aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-08-27mmc: sti_sdhci: Fix sdhci_setup_cfg() call.Patrice Chotard
host->mmc, host->mmc->dev and host->mmc->priv must be set before calling sdhci_setup_cfg() to avoid hang during mmc initialization. Thanks to commit 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") which put this issue into evidence. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-27mmc: stm32_sdmmc2: Increase SDMMC_BUSYD0END_TIMEOUT_USPatrice Chotard
Increase SDMMC_BUSYD0END_TIMEOUT_US from 1s to 2s to avoid timeout error during blocks erase on some sdcard Issue seen on Kingston 16GB : Device: STM32 SDMMC2 Manufacturer ID: 27 OEM: 5048 Name: SD16G Bus Speed: 50000000 Mode: SD High Speed (50MHz) card capabilities: widths [4, 1] modes [SD Legacy, SD High Speed (50MHz)] host capabilities: widths [4, 1] modes [MMC legacy, SD Legacy, MMC High Speed (26MHz), SD High Speed (50MHz), MMC High Speed (52MHz)] Rd Block Len: 512 SD version 3.0 High Capacity: Yes Capacity: 14.5 GiB Bus Width: 4-bit Erase Group Size: 512 Bytes Issue reproduced with following command: STM32MP> mmc erase 0 100000 MMC erase: dev # 0, block # 0, count 1048576 ... mmc erase failed 16384 blocks erased: ERROR By setting SDMMC_BUSYD0END_TIMEOUT_US at 2 seconds and by adding time measurement in stm32_sdmmc2_end_cmd() as shown below: +start = get_timer(0); /* Polling status register */ ret = readl_poll_timeout(priv->base + SDMMC_STA, status, status & mask, SDMMC_BUSYD0END_TIMEOUT_US); +printf("time = %ld ms\n", get_timer(start)); We get the following trace: STM32MP> mmc erase 0 100000 MMC erase: dev # 0, block # 0, count 1048576 ... time = 17 ms time = 1 ms time = 1025 ms time = 54 ms time = 56 ms time = 1021 ms time = 57 ms time = 56 ms time = 1020 ms time = 53 ms time = 57 ms time = 1021 ms time = 53 ms time = 57 ms time = 1313 ms time = 54 ms time = 56 ms time = 1026 ms time = 54 ms time = 56 ms time = 1036 ms time = 54 ms time = 56 ms time = 1028 ms time = 53 ms time = 56 ms time = 1027 ms time = 54 ms time = 56 ms time = 1024 ms time = 54 ms time = 56 ms time = 1020 ms time = 54 ms time = 57 ms time = 1023 ms time = 54 ms time = 56 ms time = 1033 ms time = 53 ms time = 57 ms .... time = 53 ms time = 57 ms time = 1021 ms time = 56 ms time = 56 ms time = 1026 ms time = 54 ms time = 56 ms 1048576 blocks erased: OK We see that 1 second timeout is not enough, we also see one measurement up to 1313 ms. Set the timeout to 2 second to keep a security margin. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-08-26Prepare v2019.10-rc3Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-26Merge branch '2019-08-26-master-imports'Tom Rini
- Assorted minor bugfixes
2019-08-26tools: remove easylogo and include/video_logo.hHeinrich Schuchardt
include/video_logo.h once was created via the tool easylogo and than used in cpu/mpc8xx/video.c to display Tux. video_logo.h has been replaced by include/linux_logo.h and is not needed anymore. Delete the include and the tool, Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-08-26ARM: am3517-evm: Disable CONFIG_USB_EHCI_OMAP in SPLAdam Ford
Found accidentally in omap3_logic, CONFIG_USB_EHCI_OMAP adds some code size to SPL, so this patch disables it on the am3517-evm to reduce the code a bit since it's tight for space. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-26ARM: da850evm_direct_nor: Enable DM_GPIOAdam Ford
The SPI and NAND variants enable DM_GPIO, so this patch enables DM_GPIO for the NOR / XIP version of the da850-evm. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-26ARM: da850evm_nand: Enable EthernetAdam Ford
The NAND configuration has had the ethernet missing, so this patch enables the on-board ethernet interface. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-26Kconfig: Varios: Fix more SPL, TPL dependenciesAdam Ford
Several options are presenting themselves on a various boards where the options are clearly not used. (ie, SPL/TPL options when SPL or TPL are not defined) This patch is not attempting to be a complete list of items, but more like low hanging fruit. In some instances, I wasn't sure of DM was required, so I simply made them SPL or TPL. This patch attempts to reduce some of the menuconfig noise by defining dependencies so they don't appear when not used. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-26MAINTAINERS,board/siemens: update maintainerSamuel Egli
Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Acked-by: Roger Meier <r.meier@siemens.com> Cc: Heiko Schocher <hs@denx.de>
2019-08-26mailmap: Update mail addressRicardo Ribalda Delgado
