aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2022-03-18sandbox: test: Tidy up spl_test_load() callsSimon Glass
Use the new sandbox_find_next_phase() function, which does what is needed here. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-18sandbox: Slow down the LCD sync rateSimon Glass
There is seldom a need to refresh at 100Hz and it uses a lot of CPU. Reduce the rate to 10Hz which seems to be adequate. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-18sandbox: Open host file for read-only access if neededSimon Glass
Some files cannot be written but read-only access is still useful for tests. Add a fallback to read-only access when needed. This is useful in CI when opening a large data file provided by docker, where read/write access would result in copying the file, thus needing a lot of extra disk space. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-18sandbox: Add the handoff header for splSimon Glass
This defines a function declared in handoff.h so add the header. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-18sandbox: Show a message when writing out the ram bufferSimon Glass
If state is not being written, but RAM is, we should still show a message, so it is clear that this is happening. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-18binman: Include also subnodes in generator nodesJan Kiszka
This allows to prefill fdt and config nodes with hash and signature subnodes. It's just important to place the child nodes last so that hashes do not come before the data - would be disliked by mkimage. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-03-18tools: binman: main.py: add build-sandbox in sys.pathPhilippe Reynes
Adds build-sandbox in sys.path to look for libfdt, otherwise py_test can't use binman. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-03-18binman: Complete elf test coverageSimon Glass
Add coverage for the new elf functions needed for the event_dump.py script. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-16Merge tag 'xilinx-for-v2022.07-rc1' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-microblaze into next Xilinx changes for v2022.07-rc1 microblaze: - Add support for reserved memory xilinx: - Update FRU code with MAC reading zynqmp: - Remove double AMS setting - DT updates (mostly for SOMs) - Add support for zcu106 rev 1.0 zynq: - Update nand binding nand: - Aligned zynq_nand to upstream DT binding net: - Add support for ethernet-phy-id mmc: - Workaround CD in zynq_sdhci driver also for ZynqMP - Add support for dynamic/run-time SD config for SOMs gpio: - Add driver for slg7xl45106 firmware: - Add support for dynamic SD config power-domain: - Update zynqmp driver with the latest firmware video: - Add skeleton driver for DP and DPDMA i2c: - Fix i2c to work with QEMU pinctrl: - Add driver for zynqmp pinctrl driver
2022-03-16arm64: zynqmp: Add pinctrl emmc description to SM-K26Michal Simek
Production SOM has emmc on it and make sense to describe pin description to be able use EMMC if it is not configured via psu_init. (Still some regs are not handled but this is one step in that direction) Signed-off-by: Michal Simek <michal.simek@xilinx.com> Link: https://lore.kernel.org/r/3545a0f08d342de98efc82b78f5725eda091555a.1647267969.git.michal.simek@xilinx.com
2022-03-16Merge branch '2022-03-15-add-erofs-support' into nextTom Rini
- Add erofs support
2022-03-15test/py: Add tests for the erofsHuang Jianan
Add Python scripts to test 'ls' and 'load' commands, as well as test related filesystem functions. Signed-off-by: Huang Jianan <jnhuang95@gmail.com>
2022-03-15fs/erofs: add filesystem commandsHuang Jianan
Add 'ls' and 'load' commands. Signed-off-by: Huang Jianan <jnhuang95@gmail.com>
2022-03-15fs/erofs: add lz4 decompression supportHuang Jianan
Support EROFS lz4 compressed files. Signed-off-by: Huang Jianan <jnhuang95@gmail.com>
2022-03-15lib/lz4: update LZ4 decompressor moduleHuang Jianan
Update the LZ4 compression module based on LZ4 v1.8.3 in order to use the newest LZ4_decompress_safe_partial() which can now decode exactly the nb of bytes requested. Signed-off-by: Huang Jianan <jnhuang95@gmail.com>
2022-03-15fs/erofs: add erofs filesystem supportHuang Jianan
