aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2021-10-12rtc: ds1307: Handle oscillator-stop bit correctlyMark Tomlinson
The DS1307 driver was originally based on the DS1337 driver. However, the functionality of the clock set/get functions has diverged. In the original DS1337 driver, the set/get functions did the following: 1) Setting the clock ensured the oscillator was enabled. 2) Getting the clock checked and reset the oscillator-stop flag. The DS1307 does not have an oscillator-stop flag, but the driver tried (incorrectly) to emulate this by ensuring the oscillator was running. It really makes no sense to start a stopped clock without setting it. This patch makes the DS1307 driver behave like the original DS1337 driver again. For the DS1307 itself, this is just a removal of code, since there is no oscillator-fail bit to check or reset, and the clock is started when it is set. Since the DS1307 driver can now also be used for the DS1337 and DS1340 which do have this bit, add code to handle the oscillator-stop bit in the same was the original DS1337 driver did -- i.e. report that the oscillator had stopped and clear the flag. This means that setting the date using the date command (which does both a get and a set) will now clear the oscillator-stop flag in addition to setting and starting the clock. The old-style (non-DM) code has not been updated and will be removed in a future patch. Note that this older code does not support the DS1337, as there is a separate driver for this. Also note that the original (DM) code used the wrong control-register address for the DS1337. Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
2021-10-12fs: fat: check for buffer size before reading blocksRicardo Salveti
This patch optimizes the commit mentioned below by avoiding running a set of commands which are useless in the case when size < mydata->sect_size and sect_count would be 0. Fixes: 5b3ddb17ba ("fs/fat/fat.c: Do not perform zero block reads if there are no blocks left") Signed-off-by: Ricardo Salveti <ricardo@foundries.io> Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io> Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
2021-10-12mtd: rawnand: Add Macronix raw NAND controller driverZhengxun Li
Add a driver for Macronix raw NAND controller. This patch referred from linux mxic_nand.c. The difference from the linux version is described here. 1. In order to adapt to the uboot nand framework, add function binding (cmdfunc, read_byte, read_buf, write_buf). 2. Added parsing command format to use hardware correctly. 3. Remove the incompatible functions of Uboot. Signed-off-by: Zhengxun Li <zhengxunli@mxic.com.tw>
2021-10-12fastboot: fix partition name truncation in environment lookupMatthias Schiffer
strlcat() need to be passed the full buffer length. The incorrect call caused truncation of partition names for fastboot_raw_partition_... and fastboot_partition_alias_... env lookup to much less than PART_NAME_LEN. Fixes: 69a752983171 ("fastboot: Fix possible buffer overrun") Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Reviewed-by: Sean Anderson <seanga2@gmail.com>
2021-10-12Merge tag 'u-boot-stm32-20211012' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-stm - Disable ATAGS for STM32 MCU and MPU boards - Disable bi_boot_params for STM32 MCU and MPU boards - Update stm32-usbphyc node management - Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards - Convert some USB config flags to Kconfig for various boards - Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board - Remove specific CONFIG_STV0991 flags - Remove unused CONFIG_USER_LOWLEVEL_INIT flag - Add ofdata_to_platdata() callback for stm32_spi driver - Update for stm32f7_i2c driver - Remove gpio_hog_probe_all() from STM32 MP1 board - Fix bind command Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-12Merge tag 'u-boot-at91-2022.01-b' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-at91 Second set of u-boot-at91 features for the 2022.01 cycle: This small feature set adds the support for PWM driver for the sama5d2 SoC. It also adds a node in the DT for this SoC.
