aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2021-07-15configs: am335x_guardian: Enable bootcount nvmem supportGireesh Hiremath
include bootcount nvmem support Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210611161350.2141-18-Gireesh.Hiremath@in.bosch.com
2021-07-15am335x, guardian: software update available status is stored in AM3352 RTC ↵Gireesh Hiremath
scracth register RTC second scratch register[32-bit]: -zero byte hold boot count value -first byte hold update available state -second byte hold version -third byte hold magic number Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210611161350.2141-17-Gireesh.Hiremath@in.bosch.com Gbp-Pq: Topic apertis/guardian Gbp-Pq: Name am335x-guardian-software-update-available-status-is-store.patch
2021-07-15am335x, guardian: Enable panel driver Himax HX8238DGireesh Hiremath
- Enable lcd controller - Display splash screen Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210611161350.2141-16-Gireesh.Hiremath@in.bosch.com
2021-07-15drivers: video: hx8238 fix build bugGireesh Hiremath
update panel driver hx8238 fix build bug Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210611161350.2141-15-Gireesh.Hiremath@in.bosch.com
2021-07-15configs: am335x_guardian: Enable display configGireesh Hiremath
-Enable configuration for display driver -Disable support for SPL GPIO, CMD LED & SPL GPIO Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210611161350.2141-14-Gireesh.Hiremath@in.bosch.com
2021-07-15am335x, guardian: Enable backlightGireesh Hiremath
Enable backlight, set brightness value and dimming frequency Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210611161350.2141-13-Gireesh.Hiremath@in.bosch.com
2021-07-15am335x, guardian: update swi logicGireesh Hiremath
read boot mode gpio and set the swi status Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210611161350.2141-12-Gireesh.Hiremath@in.bosch.com
2021-07-15configs: am335x_guardian: disable spl commandGireesh Hiremath
- disable support for spl command Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210611161350.2141-11-Gireesh.Hiremath@in.bosch.com
2021-07-15configs: am335x_guardian: set boot delayGireesh Hiremath
- set boot delay to zero, to increase boot speed Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210611161350.2141-10-Gireesh.Hiremath@in.bosch.com
2021-07-15am335x, guardian: code cleanup and boot optimizationGireesh Hiremath
- remove redundant headers and boot modes from board file Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210611161350.2141-9-Gireesh.Hiremath@in.bosch.com
2021-07-15am335x, guardian: set environment variable autoload to noGireesh Hiremath
autoload: if set to "no" then rarpb, bootp or dhcp commands will just perform a configuration lookup from the BOOTP / DHCP server, but not try to load any image using TFTP Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210611161350.2141-8-Gireesh.Hiremath@in.bosch.com
2021-07-15am335x, guardian: Update pinmux configurationMoses Christopher
pinmux update for guardian board - control ASP Board Power: GPIO, on/off ASP Board Power - control Coincell Voltage Measurement: GPIO, enable/disable ADC measurements - powerOff Device GPIO-PowerOff, cut the PMIC supply Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210611161350.2141-7-Gireesh.Hiremath@in.bosch.com
2021-07-15configs: am335x_guardian: add memtest configsGireesh Hiremath
- Add mtest, meminfo commands Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210611161350.2141-6-Gireesh.Hiremath@in.bosch.com
2021-07-15am335x, guardian: set tftp_load_addr in environmentMoses Christopher
Set tftp_load_addr to 0x82000000 in MEM_LAYOUT_ENV_SETTINGS Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210611161350.2141-5-Gireesh.Hiremath@in.bosch.com
2021-07-15configs: am335x_guardian: add ubi fastmap supportGireesh Hiremath
- Trigger fastmap automatically Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210611161350.2141-4-Gireesh.Hiremath@in.bosch.com
2021-07-15am335x, guardian: mem: Add board dependent mem valuesMoses Christopher