This patch mainly deals with uncompressed files. Signed-off-by: Huang Jianan <jnhuang95@gmail.com>
2022-03-15CI, Docker: Update to latest focal tagTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-14Merge tag 'v2022.04-rc4' into nextTom Rini
Prepare v2022.04-rc4
2022-03-14Prepare v2022.04-rc4Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-14Merge branch '2022-03-14-regression-fixes'Tom Rini
- Regression fixes for RK3399 eMMC, j721e Sierra SerDes driver, vexpress64 autoboot and tbs2910 image size
2022-03-14board: tbs2910: Enable Link Time Optimizations in defconfigSoeren Moch
This saves about 12 kBytes image size and helps to stay within the size limit. Suggested-by: Tom Rini <trini@konsulko.com> Signed-off-by: Soeren Moch <smoch@web.de>
2022-03-14vexpress64: fvp: Fix automatic bootAndre Przywara
Commit 90f262a6951f ("vexpress64: Clean up BASE_FVP boot configuration") cleaned up the usage of default address variables, but missed to update the address for the kernel in the FVP's bootcmd definition. Change ${kernel_addr} to read ${kernel_addr_r} to bring back the automated boot for the fastmodel. Also use "setenv" instead of the potentially ambiguous "set" on the way. Fixes: 90f262a6951f ("vexpress64: Clean up BASE_FVP boot configuration") Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-03-14board: ti: j721e: evm.c: Fix the probing of in Sierra SerDes0Aswath Govindraju
Initialization and power on operations of links have been moved under the link device in the Sierra SerDes driver. Also, the UCLASS of sierra_phy_provider has been changed to UCLASS_MISC. Therefore, fix the probing of SerDes0 instance accordingly. Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Georgi Vlaev <g-vlaev@ti.com>
2022-03-14phy: cadence: Sierra: Move the link operations from serdes phy to link deviceAswath Govindraju
In commit 6f46c7441a9f ("phy: cadence: Sierra: Add a UCLASS_PHY device for links"), a separate udevice of type UCLASS_PHY was created for each link. Therefore, move the corresponding link operations under the link device. Also, change the uclass of sierra phy to UCLASS_MISC as it is no longer the phy device. Fixes: 6f46c7441a9f ("phy: cadence: Sierra: Add a UCLASS_PHY device for links") Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Georgi Vlaev <g-vlaev@ti.com>
2022-03-14rockchip: sdhci: Fix RK3399 eMMC PHY power cyclingAlper Nebi Yasak
The Rockchip RK3399 eMMC PHY has to be power-cycled while changing its clock speed to some higher speeds. This is dependent on the desired SDHCI clock speed, and it looks like the PHY should be powered off while setting the SDHCI clock in these cases. Commit ac804143cfd1 ("mmc: rockchip_sdhci: add phy and clock config for rk3399") attempts to do this in the set_ios_post() hook by setting the SDHCI clock once more while the PHY is turned off/on as necessary, as the SDHCI framework does not provide a way to override how it sets its clock. However, the commit breaks reinitializing the eMMC on a few boards including chromebook_kevin and reportedly ROCKPro64. This patch reworks the power cycling to utilize the SDHCI framework slightly better (using the set_control_reg() hook to power off the PHY and set_ios_post() hook to power it back on) which happens to fix the issue, at least on a chromebook_kevin. Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-03-14Merge https://source.denx.de/u-boot/custodians/u-boot-marvellTom Rini
- kwboot: Misc minor improvement and fixes, e.g. mix of arguments (Pali) - PCI: a37xx: Remap IO space to bus address 0x0 (Pali)
2022-03-14Merge https://source.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- Trivial fixes for x86
2022-03-14arm64: zynqmp: Fix i2c addresses for zynqmp-p-a2197Michal Simek