2021-10-12Merge https://source.denx.de/u-boot/custodians/u-boot-sunxiTom Rini
The bulk of it is Samuel's DM_I2C rework, which removes the nasty I2C deprecation warnings for most 32-bit boards. It also includes some smaller refactorings that pave the way for more changes, mostly driven by needing to support the Allwinner RISC-V SoC later on. Board wise we gain support for the FriendlyARM NanoPi R1S H5 router board and official Pinetab support. Build-tested for all 160 sunxi boards, and boot tested on a A64, A20, H3, H6, and H616 board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
2021-10-12test/py: Add usb gadget binding testPatrice Chotard
Add a specific usb gadget binding test which check that binding a driver without compatible string is working as expected. the command "bind /usb@1 usb_ether" should give the following "dm tree" command output: [...] usb 0 [ ] usb_sandbox |-- usb@1 usb_hub 0 [ ] usb_hub | |-- hub usb_emul 0 [ ] usb_sandbox_hub | | `-- hub-emul usb_emul 1 [ ] usb_sandbox_flash | | |-- flash-stick@0 usb_emul 2 [ ] usb_sandbox_flash | | |-- flash-stick@1 usb_emul 3 [ ] usb_sandbox_flash | | |-- flash-stick@2 usb_emul 4 [ ] usb_sandbox_keyb | | `-- keyb@3 eth 4 [ ] usb_ether | `-- usb@1 [...] Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Marek Vasut <marex@denx.de> Cc: Herbert Poetzl <herbert@13thfloor.at> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-10-12configs: sandbox: add USB_ETHER and GADGET_DOWNLOAD gadget supportPatrice Chotard
This is needed for new gadget binding test. Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Marek Vasut <marex@denx.de> Cc: Herbert Poetzl <herbert@13thfloor.at> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-10-12usb: sandbox: Add gadget callbacksPatrice Chotard
Add usb_gadget_handle_interrupts(), usb_gadget_register_driver() and usb_gadget_unregister_driver() to be able to test binding usb gadget. Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Marek Vasut <marex@denx.de> Cc: Herbert Poetzl <herbert@13thfloor.at> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-10-12usb: gadget: Add bcdDevice for the DWC2 USB Gadget ControllerPatrice Chotard
Add an entry in usb_gadget_controller_number() for the DWC2 gadget controller. It is used to bind the USB Ethernet driver. Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reported-by: Herbert Poetzl <herbert@13thfloor.at> Cc: Marek Vasut <marex@denx.de> Cc: Herbert Poetzl <herbert@13thfloor.at>
2021-10-12cmd: bind: Fix driver binding on a devicePatrice Chotard
Fix a regression brings by commit 84f8e36f03fa ("cmd: bind: allow to bind driver with driver data") As example, the following bind command doesn't work: bind /soc/usb-otg@49000000 usb_ether As usb_ether driver has no compatible string, it can't be find by lists_bind_fdt(). In bind_by_node_path(), which called lists_bind_fdt(), the driver entry is known, pass it to lists_bind_fdt() to force the driver entry selection. For this, add a new parameter struct *driver to lists_bind_fdt(). Fix also all lists_bind_fdt() callers. Fixes: 84f8e36f03fa ("cmd: bind: allow to bind driver with driver data") Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reported-by: Herbert Poetzl <herbert@13thfloor.at> Cc: Marek Vasut <marex@denx.de> Cc: Herbert Poetzl <herbert@13thfloor.at> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-10-12ARM: dts: sama5d2: Add pwm0 definitionDan Sneddon
Add node for the PWM0 on the SAMA5D2 SoC. Signed-off-by: Dan Sneddon <dan.sneddon@microchip.com>
2021-10-12dt-bindings: pwm: pwm-at91: Add PWM bindings for A5D2Dan Sneddon
Document the bindings needed for the PWM device on the SAMA5D2. Signed-off-by: Dan Sneddon <dan.sneddon@microchip.com>
2021-10-12pwm: Add PWM driver for SAMA5D2Dan Sneddon
Add support for the PWM found on the SAMA5D2 family of devices. Signed-off-by: Dan Sneddon <dan.sneddon@microchip.com>
2021-10-12sunxi: Enable DM_I2C for all sunxi boardsSamuel Holland
Now that the last users of legacy I2C (outside of SPL) have been resolved, we can enable DM_I2C at the sunxi architecture level. Reviewed-by: Heiko Schocher <hs@denx.de> Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12sunxi: video: Convert panel I2C to use DM_I2CSamuel Holland
Two displays supported by the sunxi display driver (each one used by a single board) require initialization over I2C. Both previously used i2c_soft; replace this with the i2c-gpio instance that already exists in those boards' device trees (sun5i-a13-utoo-p66 and sun6i-a31-colombus). Since the i2c-gpio nodes are not referenced by any other node in the device trees (the device trees have no panel node), the I2C bus is selected by its node name. This panel initialization code was the only i2c_soft user, so the i2c_soft GPIO setup code can be removed now as well. Reviewed-by: Heiko Schocher <hs@denx.de> Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12sunxi: pmic_bus: Use the DM PMIC interface when possibleSamuel Holland