- Add mem-guardian.h derived from am33xx/mem.h * Add GPMC config values optimized for Bosch Guardian Board * NAND Chip used by Bosch Guardian Board is Micron MT29F4G08ABBFA Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210611161350.2141-3-Gireesh.Hiremath@in.bosch.com
2021-07-15configs: am335x_guardian: Enable clock driverGireesh Hiremath
Enable TI clock driver support for guardian board Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210611161350.2141-2-Gireesh.Hiremath@in.bosch.com
2021-07-14Merge branch '2021-07-14-build-and-host-updates'Tom Rini
- Resync Kbuild with the v4.20 Linux Kernel release - Update checkpatch.pl - Assorted other tooling updates
2021-07-14scripts/get_default_envs.sh: Update for thin archive supportTom Rini
This script was broken by the change to default archives for linking. This is due to objcopy specifically disallowing copying of thin archives. To fix this and re-support external users of this script, switch to using the same logic the u-boot-initial-env make target uses to dump the section from the object file. Reported-by: Jan Kiszka <jan.kiszka@web.de> Fixes: 958f2e57eff7 ("build: use thin archives instead of incremental linking") Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-14Makefile: Conditionally add defaultenv_h to envtools targetJoel Stanley
When building the envtools target with CONFIG_USE_DEFAULT_ENV_FILE=y, the tools require generated/defaultenv_autogenerated.h. In file included from tools/env/fw_env.c:126: include/env_default.h:115:10: fatal error: generated/defaultenv_autogenerated.h: No such file or directory 115 | #include "generated/defaultenv_autogenerated.h" | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-07-14kconfig / kbuild: Re-sync with Linux 4.20Tom Rini
Align Kconfig and Kbuild logic to Linux 4.20 release with minimal impact on files outside of this scope. Our previous Kconfig sync was done by commit 587e4a429698 ("kconfig / kbuild: Re-sync with Linux 4.19"). As part of this re-sync, a few related changes from previous Linux releases were found to have been missed and merged in, and are not in the following list. The imported Linux commits are: [From prior to v4.19] b1e0d8b70fa3 kbuild: Fix gcc -x syntax a4353898980c kconfig: add CC_IS_GCC and GCC_VERSION 469cb7376c06 kconfig: add CC_IS_CLANG and CLANG_VERSION [From v4.19 to v4.20] 487c7c7702ab kbuild: prefix Makefile.dtbinst path with $(srctree) unconditionally 0d91bf584fe5 kbuild: remove old check for CFLAGS use 25815cf5ffec kbuild: hide most of targets when running config or mixed targets 00d78ab2ba75 kbuild: remove dead code in cmd_files calculation in top Makefile 23066c3f4e21 Compiler Attributes: enable -Wstringop-truncation on W=1 (gcc >= 8) 37c8a5fafa3b kbuild: consolidate Devicetree dtb build rules 80463f1b7bf9 kbuild: add --include-dir flag only for out-of-tree build 77ec0c20c7e0 kbuild: remove VERSION and PATCHLEVEL from $(objtree)/Makefile 74bc0c09b2da kbuild: remove user ID check in scripts/mkmakefile 4fd61277f662 kbuild: do not pass $(objtree) to scripts/mkmakefile 80d0dda3a4e5 kbuild: simplify command line creation in scripts/mkmakefile fb073a4b473e kbuild: add -Wno-pointer-sign flag unconditionally 9df3e7a7d7d6 kbuild: add -Wno-unused-but-set-variable flag unconditionally 69ea912fda74 kbuild: remove unneeded link_multi_deps 7d0ea2524202 kbuild: use 'else ifeq' for checksrc to improve readability 04c459d20448 kconfig: remove oldnoconfig target 0085b4191f3e kconfig: remove silentoldconfig target 3f80babd9ca4 kbuild: remove unused cc-fullversion variable 2cd3faf87d2d merge_config.sh: Allow to define config prefix 076f421da5d4 kbuild: replace cc-name test with CONFIG_CC_IS_CLANG 6bbe4385d035 kconfig: merge_config: avoid false positive matches from comment lines [From post v4.20] 885480b08469 Makefile: Move -Wno-unused-but-set-variable out of GCC only block There are a number of changes related to additional warnings as well as being able to drop cc-name entirely that have been omitted for now as additional work is required first. Cc: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-14get_maintainer.pl: update from Linux kernel v5.13-rc6Trevor Woerner