After double checking some i2c addresses are not correct. It is visible from i2c dump ZynqMP> i2c bus Bus 3: i2c@ff020000 74: i2c-mux@74, offset len 1, flags 0 Bus 5: i2c@ff020000->i2c-mux@74->i2c@0 Bus 6: i2c@ff020000->i2c-mux@74->i2c@2 Bus 7: i2c@ff020000->i2c-mux@74->i2c@1 Bus 8: i2c@ff020000->i2c-mux@74->i2c@3 Bus 4: i2c@ff030000 (active 4) 74: i2c-mux@74, offset len 1, flags 0 Bus 9: i2c@ff030000->i2c-mux@74->i2c@0 Bus 10: i2c@ff030000->i2c-mux@74->i2c@3 Bus 11: i2c@ff030000->i2c-mux@74->i2c@4 Bus 12: i2c@ff030000->i2c-mux@74->i2c@5 (active 12) 51: generic_51, offset len 1, flags 0 60: generic_60, offset len 1, flags 0 74: generic_74, offset len 1, flags 0 Bus 13: i2c@ff030000->i2c-mux@74->i2c@6 (active 13) 51: generic_51, offset len 1, flags 0 5d: generic_5d, offset len 1, flags 0 74: generic_74, offset len 1, flags 0 ZynqMP> i2c dev 4 Setting bus to 4 ZynqMP> i2c mw 74 0 18 ZynqMP> i2c probe Valid chip addresses: 18 36 37 50 51 60 74 ZynqMP> i2c mw 74 0 20 ZynqMP> i2c probe Valid chip addresses: 51 60 74 where it is clear that si570 (u5) is at 0x60 address and 8t49n240 (u39) is also at address 0x60 based on log above. i2c address 0x74 is i2c mux and 0x51 is eeprom. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Link: https://lore.kernel.org/r/0a198e9d993411e41473d130d5a5c20b6dc83458.1646639616.git.michal.simek@xilinx.com
2022-03-14pinctrl: zynqmp: Add pinctrl driverAshok Reddy Soma
Add pinctrl driver for Xilinx ZynqMP SOC. This driver is compatible with linux device tree parameters for configuring pinmux and pinconf. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Link: https://lore.kernel.org/r/2d7eefa83c8c0129f7243a25de56a289e948f6c6.1645626183.git.michal.simek@xilinx.com
2022-03-14pinctrl: Increase length of pinmux status bufferAshok Reddy Soma
Xilinx ZynqMP SOC can set 6 parameters for its pins. pinmux status command will print the status of these parameters for each pin. But current print buffer length is only 40 characters long, increase it to 80 to print all the parameters. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Link: https://lore.kernel.org/r/3a6be84c8354f38754a9838670cc0319e84f29e8.1645626183.git.michal.simek@xilinx.com
2022-03-14cmd: test: pinmux: Do not check all empty spacesMichal Simek
There is really no value to check empty spaces. That's why use ut_assert_nextlinen() instead of ut_assert_nextline(). This change ensures that PINMUX_SIZE can be increased without changing tests. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Link: https://lore.kernel.org/r/03aecf4c67ec8d72bf2a90baf1516fc5bd300fe0.1646668094.git.michal.simek@xilinx.com
2022-03-14Merge branch '2022-03-10-platform-updates' into nextTom Rini
- Assorted TI omap3, j7 platform updates - Phytium Pomelo board
2022-03-14arm: a37xx: Remap IO space to bus address 0x0Pali Rohár
Remap PCI I/O space to the bus address 0x0 in the Armada 37xx device-tree in order to support legacy I/O port based cards which have hardcoded I/O ports in low address space. Some legacy PCI I/O based cards do not support 32-bit I/O addressing. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2022-03-14tools: kwboot: Allow to mix positional arguments with option -bPali Rohár
Commit 9e6d71d2b55f ("tools: kwboot: Allow to use -b without image path as the last getopt() option") broke usage of kwboot with following arguments: kwboot -t -B 115200 /dev/ttyUSB0 -b u-boot-spl.kwb Fix parsing of option -b with optional argument again. Fixes: 9e6d71d2b55f ("tools: kwboot: Allow to use -b without image path as the last getopt() option") Signed-off-by: Pali Rohár <pali@kernel.org> Reported-by: Tony Dinh <mibodhi@gmail.com> Tested-by: Tony Dinh <mibodhi at gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
2022-03-14tools: kwboot: Check if baudrate value is supported before sending imagePali Rohár
Call kwboot_open_tty() which baudrate value which was specified at the command line by option -B. This function returns error if baudrate is not supported by selected tty device. Initial baudrate for image transfer is always 115200, so call kwboot_tty_change_baudrate() with value 115200 immediately after kwboot_open_tty() if baudrate specified by option -B is different than 115200. This makes kwboot fail immediately, informing that baudrate is unsupported, instead of failing only after the first part of image is already sent. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2022-03-14tools: kwboot: Allow to specify custom baudrate only in supported operationsPali Rohár
Custom baudrate different than 115200 may be specified only when kwboot is not going to send boot/debug message pattern or when it is going to send boot message pattern with image file (in which case baudrate change happens after sending kwbimage header). BootROM detects boot/debug message pattern only at baudrate 115200. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2022-03-14x86: Correct the coreboot header file in MAINTAINERSSimon Glass