The pmic_bus functions are used in both SPL (for regulator setup) and U-Boot proper (for regulator setup, SID access, GPIO, and poweroff). Currently, pmic_bus conflicts with DM_I2C because it uses the legacy I2C interface. This commit makes pmic_bus dual-compatible with either the legacy I2C functions or the newly-added PMIC_AXP driver (which uses DM_I2C). In turn, this allows platforms to start transitioning to DM_I2C in U-Boot proper, without breaking boards that still depend on the legacy I2C interface for other reasons. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12sunxi: pmic_bus: Clean up preprocessor conditionsSamuel Holland
Instead of using the SoC symbols to decide the bus type, use whichever bus driver is actually enabled. This allows collapsing all of the AXP2xx and AXP8xx variants into one "else" case. It also has the advantage of falling back to I2C when the other bus drivers are disabled; this works because all of the PMICs support I2C in addition to other interfaces. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12i2c: Add a DM_I2C driver for the sun8i RSB controllerSamuel Holland
This bus controller is used to communicate with an X-Powers AXP PMIC. Currently, various drivers access PMIC registers through a platform- specific non-DM "pmic_bus" interface, which depends on the legacy I2C framework. In order to convert those drivers to use DM_PMIC, this bus needs a DM_I2C driver. Refactor the rsb functions to take the base address as a parameter, and implement both the existing interface (which is still needed in SPL) and the DM_I2C interface on top of them. The register for switching between I2C/P2WI/RSB mode is the same across all PMIC variants, so move that to the common header. There are only a couple of pairs of hardware/runtime addresses used across all PMIC variants. So far the code expected only the "primary" pair, but some PMICs like the AXP305 and AXP805 use the secondary pair, so add support for that to the DM driver as well. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12i2c: Add a DM_I2C driver for the sun6i P2WI controllerSamuel Holland
This bus controller is used to communicate with an X-Powers AXP PMIC. Currently, various drivers access PMIC registers through a platform- specific non-DM "pmic_bus" interface, which depends on the legacy I2C framework. In order to convert those drivers to use DM_PMIC, this bus needs a DM_I2C driver. Refactor the p2wi functions to take the base address as a parameter, and implement both the existing interface (which is still needed in SPL) and the DM_I2C interface on top of them. The register for switching between I2C/P2WI/RSB mode is the same across all PMIC variants. Move that to the common header, so it can be used by both interface implementations. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12sunxi: pmic_bus: Fix Kconfig dependenciesSamuel Holland
AXP_PMIC_BUS enables communication with a specific AXP PMIC at a PMIC-dependent I2C/P2WI/RSB bus address. It is automatically selected as a dependency of the PMIC driver. It should not be selectable by the user when no PMIC is chosen. AXP_GPIO uses the pmic_bus functions, and also depends on a specific PMIC header to pick up register definitions. Both of these changes have no impact on any existing configs, since the code does not compile if the dependencies are not met. Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12sunxi: Select SUN8I_RSB more carefullySamuel Holland
SUN8I_RSB should not be selected by MACH_SUN8I, because the hardware is not present in half of those SoCs (H3/H5, R40, and V3s). Move the selection to the SoCs where the hardware actually exists. As it currently stands, selecting that option also requires using it in some way, which is not the case for one A80 board. Since we have only three A80 boards in total, we select it their via their defconfigs. Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Samuel Holland <samuel@sholland.org> [Andre: fixing up Sunchip_CX-A99 build] Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12sunxi: Only initialize legacy I2C when enabledSamuel Holland
CONFIG_SPL_I2C is the wrong symbol to use here. It is the top-level Kconfig symbol (not specific to either legacy or DM I2C), whereas the i2c_init() function is specific to legacy I2C. This change fixes a build failure when enabling SPL_I2C but not SPL_SYS_I2C_LEGACY. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12power: pmic: Add a driver for X-Powers AXP PMICsSamuel Holland
These PMICs provide some combination of battery charger, fuel gauge, GPIOs, regulators, and VBUS routing. These functions are represented as child nodes in the device tree. Add the minimal driver needed to probe these child devices and provide the DM_PMIC ops. Enable the driver by default for SoCs that normally pair with a PMIC. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12power: pmic: Consistently depend on SPL_DM_PMICSamuel Holland