Update U-Boot's version of scripts/get_maintainer.pl to sync it up with the latest changes to the Linux kernel's version of the same script. The last sync was with Linux kernel version v4.16. The commits to the kernel's get_maintainer.pl since then (starting with the most recent) are: 6343f6b71f83 get_maintainer: exclude MAINTAINERS file(s) from --git-fallback cdfe2d220476 get_maintainer: add test for file in VCS e33c9fe8b80c get_maintainer: fix unexpected behavior for path/to//file (double slashes) 0c78c0137621 get_maintainer: add email addresses from .yaml files 0ef82fcefb99 scripts/get_maintainer.pl: deprioritize old Fixes: addresses ef0c08192ac0 get_maintainer: remove uses of P: for maintainer name 2f5bd343694e scripts/get_maintainer.pl: add signatures from Fixes: <badcommit> lines in commit message 49662503e8e4 get_maintainer: add ability to skip moderated mailing lists 0fbd75fd7fee get_maintainer: allow option --mpath <directory> to read all files in <directory> 5f0baf95b1ed get_maintainer.pl: add -mpath=<path or file> for MAINTAINERS file location 31bb82c9caa9 get_maintainer: allow usage outside of kernel tree 0455c74788fd get_maintainer: improve patch recognition 882ea1d64eb3 scripts: use SPDX tag in get_maintainer and checkpatch Signed-off-by: Trevor Woerner <twoerner@gmail.com>
2021-07-14lib: move rtc-lib.c to libHeinrich Schuchardt
Function rtc_to_tm() is needed for FAT file system support even if we don't have a real time clock. So move it from drivers/ to lib/. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2021-07-14tools: image-host: fix wrong return valueMing Liu
The return value '-ENOSPC' of fit_set_timestamp function does not match the caller fit_image_write_sig's expection which is '-FDT_ERR_NOSPACE'. Fix it by not calling fit_set_timestamp, but call fdt_setprop instead. This fixes a following mkimage error: | Can't write signature for 'signature@1' signature node in | 'conf@imx6ull-colibri-wifi-eval-v3.dtb' conf node: <unknown error> | mkimage Can't add hashes to FIT blob: -1 Signed-off-by: Ming Liu <liu.ming50@gmail.com> Tested-by: Igor Opaniuk <igor.opaniuk@foundries.io>
2021-07-14tools/fitimage: add missing linebreak for some messagesSven Roederer
Add a linebreak to two messages and fix punctuation. Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
2021-07-14fixdep: remove leftover handling of IS_BUILTIN/IS_MODULERasmus Villemoes
I removed CONFIG_IS_BUILTIN and CONFIG_IS_MODULE in commit 7d78a4547d ("linux/kconfig.h: remove unused helper macros"), but fixdep.c still looks for those. It's harmless, but also pointless and possibly confusing to a future reader. Fixes: 7d78a4547d ("linux/kconfig.h: remove unused helper macros") Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2021-07-14mkimage: allow -l to work on block devices on LinuxYann Dirson
When "mkimage -l" was run on a block device it would fail with erroneous message, because fstat reports a size of zero for those: mkimage: Bad size: "/dev/sdb4" is not valid image This patch identifies the "is a block device" case and reports it as such, and if it knows how to determine the size of a block device on the current OS, proceeds. As shown in http://www.mit.edu/afs.new/sipb/user/tytso/e2fsprogs/lib/blkid/getsize.c this is no portable task, and I only handled the case of a modern Linux kernel, which is what I can test. Signed-off-by: Yann Dirson <yann@blade-group.com>
2021-07-14Merge branch '2021-07-14-platform-updates'Tom Rini
- Assorted platform updates
2021-07-14usb: musb-new: Add glue driver for ST-Ericsson Ux500Stephan Gerhold
The ST-Ericsson DB8500 SoC contains a MUSB OTG controller which supports both host and gadget mode. For some reason there is nothing special about it - add a simple glue driver for Ux500 that literally just sets up MUSB together with a generic PHY. There are no SoC-specific registers etc needed to make USB work. The new Ux500 glue driver is only tested to work with DM_USB and DM_USB_GADGET. Both host and gadget mode work fine on the u8500 "stemmy" board that is already present in U-Boot. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
