -#endif -#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ - -#endif /* __AP_SH4A_4A_H */ diff --git a/include/configs/espt.h b/include/configs/espt.h deleted file mode 100644 index 0339de40817..00000000000 --- a/include/configs/espt.h +++ /dev/null @@ -1,78 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Configuation settings for the ESPT-GIGA board - * - * Copyright (C) 2008 Renesas Solutions Corp. - * Copyright (C) 2008 Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> - */ - -#ifndef __ESPT_H -#define __ESPT_H - -#define CONFIG_CPU_SH7763 1 -#define __LITTLE_ENDIAN 1 - -#define CONFIG_ENV_OVERWRITE 1 - -#define CONFIG_DISPLAY_BOARDINFO -#undef CONFIG_SHOW_BOOT_PROGRESS - -/* SCIF */ -#define CONFIG_CONS_SCIF0 1 - -#define CONFIG_SYS_PBSIZE 256 /* Buffer size for Console output */ -#define CONFIG_SYS_BAUDRATE_TABLE { 115200 } /* List of legal baudrate - settings for this board */ - -/* SDRAM */ -#define CONFIG_SYS_SDRAM_BASE (0x8C000000) -#define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024) -#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE) -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (60 * 1024 * 1024)) - -/* Flash(NOR) S29JL064H */ -#define CONFIG_SYS_FLASH_BASE (0xA0000000) -#define CONFIG_SYS_FLASH_CFI_WIDTH (FLASH_CFI_16BIT) -#define CONFIG_SYS_MAX_FLASH_BANKS (1) -#define CONFIG_SYS_MAX_FLASH_SECT (150) - -/* U-Boot setting */ -#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 4 * 1024 * 1024) -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_MONITOR_LEN (128 * 1024) -/* Size of DRAM reserved for malloc() use */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) -#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) - -#undef CONFIG_SYS_FLASH_QUIET_TEST -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -/* Timeout for Flash erase operations (in ms) */ -#define CONFIG_SYS_FLASH_ERASE_TOUT (3 * 1000) -/* Timeout for Flash write operations (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT (3 * 1000) -/* Timeout for Flash set sector lock bit operations (in ms) */ -#define CONFIG_SYS_FLASH_LOCK_TOUT (3 * 1000) -/* Timeout for Flash clear lock bit operations (in ms) */ -#define CONFIG_SYS_FLASH_UNLOCK_TOUT (3 * 1000) -/* Use hardware flash sectors protection instead of U-Boot software protection */ -#undef CONFIG_SYS_DIRECT_FLASH_TFTP -#define CONFIG_ENV_SECT_SIZE (128 * 1024) -#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + (1 * CONFIG_ENV_SECT_SIZE)) -/* Offset of env Flash sector relative to CONFIG_SYS_FLASH_BASE */ -#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE + (2 * CONFIG_ENV_SECT_SIZE)) - -/* Clock */ -#define CONFIG_SYS_CLK_FREQ 66666666 -#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ - -/* Ether */ -#define CONFIG_SH_ETHER_USE_PORT (1) -#define CONFIG_SH_ETHER_PHY_ADDR (0x00) -#define CONFIG_BITBANGMII -#define CONFIG_BITBANGMII_MULTI -#define CONFIG_SH_ETHER_PHY_MODE PHY_INTERFACE_MODE_MII - -#endif /* __SH7763RDP_H */ diff --git a/include/configs/ms7722se.h b/include/configs/ms7722se.h deleted file mode 100644 index 241ba69fa05..00000000000 --- a/include/configs/ms7722se.h +++ /dev/null @@ -1,83 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Configuation settings for the Hitachi Solution Engine 7722 - * - * Copyright (C) 2007 Nobuhiro Iwamatsu <iwamatsu@nigauri.org> - */ - -#ifndef __MS7722SE_H -#define __MS7722SE_H - -#define CONFIG_CPU_SH7722 1 - -#define CONFIG_DISPLAY_BOARDINFO -#undef CONFIG_SHOW_BOOT_PROGRESS - -/* SMC9111 */ -#define CONFIG_SMC91111 -#define CONFIG_SMC91111_BASE (0xB8000000) - -/* MEMORY */ -#define MS7722SE_SDRAM_BASE (0x8C000000) -#define MS7722SE_FLASH_BASE_1 (0xA0000000) -#define MS7722SE_FLASH_BANK_SIZE (8*1024 * 1024) - -#define CONFIG_SYS_PBSIZE 256 /* Buffer size for Console output */ -#define CONFIG_SYS_BAUDRATE_TABLE { 115200 } /* List of legal baudrate settings for this board */ - -/* SCIF */ -#define CONFIG_CONS_SCIF0 1 - -#define CONFIG_SYS_MEMTEST_START (MS7722SE_SDRAM_BASE) -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (60 * 1024 * 1024)) - -#undef CONFIG_SYS_MEMTEST_SCRATCH /* Scratch address used by the alternate memory test */ - -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* Enable temporary baudrate change while serial download */ - -#define CONFIG_SYS_SDRAM_BASE (MS7722SE_SDRAM_BASE) -#define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024) /* maybe more, but if so u-boot doesn't know about it... */ - -#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 4 * 1024 * 1024) /* default load address for scripts ?!? */ - -#define CONFIG_SYS_MONITOR_BASE (MS7722SE_FLASH_BASE_1) /* Address of u-boot image - in Flash (NOT run time address in SDRAM) ?!? */ -#define CONFIG_SYS_MONITOR_LEN (128 * 1024) /* */ -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Size of DRAM reserved for malloc() use */ -#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) - -/* FLASH */ -#undef CONFIG_SYS_FLASH_QUIET_TEST -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ - -#define CONFIG_SYS_FLASH_BASE (MS7722SE_FLASH_BASE_1) /* Physical start address of Flash memory */ - -#define CONFIG_SYS_MAX_FLASH_SECT 150 /* Max number of sectors on each - Flash chip */ - -/* if you use all NOR Flash , you change dip-switch. Please see MS7722SE01 Manual. */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE + (0 * MS7722SE_FLASH_BANK_SIZE), \ - CONFIG_SYS_FLASH_BASE + (1 * MS7722SE_FLASH_BANK_SIZE), \ - } - -#define CONFIG_SYS_FLASH_ERASE_TOUT (3 * 1000) /* Timeout for Flash erase operations (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT (3 * 1000) /* Timeout for Flash write operations (in ms) */ -#define CONFIG_SYS_FLASH_LOCK_TOUT (3 * 1000) /* Timeout for Flash set sector lock bit operations (in ms) */ -#define CONFIG_SYS_FLASH_UNLOCK_TOUT (3 * 1000) /* Timeout for Flash clear lock bit operations (in ms) */ - -#undef CONFIG_SYS_DIRECT_FLASH_TFTP - -#define CONFIG_ENV_OVERWRITE 1 -#define CONFIG_ENV_SECT_SIZE (8 * 1024) -#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + (1 * CONFIG_ENV_SECT_SIZE)) -#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) /* Offset of env Flash sector relative to CONFIG_SYS_FLASH_BASE */ -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE + (2 * CONFIG_ENV_SECT_SIZE)) - -/* Board Clock */ -#define CONFIG_SYS_CLK_FREQ 33333333 -#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ - -#endif /* __MS7722SE_H */ diff --git a/include/configs/ms7750se.h b/include/configs/ms7750se.h deleted file mode 100644 index 949fc04cc8a..00000000000 --- a/include/configs/ms7750se.h +++ /dev/null @@ -1,65 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Configuation settings for the Hitachi Solution Engine 7750 - * - * Copyright (C) 2007 Nobuhiro Iwamatsu <iwamatsu@nigauri.org> - */ - -#ifndef __MS7750SE_H -#define __MS7750SE_H - -#define CONFIG_CPU_SH7750 1 -/* #define CONFIG_CPU_SH7751 1 */ -/* #define CONFIG_CPU_TYPE_R 1 */ -#define __LITTLE_ENDIAN__ 1 - -#define CONFIG_DISPLAY_BOARDINFO - -/* - * Command line configuration. - */ -#define CONFIG_CONS_SCIF1 1 - -#define CONFIG_ENV_OVERWRITE 1 - -/* SDRAM */ -#define CONFIG_SYS_SDRAM_BASE (0x8C000000) -#define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024) - -#define CONFIG_SYS_PBSIZE 256 - -#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE) -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_TEXT_BASE - 0x100000) - -/* NOR Flash */ -/* #define CONFIG_SYS_FLASH_BASE (0xA1000000)*/ -#define CONFIG_SYS_FLASH_BASE (0xA0000000) -#define CONFIG_SYS_MAX_FLASH_BANKS (1) /* Max number of - * Flash memory banks - */ -#define CONFIG_SYS_MAX_FLASH_SECT 142 -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 4 * 1024 * 1024) -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE) /* Address of u-boot image in Flash */ -#define CONFIG_SYS_MONITOR_LEN (128 * 