| Age | Commit message (Collapse) | Author |
|---|
|
Sync from Linux commit a188339ca5a3 ("Linux 5.2-rc1")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
This patch add documentation for TPL build and flashing steps
for rk3399 boards.
Add full boot log for future reference.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Enable TPL for NanoPC T4, NanoPI M4 boards.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Enable TPL for OrangePI rk3399 board.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add initial support for Rock PI 4 board.
Specification
- Rockchip RK3399
- LPDDR4
- eMMC
- SD card slot
- RTL8211E 1Gbps
- HDMI In/Out, DP, MIPI DSI/CSI
- PCIe M.2
- USB 2.0, USB-3.0
- USB C Type
Commit details of rk3399-rock-pi-4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: add ROCK Pi 4 DTS support"
(sha1: 1b5715c602fda7b812af0e190eddcce2812e5417)
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add initial support for Rockpro64 board.
Specification
- Rockchip RK3399
- 2/4GB Dual-Channel LPDDR3
- SD card slot
- eMMC socket
- 128Mb SPI Flash
- Gigabit ethernet
- PCIe 4X slot
- WiFI/BT module socket
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-rockpro64.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: rockpro64 dts add usb regulator"
(sha1: 6db644c79c8d45d73b56bc389aebd85fc3679beb)
'Akash' has sent an initial patch before, so I keep him as board
maintainer and I'm co-maintainer based on our conversation.
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add initial support for Nanopi NEO4 board.
Specification
- Rockchip RK3399
- 1GB DDR3-1866
- SD card slot
- eMMC Socket
- RTL8211E 1Gbps
- AP6212 WiFI/BT
- HDMI In/Out, DP, MIPI CSI
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 5V/3A
Commit details of rk3399-nanopi-neo4.dts sync from Linux:
"arm64: dts: rockchip: Add Nanopi NEO4 initial support"
(sha1: 092470b537f19788d957aed12d835a179b606014)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
This patch cleans up make_fit_atf.py in the following way:
* Fix all issues reported by pylint
* Move copyright notice from file-to-generate to script
* Fix of-by-one bugs in loadables property
* Remove commented-out (dead) code.
Besides the bugfix no intended changes.
Tested on RK3399-Q7 with TF-A v2.1 as BL31.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
This patch adds the rate for UART1 and UART3 the same way
as already implemented for UART0 and UART2.
This is required for boards, which have their console output
on these UARTs.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The RK3399 SPL does not use a pinctrl driver to setup the UART pins.
Instead it works based on config macros, which set the base address
of the actual UART block.
Currently the RK3399 SPL support UART0 and UART2.
This patch adds UART3 in the same way as UART0.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
This patch adds the missing GRF bit definitions for UART3 on the RK3399.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Puma SoMs have a 4 MB SPI NOR flash.
Therefore we can move the environment to the end of the flash
(4 MiB - 16 kiB) in order to not overlap with SPL.
Reported-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
- Audio support
|
|
- Remove various dead code from DaVinci
- FAT fixes
|
|
Both the SPL_LOAD_FIT and SPL_LOAD_FIT_FULL have the same description.
Adjust the description to make it clear which one is which.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
|
|
Contrary to fat12/16, fat32 can have root directory at any location
and its size can be expanded.
Without this patch, root directory won't grow properly and so we will
eventually fail to add files under root directory. Please note that this
can happen even if you delete many files as deleted directory entries
are not reclaimed but just marked as "deleted" under the current
implementation.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
When a long name directory entry is created, multiple directory entries
may be occupied across a directory cluster boundary. Since only one
directory cluster is cached in a directory iterator, a first cluster must
be written back to device before switching over a second cluster.
Without this patch, some added files may be lost even if you don't see
any failures on write operation.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
With the commit below, fat now correctly handles a file read under
a non-cluster-aligned root directory of fat12/16.
Write operation should be fixed in the same manner.