2021-07-14phy: Add driver for ST-Ericsson AB8500 USB PHYStephan Gerhold
The AB8500 PMIC contains an USB PHY that needs to be set up in device or host mode to make USB work properly. Add a simple driver for the generic PHY uclass that allows enabling it. The if (CONFIG_IS_ENABLED(USB_MUSB_HOST)) might be a bit strange. The USB PHY must be configured in either host or device mode and somehow the USB PHY driver must be made aware of the mode. Actually, the MUSB driver used together with this PHY does not support dynamic selection of host/device mode in U-Boot at the moment. Therefore, one very simple approach that works fine is to select the mode to configure at compile time. When the MUSB driver is configured in host mode the PHY is configured in host mode, and similarly when the MUSB driver is configured in device/gadget mode. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-07-14power: pmic: Add driver for ST-Ericsson AB8500 via PRCMUStephan Gerhold
All devices based on ST-Ericsson Ux500 use a PMIC similar to AB8500 (Analog Baseband). There is AB8500, AB8505, AB9540 and AB8540 although in practice only AB8500 and AB8505 are relevant since the platforms with AB9540 and AB8540 were cancelled and never used in production. In general, the AB8500 PMIC uses I2C as control interface, where the different register banks are represented as separate I2C devices. However, in practice AB8500 is always connected to a special I2C bus on the DB8500 SoC that is controlled by the power/reset/clock management unit (PRCMU) firmware. Add a simple driver that allows reading/writing registers of the AB8500 PMIC. The driver directly accesses registers from the PRCMU parent device (represented by syscon in U-Boot). Abstracting it further (e.g. with the i2c uclass) would not provide any advantage because the PRCMU I2C bus is always just connected to AB8500 and vice-versa. The ab8500.h header is mostly taken as-is from Linux (with some minor adjustments) to allow using similar code in both Linux and U-Boot. Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-07-14board: stemmy: Copy atags for booting downstream/vendor kernelStephan Gerhold
The U-Boot "stemmy" board is mainly intended to simplify booting mainline Linux on various smartphones from Samsung based on ST-Ericsson Ux500. While the mainline kernel is working great, there are still some features missing there. In particular, it is currently not possible to charge the battery when using the mainline kernel. This means that it is still necessary to boot the downstream/vendor kernel from Samsung sometimes to charge the device. That kernel is ancient, still uses board files + ATAGS instead of device trees and relies on a strange very long kernel command line hardcoded in the Samsung bootloader. Actually, since mainline is booted with device trees there is a very simple way to make the old downstream kernel work as well: We can simply take most of the ATAGS passed to U-Boot from the Samsung bootloader and copy them as-is when booting a kernel without device tree. That way the long command line and other needed ATAGS are copied as-is without having to bother with them. The only exception is the ATAG_INITRD - since the initrd is loaded by U-Boot, the atag for that should be generated in U-Boot so it points to the correct address. All other ATAGS are copied as-is and not generated in U-Boot. Also use the chance and provide a serial# for U-Boot by parsing the ATAG_SERIAL that is also passed by the Samsung bootloader. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2021-07-14board: stemmy: Parse atags to get available memoryStephan Gerhold