Update my email address from gmail to my domain. Signed-off-by: Ricardo Ribalda Delgado <ricardo@ribalda.com>
2019-08-26board: ti: am43xx_evm_usbboot: Enable DM for USB, fix SPL build errorsSuniel Mahesh
To address the following warning message: ===================== WARNING ====================== This board does not use CONFIG_DM_USB. Please update the board to use CONFIG_DM_USB before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/MIGRATION.txt for more info. ==================================================== CONFIG_DM_USB is enabled, this resulted in SPL build errors: drivers/built-in.o: In function 'xhci_dwc3_probe': u-boot/drivers/usb/host/xhci-dwc3.c:155: undefined reference to 'usb_get_dr_mode' scripts/Makefile.spl:404: recipe for target 'spl/u-boot-spl' failed make[1]: *** [spl/u-boot-spl] Error 1 Makefile:1721: recipe for target 'spl/u-boot-spl' failed make: *** [spl/u-boot-spl] Error 2 Enabling usb common library and usb ethernet drivers in SPL does the job. Target was compile tested, build was clean. Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
2019-08-26nvme: Fix PRP Offset InvalidAaron Williams
When large writes take place I saw a Samsung EVO 970+ return a status value of 0x13, PRP Offset Invalid. I tracked this down to the improper handling of PRP entries. The blocks the PRP entries are placed in cannot cross a page boundary and thus should be allocated on page boundaries. This is how the Linux kernel driver works. With this patch, the PRP pool is allocated on a page boundary and other than the very first allocation, the pool size is a multiple of the page size. Each page can hold (4096 / 8) - 1 entries since the last entry must point to the next page in the pool. Signed-off-by: Aaron Williams <awilliams@marvell.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-08-26cmd: pci: Adjust display of digits for 64bit address and sizeKunihiko Hayashi
The command "pci bar" and "pci region" display the address and size in 16 characters including "0x", so the command can only display 14 hexadecimal digits if the number of digits in the address and size is less than 14. ID Base Size Width Type ---------------------------------------------------------- 0 0x00000020000000 0x00000000100000 64 MEM Prefetchable 1 0xffff000080000000 0x00000000100000 64 MEM Prefetchable The 64-bit address and size should be displayed in 18(= 16+2) digits, so this patch adjusts them. Cc: Yehuda Yitschak <yehuday@marvell.com> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-08-26ARM: omap3_logic: Fix SPL boot failure when EHCI enabledAdam Ford
Some of the USB code is still being built into SPL even when the SPL menu options have it explicitly disabled for SPL. Unit there is a better solution, This patch undefines CONFIG_USB_EHCI_OMAP when building SPL which reduces the code and lets the board boot again. Fixes: 25e4ff45b17d ("ARM: omap3_logic: Enable OMAP EHCI support for SOM-LV Boards") Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-26cmd: gpio: remove redundant assignmentHeinrich Schuchardt
The assigned value NULL is overwritten before being used. Remove the assignment. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-08-26vexpress/aemv8a: drop CONFIG_ARMV8_SWITCH_TO_EL1Sudeep Holla
To support KVM, we need to drop at EL2 and not EL1 before we boot Linux kernel. This causes issues on platform with VHE and secondaries booting at EL2 via TF-A PSCI CPU_ON call. Cc: Ryan Harkin <ryan.harkin@linaro.org> Cc: Liviu Dudau <liviu.dudau@foss.arm.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: David Feng <fenghua@phytium.com.cn> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-08-26ARM: vexpress_*_defconfig: replace earlyprintk with earlyconSudeep Holla
earlyprintk no longer works on arm64 platforms. Replace it with earlycon which works fine. Cc: Ryan Harkin <ryan.harkin@linaro.org> Cc: Liviu Dudau <liviu.dudau@foss.arm.com> Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2019-08-26fat: FAT filesystem premature release of info struct.Martin Vystrčil
File was found on specified location. Info about file was read, but then immediately destroyed using 'free' call. As a result file size was set to 0, hence fat process didn't read any data. Premature 'free' call removed. Resources are freed right before function return. File is read correctly. Signed-off-by: Martin Vystrcil <martin.vystrcil@m-linux.cz>
2019-08-26dm: scsi: Scan the actual number of portsPark, Aiden