Fixes: commit 9b18358dc05d ("fs: fat: fix reading non-cluster-aligned
root directory")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Anssi Hannula <anssi.hannula@bitwise.fi>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Compiling the display command leads to an error
undefined reference to `display_set'
No implementation of display_set() exists in U-Boot.
Eliminate the `display` command as well as the accompanying files.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
For bcm7445 and bcm7260, this patch enables CONFIG_DM_MMC and updates
the bcmstb SDHCI driver to use the new driver model. This allows
removal of SDHCI configuration handling from bcmstb.c, and eliminates
a board removal compile warning.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The first memory location of ${dtbaddr} may be still valid after a warm
restart of the machine and 'fdt addr ${dtbaddr}' doesn't recognize that
the cfgscript didn't run properly and fallback mechanism with copying
the internal fdt ${fdtcontroladdr} to ${dtbaddr} doesn't catch this.
To get sure that we have proper failsafe behaviour we simply zero the
first memory location of ${dtbaddr} for getting sure that the fdt is
invalid if cfgscript didn't run.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
fat_itr_root() allocates fatbuf so we free it on the exit path, if
the function fails we should not free it, check the return value
and skip freeing if the function fails.
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
File names may not contain control characters (< 0x20).
Simplify the coding.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- defconfig updates to remove the DM-move build warnings for helios4 and
controlcenterdc (Mario & Stefan)
|
|
Several drivers used by the ControlCenterDC board were converted to DM
upstream. But the board had not been using these drivers yet.
Update the board's config file to reflect these changes and use the DM
version of these drivers. No further device tree updates are necessary,
since the devices in question are already present in the device tree.
This especially fixes the three compile warnings about CONFIG_DM_MMC,
CONFIG_DM_USB, and CONFIG_AHCI for the ControlCenterDC board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch enables CONFIG_BLK and CONFIG_DM_MMC on helios4 to remove
these compile warnings:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dennis Gilmore <dgilmore@redhat.com>
|
|
- Gen3 PCIe driver + enablement on Salvator-X platforms.
- Gen3 recovery SPL used to reload ATF/OpTee/U-Boot instead of minimon.
- SDHI HS400 fixes ported from latest BSP and datasheet.
|
|
- SoCFPGA PL310 cleanup + A10 fix, A10 DT cleanup, DW GPIO fix.
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Move the main symbol for Freescale Fman Ethernet controller option to
Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and
rename the SPIFLASH one to follow the same format as all of the others.
To do this fully we need to migrate CONFIG_QC, do so.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Pull request for UEFI sub-system for v2019.07-rc3 (3)
Several bug fixes for the UEFI sub-system are provided.
The SetTime() boottime service is implemented.
|
|
- mtmips: network stability fixes for gardena-smart-gateway
- mtmips: enable CONFIG_USE_PREBOOT and CONFIG_CMD_WDT
|
|
Enable sound output. With this, 'sound play 1000 400' emits a simple beep.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Add a short note about how to boot U-Boot on Nyan-big using tegrarcm.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Add a sound driver for tegra devices. This connects the audio hub, I2S
controller and audio codec to allow sound output.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Add a driver which supports transmitting digital sound to an audio codec.
This uses fixed parameters as a device-tree binding is not currently
defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Add a driver for the audio hub. This is modelled as a misc device which
supports writing audio data from I2S.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
This function enables a peripheral clock and then immediately sets its
divider. Add a delay to allow the clock to settle first. This matches the
delay in other places which do a similar thing.
Without this, the I2S device on Nyan does not init properly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
The first clock type appears to have and incorrect setting for out of the
mux outputs. It should be CLK_M, not OSC. Fix it and its only user.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
If a variable already exists, efi_set_variable() should not change
the variable's attributes. This patch enforces it.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
The current efi_st_variable() doesn't support EFI_VARIABLE_APPEND_WRITE
attiribute for now, and so should return an error.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Fix typos is commit message.
Add TODO comment.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