At the moment the "stemmy" board attempts to detect the RAM size with a simple memory test (get_ram_size()). Unfortunately, this does not work correctly for devices with 768 MiB RAM (e.g. Samsung Galaxy Ace 2 (GT-I8160), "codina"). Reading/writing memory after the 768 MiB RAM succeeds but actually overwrites some earlier parts of the memory. For U-Boot this does not result in any major problems, but on Linux this will eventually lead to strange crashes because of the memory corruption. Since the "stemmy" U-Boot port is designed to be chainloaded from the original Samsung bootloader, the most reliable way to get the available amount of RAM is to look at the ATAGS passed by the Samsung bootloader. Fortunately, the header used to generate ATAGS in U-Boot (asm/setup.h) can also be easily used to parse them. Also clarify and simplify stemmy.h a bit to make it more clear where some of the magic values in there are actually coming from. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2021-07-14ARM: dts: uniphier: Add support for Akebi96Kunihiko Hayashi
Add the device tree for Akebi96. Akebi96 is a 96boards certified development board based on UniPhier LD20. ( https://www.96boards.org/product/akebi96/ ) Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
2021-07-14configs: uniphier: Enable CONFIG_SYS_PCI_64BITKunihiko Hayashi
Enable CONFIG_SYS_PCI_64BIT to allow 64bit access to PCI space. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
2021-07-14pci: uniphier: Add UniPhier PCIe controller driverKunihiko Hayashi
Add PCIe driver for UniPhier SoCs. This PCIe controller is based on Synopsys DesignWare Core IP. This version doesn't apply common DW functions because supported controller doesn't have unroll version of iATU. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
2021-07-14phy: socionext: Add UniPhier PCIe PHY driverKunihiko Hayashi
Add PCIe PHY driver support for Pro5, LD20 and PXs3 SoCs. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
2021-07-14reset: uniphier: Add PCIe reset entryKunihiko Hayashi
Add reset control for PCIe controller on each SoC. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
2021-07-14clk: uniphier: Add PCIe clock entryKunihiko Hayashi
Add clock control for PCIe controller on each SoC. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
2021-07-14MAINTAINERS, git-mailrc: socfpga: Change co-maintainer to Tien Fong CheeLey Foon Tan
I'm no longer work in Intel, change Intel SoCFPGA co-maintainer to Tien Fong Chee. Signed-off-by: Ley Foon Tan <lftan.linux@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
2021-07-14arm: mach-snapdragon: pinctrl: Place pin_name in .data sectionStephan Gerhold
According to arch/arm/lib/crt0_64.S, the BSS section is "UNAVAILABLE" and uninitialized before relocation. Also, it overlaps with the appended DTB before relocation, so writing data into a variable in the BSS section might corrupt the appended DTB. Unfortunately, pinctrl-apq8016.c and pinctrl-apq8096.c do place the "pin_name" variable in the BSS section (since it's uninitialized). It's also used before relocation, when setting up the pinctrl for the serial driver. On DB410c this causes "GPIO_5" to be written into some part of an appended DTB, e.g.: 80111820: edfe0dd0 9f100000 38000000 c00e0000 ...........8.... 80111830: 28000000 11000000 10000000 00000000 ...(............ 80111840: 4f495047 8800355f 00000000 00000000 GPIO_5.......... 80111850: 00000000 00000000 01000000 00000000 ................ 80111860: 03000000 04000000 00000000 02000000 ................ 80111870: 03000000 04000000 0f000000 02000000 ................ 80111880: 03000000 2d000000 1b000000 6c617551 .......-....Qual 80111890: 6d6d6f63 63655420 6c6f6e68 6569676f comm Technologie Depending on the part of the DTB that is corrupted this might not cause any problems, but it can also result in strange reboots without any serial output. Fortunately, in practice this does not cause issues on DB410c yet because board_fdt_blob_setup() in dragonboard410c.c currently overrides the appended DTB with the one passed by the previous bootloader (LK) (which does not get corrupted). DB820c does not have board_fdt_blob_setup() so I would expect it to be affected by this problem. Perhaps everyone was just fortunate to not compile an U-Boot configuration where the pin_name corrupts an important part of the DTB. Make sure "pin_name" is explicitly placed in the .data section instead of .bss to fix this. Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-07-14board-info: Call sysinfo_detect() before sysinfo_get_str()Marek Vasut