The scsi_scan_dev() is looping over the number of uc_plat->max_id. The number of actual ports a AHCI controller has can be greater than max_id. Update uc_plat->max_id to make SCSI scan all detected ports. Signed-off-by: Aiden Park <aiden.park@intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-08-26ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin muxAdam Ford
When the pinmux configuration was added, it was accidentally placed into the omap3_pmx_wkup node when it should have been placed into the omap3_pmx_core. This error was accidentally propagated to U-Boot by me when I blindly copied the device tree from Linux. This patch moves the i2c2_pins and i2c3_pins to the correct node which should eliminate i2c bus errors and timeouts due to the fact the bootloader uses the save device tree that no longer properly assigns these pins. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-26board_f: reserve noncached space below malloc areaVikas Manocha
Noncached area at present is being initialized to random space after malloc area. It works in most the cases as it goes to stack area & stack is not overwriting it being far from it. Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2019-08-26arm: ti: Fix regression in distro boot for mmcNuno Gonçalves
When devnum was changed to a local variable in distro_bootcmd we ran into a problem on TI platforms (confirmed on Beaglebone) as we had been using 'setenv devnum' there as well and it needs to match the other usage. Fixes: 13dd6665ed18 ("distro: not taint environment variables if possible") [trini: Review other platforms, re-word commit message] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-26Merge https://gitlab.denx.de/u-boot/custodians/u-boot-riscvTom Rini
- Support SPL and OpenSBI (FW_DYNAMIC firmware) boot. - Fix qemu kconfig build warning.
2019-08-26Merge branch '2019-08-24-master-imports'Tom Rini
- Migrate SYS_SPI_U_BOOT_OFFS, SYS_NAND_USE_FLASH_BBT and ARCH_CPU_INIT to Kconfig
2019-08-26riscv: qemu: Fix kconfig build warningBin Meng
When 'make qemu-riscv64_defconfig', there is a build warning: board/emulation/qemu-riscv/Kconfig:24: warning: config symbol defined without type Fix it by specifying the config symbol type to 'hex'. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
2019-08-26doc: update QEMU RISC-V documentationLukas Auer
The available defconfigs for RISC-V QEMU have changed. We now have configurations to compile U-Boot to run in supervisor mode and for U-Boot SPL. Update the QEMU RISC-V documentation to reflect these changes. Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com>
2019-08-26riscv: qemu: add SPL configurationLukas Auer
Add two new configurations (qemu-riscv{32,64}_spl_defconfig) with SPL enabled for RISC-V QEMU. QEMU does not require SPL to run U-Boot. The configurations are meant to help the development of SPL on RISC-V. The configurations enable RAM as the only SPL boot device. Images must be loaded at address 0x80200000. In the default boot flow, U-Boot SPL starts in machine mode, loads the OpenSBI FW_DYNAMIC firmware and U-Boot proper from the supplied FIT image, and starts OpenSBI. U-Boot proper is then started in supervisor mode by OpenSBI. Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com>
2019-08-26riscv: set default FIT generator script and build target for SPL buildsLukas Auer
Now that we have a generic FIT generator script for RISC-V, set it as the default. To also build the FIT image by default, set the default build target to "u-boot.itb" if CONFIG_SPL_LOAD_FIT is enabled. Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com>
2019-08-26riscv: add a generic FIT generator scriptLukas Auer
Add a generic FIT generator script for RISC-V to generate images containing U-Boot, OpenSBI FW_DYNAMIC firmware, and optionally one or more device trees. The location of the OpenSBI firmware binary can be specified with the OPENSBI environment variable. By default, it is assumed to be "fw_dynamic.bin", located in the U-Boot top-level. Device trees are passed as arguments to the generator script. A separate configuration entry is created for each device tree. The load addresses of U-Boot and OpenSBI are parsed from the U-Boot configuration. They can be overwritten with the UBOOT_LOAD_ADDR and OPENSBI_LOAD_ADDR environment variables. The script is based on the i.MX (arch/arm/mach-imx/mkimage_fit_atf.sh) and Allwinner sunxi (board/sunxi/mksunxi_fit_atf.sh) FIT generator scripts. Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com>
2019-08-26riscv: support SPL stack and global data relocationLukas Auer