Now that there is a separate symbol to enable DM_PMIC in SPL, update the the SPL-specific driver symbols to depend on this new option. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12power: pmic: Consistently depend on DM_PMICSamuel Holland
Kconfig symbols for two PMIC drivers (PMIC_AS3722 and DM_PMIC_MC34708) were missing a dependency on DM_PMIC. To fix this inconsistency, and to keep it from happening again, wrap the driver section with "if DM_PMIC" instead of using a "depends on DM_PMIC" clause for each driver. Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11Merge branch '2021-10-11-TI-platform-updates'Tom Rini
- Assorted TI platform updates
2021-10-11arm: dts: Update IOT2050 device tree filesJan Kiszka
This fixes the usage of the USB 3.0-capable port under U-Boot as USB 2.0-only port. Original patch by Chao Zeng. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
2021-10-11board: siemens: iot2050: Adjust to changes in DT and configurationJan Kiszka
Account for the changes done between merge proposal and the final merge. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2021-10-11ARM: omap3_logic: Cleanup usage of MUX_VALAdam Ford
The macro called MUX_VAL generates a writel instruction with semicolon at the end. This table was written to use semicolons, however one was missed: MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) /* GPIO_4 */ Since the extra semicolon is unnecessary with the use of the macro, remove all of them, and cleanup whitespace. Reviewed-by: Wolfgang Denk <wd@denx.de> Suggested-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Adam Ford <aford173@gmail.com>
2021-10-11clk: ti: add am33xx/am43xx spread spectrum clock supportDario Binacchi
The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs. As reported by the TI spruh73x/spruhl7x RM, SSC is only supported for the DISP/LCD and MPU PLLs on am33xx/am43xx. SSC is not supported for DDR, PER, and CORE PLLs. Calculating the required values and setting the registers accordingly was taken from the set_mpu_spreadspectrum routine contained in the arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project. In locked condition, DPLL output clock = CLKINP *[M/N]. In case of SSC enabled, the reference manual explains that there is a restriction of range of M values. Since the clk_ti_am3_dpll_round_rate() attempts to select the minimum possible N, the value of M obtained is not guaranteed to be within the range required. With the new "ti,min-div" parameter it is possible to increase N and consequently M to satisfy the constraint imposed by SSC. Link: https://lore.kernel.org/r/20210606202253.31649-6-dariobin@libero.it Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-10-11ARM: dts: am43xx-clocks: add spread spectrum supportDario Binacchi
Registers for adjusting the spread spectrum clocking (SSC) have been added. As reported by the TI spruhl7x RM, SSC is supported only for LCD and MPU PLLs, but the PRCM_CM_SSC_DELTAMSTEP_DPLL_XXX and PRCM_CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field in the PRCM_CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE, MPU, DDR, PER, DISP, EXTDEV). Link: https://lore.kernel.org/r/20210606202253.31649-5-dariobin@libero.it Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-10-11ARM: dts: am33xx-clocks: add spread spectrum supportDario Binacchi
Registers for adjusting the spread spectrum clocking (SSC) have been added. As reported by the TI spruh73x RM, SSC is supported only for LCD and MPU PLLs, but the CM_SSC_DELTAMSTEP_DPLL_XXX and CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field in the CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE, MPU, DDR, PER, DISP). Link: https://lore.kernel.org/r/20210606202253.31649-4-dariobin@libero.it Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-10-11configs: omap3x_logic: Enable LTO on more LogicPD OMAP3 boardsAdam Ford
There are five omap3 based boards from LogicPD. Two of them have added LTO support. Add the remaining three to use LTO. Signed-off-by: Adam Ford <aford173@gmail.com>
2021-10-11sunxi: Add support for FriendlyARM NanoPi R1S H5Chukun Pan
This adds support for the NanoPi R1S H5 board. Allwinner H5 SoC 512MB DDR3 RAM 10/100/1000M Ethernet x 2 RTL8189ETV WiFi 802.11b/g/n USB 2.0 host port (A) MicroSD Slot Reset button Serial Debug Port WAN - LAN - SYS LED The dts file is taken from Linux 5.14 tag. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11clk: sunxi: Add drivers for A31 and H6 PRCM CCUsSamuel Holland
Add a driver so the clocks/resets for these peripherals (especially I2C, RSB, and UART) can be enabled using the normal uclass methods. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11clk: sunxi: Add support for I2C gates/resetsSamuel Holland
Currently, the I2C clocks are configured in the sunxi board code. Add the I2C clocks to the DM clock driver so they can be enabled from the DM I2C driver using the normal uclass methods. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11sunxi: gpio: Remove bank-specific size macrosSamuel Holland