The sysinfo_get_str() implementation checks whether the sysinfo was even detected. In U-Boot proper, sysinfo_detect() is not called anywhere but on one specific board. Call sysinfo_detect() before sysinfo_get_str() to make sure the sysinfo is detected and sysinfo_get_str() returns valid value instead of -EPERM. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-07-14board-info: Use sysinfo_get()Marek Vasut
Replace uclass_first_device_err(UCLASS_SYSINFO, &dev) with sysinfo_get(&dev). The board_info code may use sysinfo to print board information, so use the sysinfo functions consistently. The sysinfo_get() is internally implemented as return uclass_first_device_err(UCLASS_SYSINFO, &dev) anyway, so there is no functional change. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-07-14misc: i2c_eeprom: Add atmel,24c01 to the listMarek Vasut
Linux kernel binding is using atmel,24c01 compatible string. On the other hand there is atmel,24c01a which is not listed in the kernel. Add compatible string without "a" suffix to be compatible with Linux kernel binding. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Heiko Schocher <hs@denx.de> Cc: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-14timer: nomadik-mtu: Use dev_read_addr_ptr()Stephan Gerhold
Simplify the code a bit by using dev_read_addr_ptr() instead of dev_read_addr(). This avoids having to cast explicitly to the struct nomadik_mtu_regs. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2021-07-14gpio: Add driver for Nomadik GPIOStephan Gerhold
Nomadik GPIO is a fairly simple GPIO module used in the ST-Ericsson Ux500 SoCs (and some older Nomadik SoCs). It uses registers where each GPIO is represented as a single bit, plus "set" and "clear" registers that allow updating the state without having to read the existing state. The driver implements support for it for use together with DM_GPIO and the existing ste-dbx5x0.dtsi device tree. Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2021-07-14gpio: Drop long unused DB8500 GPIO driverStephan Gerhold
The original U-Boot port for the ST-Ericsson U8500 SoC was dropped in commit 68282f55b846 ("arm: Remove unused ST-Ericsson u8500 arch"). Most of the drivers related to the old port were removed, but the db8500_gpio.c driver was forgotten for some reason. There is no way to select it and it does not compile anymore because of missing headers, so let's just remove it. The new port for U8500 introduced in commit 689088f9dae8 ("arm: Add support for ST-Ericsson U8500 SoC") fully embraces the new Driver Model and device trees where possible, so this is preparation to add a new, simplified GPIO driver based on DM_GPIO. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2021-07-14board: armltd: Remove bootargs from Total Compute configurationAnders Dellien
This information will be maintained in the device tree instead. Signed-off-by: Anders Dellien <anders.dellien@arm.com>
2021-07-13Merge tag 'efi-2021-10-rc1' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-efi Pull request for efi-2021-10-rc1 Documentation * fix typo in signature.txt UEFI * provide file attributes in EFI_FILE_PROTOCOL.Read() * various capsule update fixes
2021-07-12efi_loader: Fix to set bootdev_root correctly if bootdev foundMasami Hiramatsu
Fix find_boot_device() to set bootdev_root if it finds the bootdev from BootNext. Currently it sets the bootdev_root only when it finds bootdev from BootOrder. Fixes: c74cd8bd08d1 ("efi_loader: capsule: add capsule_on_disk support") Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org> Accked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-15 16:48:30 +0000