This board has its own config header file. Correct it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-03-14x86: Add an enum name for the GNVS firmware typeSimon Glass
This enum is currently anonymous. Add a name so it can be used in the code. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-03-13Merge tag 'efi-2022-04-rc3-2' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-efi Pull request for efi-2022-04-rc3-2 Documentation: * Fix description for SiFive Unmatched * Add libgnutls28-dev to build dependencies UEFI * Avoid possibly invalid GUID pointers for protocol interfaces Other * Serial console support for cls command
2022-03-12Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-spiTom Rini
- sunXi SPI fixups (Andre) - bcm iproc qspi (Rayagonda)
2022-03-12efi_loader: copy GUID in InstallProtocolInterface()Heinrich Schuchardt
InstallProtocolInterface() is called with a pointer to the protocol GUID. There is not guarantee that the memory used by the caller for the protocol GUID stays allocated. To play it safe the GUID should be copied to U-Boot's internal structures. Reported-by: Joerie de Gram <j.de.gram@gmail.com> Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
2022-03-12doc: add libgnutls28-dev to build dependenciesHeinrich Schuchardt
mkeficapsule requires package libgnutls28-dev for building Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
2022-03-12doc: path to u-boot-spl.bin on SiFive Unmatched boardHeinrich Schuchardt
u-boot-spl.bin is built in spl/. Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-03-12cmd: add serial console support for the cls commandHeinrich Schuchardt
Currently the cls command does not support the serial console The screen can be cleared in the video uclass, the colored frame buffer console, and the serial console by sending the same escape sequence. This reduces the cls command to a single printf() statement on most boards. Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-03-12mtd: spi-nor-ids: Enable quad read for Gigadevice gd25lq128Niklas Cassel
The Gigadevice gd25lq128 serial flash exists in different versions, all which identify themselves using the same JEDEC id. gd25lq128c: https://www.gigadevice.com/datasheet/gd25lq128 gd25lq128d: https://www.gigadevice.com/datasheet/gd25lq128d However, all versions support quad read, so enable it. Tested and verified on the Sipeed MAix BiT board. Fixes: 30b9a28a3f2d ("mtd: spi-nor-ids: Add Gigadevice gd25lq128 ID") Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2022-03-10arm: add initial support for the Phytium Pomelo Boardweichangzheng
This adds platform code and the device tree for the Phytium Pomelo Board. The initial support comprises the UART and the PCIE. Signed-off-by: weichangzheng <nicholas_zheng@outlook.com>
2022-03-10ARM: mach-omap2: omap3: Make clock functions staticAdam Ford
get_osc_clk_speed and get_sys_clkin_sel are only used in one file. Make them static. Tested on OMAP3530, DM3730, AM3517. Signed-off-by: Adam Ford <aford173@gmail.com>
2022-03-10ARM: am3517_evm: Remove hard-coded pin muxingAdam Ford
With updated device trees now supporting pinmuxing for USB, ethernet, MMC, and other peripherals necessary to start MLO and U-Boot, the hard-coded pinmux options can be removed since they are now handed by DM and only muxed when the respective peripheral needs it. Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Derald D. Woods <woods.technical@gmail.com>
2022-03-10ARM: dts: am3517-evm: Sync DTS with Linux 5.17-rc5Adam Ford
Sync the am3517-evm device tree files with those from Linux 5.17-rc5 with some additional fixes for pinmuxing Ethernet and moving the pinmux references to the respective peripherals. Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Derald D. Woods <woods.technical@gmail.com>
2022-03-10ARM: dts: logicpd-torpedo: Resyc DTS files with Linux 5.17-rc5Adam Ford
Resyc DTS files with Linux 5.17-rc5. Signed-off-by: Adam Ford <aford173@gmail.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-11 04:29:08 +0000