| Age | Commit message (Collapse) | Author |
|---|
|
Our earlier change broke the generation of SPI images, by excluding the
2K used for header0 from the size-calculation.
This commit makes sure that these are included before calculating the
required total size (including the padding from the 2K-from-every-4K
conversion).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
To include the ability to load from an SPI flash in SPL, it's not
sufficient to define SPL_SPI_SUPPORT and SPL_SPI_FLASH_SUPPORT via
Kconfig... so we conditionally define SPL_SPI_LOAD if SPI support
is already enabled for SPL via Kconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The existing Rockchip SPI (rk_spi.c) driver also matches the hardware
block found in the RK3399. This has been confirmed both with SPI NOR
flashes and general SPI transfers on the RK3399-Q7 for SPI1 and SPI5.
This change adds the 'rockchip,rk3399-spi' string to its compatible
list to allow reuse of the existing driver.
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
This commit adds support for the pin-configuration of the SPI5
controller of the RK3399 through the following changes:
* grf_rk3399.h: adds definition for configuring the SPI5 pins
in the GPIO2C group
* periph.h: defines PERIPH_ID_SPI3 through PERIPH_ID_SPI5
* pinctrl_rk3399.c: adds the reverse-mapping from the IRQ# to
PERIPH_ID_SPI5; dispatches PERIPH_ID_SPI3
through SPI5 to the appropriate pin-config
function; implements the pin-configuration
for PERIPH_ID_SPI5 using the GPIO2C group
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The baudrate in rkspi was calculated by using an integer division
(which implicitly discarded any fractional result), then rounding to
an even number and finally clamping to 0xfffe using a bitwise AND
operator. This introduced two issues:
1) for very small baudrates (overflowing the 0xfffe range), the
bitwise-AND generates rather random-looking (wildly varying)
actual output bitrates
2) for higher baudrates, the calculation tends to 'err towards a
higher baudrate' with the actual error increasing as the dividers
become very small. E.g., with a 99MHz input clock, a request
for a 20MBit baudrate (99/20 = 4.95), a 24.75 MBit would be use
(which amounts to a 23.75% error)... for a 34 MBit request this
would be an actual outbout of 49.5 Mbit (i.e. a 45% error).
This change rewrites the divider selection (i.e. baudrate calculation)
by making sure that
a) for the normal case: the largest representable baudrate below the
requested rate will be chosen;
b) for the denormal case (i.e. when the divider can no longer be
represented), the lowest representable baudrate is chosen.
Even though the denormal case (b) may be of little concern in real
world applications (even with a 198MHz input clock, this will only
happen at below approx. 3kHz/3kBit), our board-verification team kept
complaining.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
|
|
The original clock/bitrate selection code for the rk_spi driver was a
bit limited, as it always selected a 99MHz input clock rate (which
would allow for a maximum bitrate of 49.5MBit/s), but returned -EINVAL
if a bitrate higher than 48MHz was requested.
To give us better control over the bitrate (i.e. add more operating
points, especially at "higher" bitrate---such as above 9MBit/s), we
try to choose 4x the maximum frequency (clamped to 50MBit) from the
DTS instead of 99MHz... for most use-cases this will yield a frequency
of 198MHz, but is flexible to go beyond this in future configurations.
This also rewrites the check to allow frequencies of up to half the
SPI module rate as bitrates and then clamps to whatever the DTS allows
as a maximum (board-specific) frequency and does away with the -EINVAL
when trying to select a bitrate (for cases that exceeded the hard
limit) and instead consistently clamps to the lower of the hard limit,
the soft limit for the SPI bus (from the DTS) or the soft limit for
the SPI slave device.