To support relocation of the stack and global data on RISC-V, the secondary harts must be notified of the change using IPIs. We can reuse the hart relocation code for this purpose. It uses global data to store the new stack pointer and global data pointer for the secondary harts. This means that we cannot update the global data pointer of the main hart in spl_relocate_stack_gd(), because the secondary harts have not yet been relocated at this point. It is updated after the secondary harts have been notified. Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com>
2019-08-26riscv: add SPL supportLukas Auer
U-Boot SPL on the generic RISC-V CPU supports two boot flows, directly jumping to the image and via OpenSBI firmware. In the first case, both U-Boot SPL and proper must be compiled to run in the same privilege mode. Using OpenSBI firmware, U-Boot SPL must be compiled for machine mode and U-Boot proper for supervisor mode. To be able to use SPL, boards have to provide a supported SPL boot device. Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com>
2019-08-26spl: support booting via RISC-V OpenSBILukas Auer
RISC-V OpenSBI is an open-source implementation of the RISC-V Supervisor Binary Interface (SBI) specification. It is required by Linux and U-Boot running in supervisor mode. This patch adds support for booting via the OpenSBI FW_DYNAMIC firmware. It supports OpenSBI version 0.4 and higher. In this configuration, U-Boot SPL starts in machine mode. After loading OpenSBI and U-Boot proper, it will start OpenSBI. All necessary parameters are generated by U-Boot SPL and are passed to OpenSBI. U-Boot proper is started in supervisor mode by OpenSBI. Support for OpenSBI is enabled with CONFIG_SPL_OPENSBI. An additional configuration entry, CONFIG_SPL_OPENSBI_LOAD_ADDR, is used to specify the load address of the OpenSBI firmware binary. It is not used directly in U-Boot and instead is intended to make the value available to scripts such as FIT configuration generators. The header file include/opensbi.h is based on header files from the OpenSBI project. They are recent, as of commit bae54f764570 ("firmware: Add fw_dynamic firmware"). Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com>
2019-08-26riscv: add run mode configuration for SPLLukas Auer
U-Boot SPL can be run in a different privilege mode from U-Boot proper. Add new configuration entries for SPL to allow the run mode to be configured independently of U-Boot proper. Extend all uses of the CONFIG_RISCV_SMODE and CONFIG_RISCV_MMODE configuration symbols to also cover the SPL equivalents. Ensure that files compatible with only one privilege mode are not included in builds targeting an incompatible privilege mode. Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com>
2019-08-26spl: fit: use U-Boot device tree when FIT image has no device treeLukas Auer
As part of the SPL FIT boot flow, the device tree is appended to U-Boot proper. The device tree is used to record information on the loadables to make them available to the SPL framework and U-Boot proper. Depending on the U-Boot device tree provider, the FIT image might not include a device tree. Information on the loadables is missing in this case. When booting via firmware bundled with the FIT image, U-Boot SPL loads the firmware binary and U-Boot proper before starting the firmware. The firmware, in turn, is responsible for starting U-Boot proper. Information on the memory location of the U-Boot proper loadable must be available to the SPL framework so that it can be passed to the firmware binary. To support this use case when no device tree is found in the FIT image, fall back to the U-Boot device tree in this situation. At the same time, update the comment to remove the note that the destination address must be aligned to ARCH_DMA_MINALIGN. Alignment is only required as an intermediate step when reading external data. This is automatically handled by spl_fit_append_fdt(). After reading the external data, it is copied to the specified address, which does not have to be aligned to ARCH_DMA_MINALIGN. Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com>
2019-08-26Makefile: support building SPL FIT images without device treesLukas Auer
When building a U-Boot FIT image, the device trees specified by the board are unconditionally built for inclusion in the FIT image. However, not all device tree providers, such as CONFIG_OF_PRIOR_STAGE, require a device tree to be built and bundled with the U-Boot binary. They rely on other mechanisms to provide the device tree to U-Boot. Compilation on boards with these device tree providers fails, because they do not specify a device tree. Change the makefile rules to conditionally build the device trees if CONFIG_OF_SEPARATE, CONFIG_OF_EMBED, or CONFIG_OF_HOSTFILE is selected as device tree provider. Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com>