Since the beginning, all banks have had space for 32 pins, even when not all pins were implemented. Let's use a single constant for the GPIO bank size here, like the GPIO driver is already doing. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11sunxi: gpio: Remove name_to_gpio macroSamuel Holland
This clarifies which callers must be updated to complete the DM_GPIO conversion. The only remaining caller of name_to_gpio in generic code is inside the !DM_GPIO block in cmd/gpio.c. DM_GPIO is always selected on sunxi, so that code cannot be reached. And after this commit, there are only two remaining implementations of name_to_gpio. Signed-off-by: Samuel Holland <samuel@sholland.org> Acked-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11sunxi: Clean up inclusions of asm/arch/gpio.hSamuel Holland
As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will remove the asm/arch/gpio.h header. In preparation, clean up the various files that include it. Some files did not contain any GPIO code at all, so this header was completely unused. A few files contained only legacy platform-specific GPIO code for setting up pin muxes. They were left unchanged, as that code will be completely removed by the DM_PINCTRL migration. The remaining files contain some combination of DM_GPIO and legacy GPIO code. For those, switch to including asm/gpio.h (if it wasn't included already). Right now, this header provides both sets of functions, because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the right header to include once the DM_GPIO migration is complete and GPIO_EXTRA_HEADER is no longer needed. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11pinephone_defconfig: add support for early-boot status LEDArnaud Ferraris
This commit enables the green status LED (PD18/GPIO 114) on boot in the SPL, in order to provide visual feedback that the PinePhone is booting. Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Samuel Holland <samuel@sholland.org> Tested-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11board: sunxi: enable status LED earlyArnaud Ferraris
For some systems, such as the PinePhone, there is no way for the end user to make sure the system is indeed booting before the boot script is executed, which takes several seconds. Therefore, it can be useful to provide early visual feedback as soon as possible. In order achieve this goal, this patch initializes the status LED (if configured) in the SPL. Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com> Reviewed-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11gpio: sunxi: Remove the sunxi_name_to_gpio_bank functionSamuel Holland
The only caller of this function was the MMC pinmux code, which used it to parse a string given from a Kconfig symbol. As the Kconfig symbol has been converted to a Boolean, this function is no longer needed. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11sunxi: Simplify MMC pinmux selectionSamuel Holland
Only one board, Yones Toptech BD1078, actually uses a non-default MMC pinmux. All other uses of these symbols select the default value or an invalid value. To simplify things, remove support for the unused pinmux options, and convert the remaining option to a Boolean. This allows the pinmux to be chosen by the preprocessor, instead of having the code parse a string at runtime (for a build-time option!). Not only does this reduce code size, but it also allows this Kconfig option to be used in a table-driven DM pinctrl driver. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11clk: sunxi: Move header out of arch directorySamuel Holland
The CCU header is only used by the DM drivers, not any platform code. Its current location adds an artificial dependency on CONFIG_ARM and ARCH_SUNXI, which will be problematic when adding the CCU driver for a RISC-V sunxi platform. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11configs: add PineTab defconfigArnaud Ferraris
The PineTab device-tree is already in u-boot, this commit adds the corresponding defconfig, based on pinephone_defconfig. Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-09Merge tag 'video-20211009' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-video - add 30bpp support (EFI, simplefb, vidconsole) - fix video console name in CONSOLE_MUX Kconfig help - move mxsfb driver config option to Kconfig - remove unused mx3fb driver # gpg verification failed.
2021-10-09video: move MXS to KconfigAnatolij Gustschin
Move CONFIG_VIDEO_MXS from board headers to Kconfig and drop it from obsolete cfb_console driver. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-10-09video: remove not used mx3fb driverAnatolij Gustschin
i.MX31 support was removed, and the non dm-video driver is obsolete and not used. Remove it. Signed-off-by: Anatolij Gustschin <agust@denx.de>
generated by cgit v1.2.3 (git 2.39.1) at 2024-09-21 21:37:08 +0000