This replaces
"rockchip: spi: rk_spi: select 198MHz input to the SPI module for the RK3399"
"rockchip: spi: rk_spi: improve clocking code for the RK3399"
from earlier versions of this series.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
i2c/spi_set_rate
For the RK3399, i2c_set_rate (and by extension: our spi_set_rate,
which had been mindlessly following the template of the i2c_set_rate
implementation) miscalculates the rate returned due to a off-by-one
error resulting from the following sequence of events:
1. calculates 'src_div := src_freq / target_freq'
2. stores 'src_div - 1' into the register (the actual divider applied
in hardware is biased by adding 1)
3. returns the result of the DIV_RATE(src_freq, src_div) macro, which
expects the (decremented) divider from the hardware-register and
implictly adds 1 (i.e. 'DIV_RATE(freq, div) := freq / (div + 1)')
This can be observed with the SPI driver, which sets a rate of 99MHz
based on the GPLL frequency of 594MHz: the hardware generates a clock
of 99MHz (src_div is 6, the bitfield in the register correctly reads 5),
but reports a frequency of 84MHz (594 / 7) on return.
To fix, we have two options:
* either we bias (i.e. "DIV_RATE(GPLL, src_div - 1)"), which doesn't
make for a particularily nice read
* we simply call the i2c/spi_get_rate function (introducing additional
overhead for the additional register-read), which reads the divider
from the register and then passes it through the DIV_RATE macro
Given that this code is not time-critical, the more readable solution
(i.e. calling the appropriate get_rate function) is implemented in this
change.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
This change adds support for configuring the module clocks for SPI1 and
SPI5 from the 594MHz GPLL.
Note that the driver (rk_spi.c) always sets this to 99MHz, but the
implemented functionality is more general and will also support
different clock configurations.
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Modify Makefile for rockchip video driver according to Kconfig, so that
source code will not be compiled if not needed.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
1. add Kconfig for rockchip video driver, so that video port can be
selected as needed.
2. move VIDEO_ROCKCHIP option to new Kconfig for concision.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Drop indenting in Kconfig:
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
RK3399 device memory region is 0xf8000000~0xffffffff.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The genunie bus clock is sclk_x for eMMC/SDMMC, add support for it.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The genunie bus clock is sclk_x for eMMC/SDMMC/SDIO, add support for
it.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The genunie bus clock is sclk_x for eMMC/SDMMC/SDIO, add support for
it.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The genunie bus clock is sclk_x for eMMC/SDIO, add support for it.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
As you know, biu_clk is used for AMBA AHB/APB interface, ciu_clk is
used for communication between host and card devices. The real bus clock
is ciu, so let's rectify it.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Add support for rk3328 package header in mkimage tool.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Use regulators_enable_boot_on() instead of init regulators one by one,
the interface can init all the regulators with regulator-boot-on property.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
With the addition of Kconfig now having CONFIG_TWL4030_POWER and
with that being the default when OMAP34XX is selected, this
is no longer needed in include/configs and can be removed from the
whitelist.
This has only been tested on logic PD DM3730 using ti_omap3_common.h
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
As requested, I added the CONFIG_TWL4030_POWER to Kconfig and made it
the implied default when selecting OMAP34XX as a platform.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
With the addition of twl4030_power_off(), let's allow the 'poweroff' command
to run this function when CONFIG_CMD_POWEROFF is enabled.
Tested on a DM3730 with twl4030 PMIC.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
This patch also removes all the excessive code for NS16550 intiailization
as the device tree can do that now. This also adds DM_I2C and DM_MMC
since the overlying drivers have the built-in support already. The
corresponding include/config/omap3_logic.h also reduced in size
due to the new device tree support.
Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
Retain Auto-detect ability between SOM-LV and Torpedo
Split this off from the device sub submissions
|
|
Previous commit has this combined with SOM-LV. This commit has only
the Torpedo Device Tree.
The device trees were sync'd with 4.9.y stable with two changes:
disable mmc2 and stdout-path = &uart1. Both of those two changes
will be submitted to the linux-omap list
Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
Split device tree from other board
|
|
This adds the device tree. Previous commit added both boards at the
same time.
Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
Split the SOM-LV from Torpedo
|
|
Some OMAP3 devices support an SMSC ethernet PHY connected to the GPMC bus.
This copies this device tree from Linux 4.9.y stable
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Many OMAP3 boards use a TWL4030 PMIC. This brings in the related
device tree information for common TWL4030 and TWL4030 with OMAP3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
New i2c_read, i2c_write and i2c_probe functions, tested on OMAP4
(4430/60/70), OMAP5 (5430) and AM335X (3359) were added in 960187ffa125(
"ARM: OMAP: I2C: New read, write and probe functions") but not tested
on OMAP3. This patch will allow the updated drivers using device tree and
DM_I2C to operate on OMAP3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add device tree support to allow for CONFIG_OF_CONTROL in OMAP3630 boards.
DM3730 can use this same device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add device tree support to allow for CONFIG_OF_CONTROL in OMAP3 boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
This patch changes the way DM_MMC calculates offset to the base register of
MMC. Previously this was through an #ifdef but that wasn't necessary for OMAP3.
This patch will now add in the offset to the base address based on the
.compatible flags.
Signed-off-by: Adam Ford <aford173@gmail.com>
V2: Remove ifdef completely and reference offset from the omap_hsmmc_ids table.
V1: Change ifdef to ignore OMAP3
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
In some boards like the Raspberry Pi the initial bootloader will pass
a DT to the kernel. When using U-Boot as such kernel, the board code in
U-Boot should be able to provide U-Boot with this, already assembled
device tree blob.
This patch introduces a new config option CONFIG_OF_BOARD to use instead
of CONFIG_OF_EMBED or CONFIG_OF_SEPARATE which will initialize the DT
from a board-specific funtion instead of bundling one with U-Boot or as
a separated file. This allows boards like the Raspberry Pi to reuse the
device tree passed from the bootcode.bin and start.elf firmware
files, including the run-time selected device tree overlays.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Paolo Pisati <p.pisati@gmail.com>
|
|
The board code should all move into msg.c for consistency. Add a TODO for
this.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Adjust the video driver to work with driver model and move over existing
baords. There is no need to keep the old code.
We can also drop setting of CONFIG_FB_ADDR since driver model doesn't have
this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
Allow this to work with CONFIG_DM_VIDEO enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
Adjust this function so that we can convert it to support CONFIG_DM_VIDEO
without a lot of code duplication.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
Add a function to set the video parameters to the msg handler and remove
it from the video driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
Add a function to get the video size to the msg handler and remove it from
the video driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
We should not use an embedded device tree on a production board. There
does not seem to be any reason for it in commit 7670909. So drop this.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Convert the bcm2835 SDHCI driver over to support CONFIG_DM_MMC and move
all boards over. There is no need to keep the old code since there are no
other users.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this code into the new message handler file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The bcm283x chips provide a way for the ARM core to communicate with the
graphics processor, which is in charge of many things. This is handled by
way of a message prototcol.
At present the code for sending message (and receiving a reply) is spread
around U-Boot, primarily in the board file. This means that sending a
message from a driver requires duplicating the code.
Create a new message implementation with a function to support powering on
a subsystem as a starting point.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Enable CONFIG_DM_ETH so that driver model is used for the USB Ethernet
device.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Start using driver model for USB on the Raspberry Pi. The dwc2 supports
this now so this is just a config change.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This is not needed now that serial uses driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We can rely on the device tree to provide this information.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
A common use of memmove() can be handled by memcpy(). Also memcpy()
includes an optimisation for large sizes: it copies a word at a time. So
we can get a speed-up by calling memcpy() to handle our move in this case.
Update memmove() to call memcpy() if the destination is before the source.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
On further review this returns the wrong packet length from the driver.
It may not be noticed since protocols will take care of it. Fix it by
subtracting the header length from the packet length returned.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
|
|
|