2019-08-26fdtdec: make CONFIG_OF_PRIOR_STAGE available in SPLLukas Auer
The current preprocessor logic prevents CONFIG_OF_PRIOR_STAGE from being used in U-Boot SPL. Change the logic to also make it available in U-Boot SPL. Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com>
2019-08-25Convert CONFIG_SYS_SPI_U_BOOT_OFFS to KconfigHannes Schmelzer
This converts the following to Kconfig: CONFIG_SYS_SPI_U_BOOT_OFFS Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> [trini: Expose this for SPL_SPI_SUNXI for now] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-25moveconfig: prepare moving CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig step 4Hannes Schmelzer
the x530 board needs conversion of SPL_SPI_LOAD to Kconfig first Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
2019-08-25moveconfig: prepare moving CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig step 3Hannes Schmelzer
Exact two boards are referencing CONFIG_SYS_SPI_U_BOOT_OFFS to another define, we replace this manually with the value for having a clean run of moveconfig.py afterwards. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-08-25moveconfig: prepare moving CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig step 2Hannes Schmelzer
some boards have common headers for several individual build-targets where CONFIG_SYS_SPI_U_BOOT_OFFS is defined even it is not needed (only needed if CONFIG_SPL_SPI_LOAD is defined also). Take this define here under '#ifdef CONFIG_SPL_SPI_LOAD' for having a clean run of moveconfig.py Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-08-25moveconfig: prepare moving CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig step 1Hannes Schmelzer
Some boards have coded this offset with formula or bitshifts in their board-config. Manually convert these things into hex-values to be able using moveconfig.py afterwards. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-08-25mtd: nand: raw: Move CONFIG_SYS_NAND_USE_FLASH_BBT to KconfigStefan Roese
Convert CONFIG_SYS_NAND_USE_FLASH_BBT to Kconfig, update defconfigs, headers and whitelist. Please note that this symbol already was used in Kconfig (imply in CONFIG_NAND_ATMEL) which did not work, since this symbol was not available in Kconfig. This changes now with this patch and all boards with CONFIG_NAND_ATMEL will have BBT enabled. Which is what I also need on my GARDENA AT91SAM based board. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Eugen Hristev <eugen.hristev@microchip.com> Cc: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Gregory CLEMENT <gregory.clement@bootlin.com> [trini: Rework such that the configs are unchanged to start with] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-25Convert CONFIG_ARCH_CPU_INIT to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_ARCH_CPU_INIT Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Tested-by: Felix Brack <fb@ltec.ch>
2019-08-25configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-24Merge tag 'u-boot-rockchip-20190823' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - remove rk3288 fennec board - remove SPL raw image support for Rockchip SoCs - add common misc_init_r() for ethaddr from cpuid - enable USB HOST support for rk3328 - unify code for finding a valid gpt in part driver
2019-08-24Merge branch '2019-08-23-master-imports'Tom Rini
- Migrate CONFIG_MX_CYCLIC, CONFIG_FSL_USDHC and CONFIG_MXS_GPIO to Kconfig - Fix some SPL/TPL and ARM64 dependencies
2019-08-23Convert CONFIG_MX_CYCLIC to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MX_CYCLIC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: David Lechner <david@lechnology.com>
2019-08-23Convert CONFIG_FSL_USDHC to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_FSL_USDHC Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-23Kconfigs: Various: Fix some SPL, TPL and ARM64 dependenciesAdam Ford
Several options are presenting themselves on a various boards where the options are clearly not used. (ie, arm64 options on arm9, or SPL/TPL options when SPL or TPL are not defined) This patch is not attempting to be a complete list of items, but more like low hanging fruit. This patch attempts to reduce some of the menuconfig noise by defining dependencies so they don't appear when not used. Signed-off-by: Adam Ford <aford173@gmail.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-11 11:41:43 +0000