1024) -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Size of DRAM reserved for malloc() use */ - -#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) -#define CONFIG_SYS_RX_ETH_BUFFER (8) - -#undef CONFIG_SYS_FLASH_CFI_BROKEN_TABLE -#undef CONFIG_SYS_FLASH_QUIET_TEST -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ - -#define CONFIG_ENV_SECT_SIZE 0x20000 -#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 - -/* Board Clock */ -#define CONFIG_SYS_CLK_FREQ 33333333 -#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ - -#endif /* __MS7750SE_H */ diff --git a/include/configs/r0p7734.h b/include/configs/r0p7734.h deleted file mode 100644 index 3e4ef763c92..00000000000 --- a/include/configs/r0p7734.h +++ /dev/null @@ -1,100 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Configuation settings for the Renesas Solutions r0p7734 board - * - * Copyright (C) 2010, 2011 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> - */ - -#ifndef __R0P7734_H -#define __R0P7734_H - -#define CONFIG_CPU_SH7734 1 -#define CONFIG_400MHZ_MODE 1 - -#define CONFIG_DISPLAY_BOARDINFO -#undef CONFIG_SHOW_BOOT_PROGRESS - -/* Ether */ -#define CONFIG_SH_ETHER_USE_PORT (0) -#define CONFIG_SH_ETHER_PHY_ADDR (0x0) -#define CONFIG_PHY_SMSC 1 -#define CONFIG_BITBANGMII -#define CONFIG_BITBANGMII_MULTI -#define CONFIG_SH_ETHER_SH7734_MII (0x00) /* MII */ -#define CONFIG_SH_ETHER_PHY_MODE PHY_INTERFACE_MODE_MII - -/* undef to save memory */ -/* List of legal baudrate settings for this board */ -#define CONFIG_SYS_BAUDRATE_TABLE { 115200 } - -/* SCIF */ -#define CONFIG_SCIF 1 -#define CONFIG_CONS_SCIF3 1 - -/* Suppress display of console information at boot */ - -/* SDRAM */ -#define CONFIG_SYS_SDRAM_BASE (0x88000000) -#define CONFIG_SYS_SDRAM_SIZE (128 * 1024 * 1024) -#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 16 * 1024 * 1024) - -#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE) -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 100 * 1024 * 1024) -/* Enable alternate, more extensive, memory test */ -/* Scratch address used by the alternate memory test */ -#undef CONFIG_SYS_MEMTEST_SCRATCH - -/* Enable temporary baudrate change while serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE - -/* FLASH */ -#undef CONFIG_SYS_FLASH_QUIET_TEST -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_BASE (0xA0000000) -#define CONFIG_SYS_MAX_FLASH_SECT 512 - -/* if you use all NOR Flash , you change dip-switch. Please see Manual. */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -/* Timeout for Flash erase operations (in ms) */ -#define CONFIG_SYS_FLASH_ERASE_TOUT (3 * 1000) -/* Timeout for Flash write operations (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT (3 * 1000) -/* Timeout for Flash set sector lock bit operations (in ms) */ -#define CONFIG_SYS_FLASH_LOCK_TOUT (3 * 1000) -/* Timeout for Flash clear lock bit operations (in ms) */ -#define CONFIG_SYS_FLASH_UNLOCK_TOUT (3 * 1000) - -/* - * Use hardware flash sectors protection instead - * of U-Boot software protection - */ -#undef CONFIG_SYS_DIRECT_FLASH_TFTP - -/* Address of u-boot image in Flash (NOT run time address in SDRAM) ?!? */ -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE) -/* Monitor size */ -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) -/* Size of DRAM reserved for malloc() use */ -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) -#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) - -/* ENV setting */ -#define CONFIG_ENV_OVERWRITE 1 -#define CONFIG_ENV_SECT_SIZE (128 * 1024) -#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) -/* Offset of env Flash sector relative to CONFIG_SYS_FLASH_BASE */ -#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE) - -/* Board Clock */ -#if defined(CONFIG_400MHZ_MODE) -#define CONFIG_SYS_CLK_FREQ 50000000 -#else -#define CONFIG_SYS_CLK_FREQ 44444444 -#endif -#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ - -#endif /* __R0P7734_H */ |