aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-06-07rockchip: puma: reorganize devicetrees to actually work and match upstreamHeiko Stuebner
So far the puma dts files only just included the main puma dtsi without handling the actual baseboard and rk3399-puma.dtsi was very much detached from the variant in the mainline Linux kernel. Recent changes resulted in a strange situation with nonworking puma boards. Commit ab800e5a6f28 ("arm: dts: rockchip: puma: move U-Boot specific bits to u-boot.dtsi") moved the sdram include from rk3399-puma-ddrX.dts to new files rk3399-puma-ddrx-u-boot.dtsi which were never included anywhere though. Commit 167efc2c7a46 ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux") replaced the rk3399-puma.dtsi nearly completely, but in the kernel it definitly depends on a baseboard dts to actually enable peripherals like sd-slot, uarts, etc. So to untagle this and bring the whole thing more in line with mainline Linux, bring the rk3399-puma-haikou.dts over as well, drop the separate DDR-option devicetrees and instead replace them with a puma Kconfig option to select and include the needed DDR variant. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: puma: fix indentation of misc_init_rHeiko Stuebner
The commit moving puma to the generic cpuid/macaddr helpers used 7 spaces as indentation, so correct that by moving to the required tabs. Fixes: fa177ff0208b ("board: puma: Use rockchip_* helpers to setup cpuid and macaddr") Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: puma: fix indentation for -u-boot.dtsiHeiko Stuebner
Tabs not spaces, so transform it to the common styling. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07arm64: dts: rk3399-puma: fix gpio levels for vcc5v0-host regulatorHeiko Stuebner
The regulator enable-gpio uses opposite values for the declaration vs. the enable_active_low property, breaking the regulator enablement. Make the usbhost-supply work again by bringing them in sync again. This mimics the upstream Linux change found on: http://lore.kernel.org/r/20200604091239.424318-1-heiko@sntech.de Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2020-06-07arm64: dts: rk3399-puma: fix gpio levels for gmac reset pinHeiko Stuebner
The gmac reset has opposite values for the gpio declaration and the separate reset-active, bring this in line to make u-boot also find the ethernet-phy. This mimics the upstream Linux commit found on https://lore.kernel.org/r/20200603132836.362519-1-heiko@sntech.de Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rockpro64: add SPI bootMarcin Juszkiewicz
U-Boot TPL 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42) Channel 0: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB 256B stride 256B stride lpddr4_set_rate: change freq to 400000000 mhz 0, 1 lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42 +0200) Trying to boot from SPI U-Boot 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42 +0200) SoC: Rockchip rk3399 Reset cause: RST Model: Pine64 RockPro64 v2.1 DRAM: 3.9 GiB PMIC: RK808 MMC: mmc@fe310000: 2, mmc@fe320000: 1, sdhci@fe330000: 0 Loading Environment from SPI Flash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment In: serial Out: vidconsole Err: vidconsole Model: Pine64 RockPro64 v2.1 Net: eth0: ethernet@fe300000 Hit any key to stop autoboot: 0 => Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rockpro64: Store default env into SPIMarcin Juszkiewicz
Board has flash chip on board so let store U-Boot environment there. Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07doc: rockchip: Document SPI flash program stepsJagan Teki
Document SPI flash program steps for rockchip platforms. Suggested-by: Hugh Cole-Baker <sigmaris@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07roc-rk3399-pc: Add SPI bootJagan Teki
U-Boot TPL 2020.07-rc3-00090-gd4e919f927-dirty (Jun 01 2020 - 23:45:53) Channel 0: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB 256B stride 256B stride lpddr4_set_rate: change freq to 400000000 mhz 0, 1 lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2020.07-rc3-00087-ga21e9fd385 (Jun 02 2020 - 00:09:45 +0530) Trying to boot from MMC1 NOTICE: BL31: v2.2(release): NOTICE: BL31: Built : 15:05:37, May 12 2020 U-Boot 2020.07-rc3-00087-ga21e9fd385 (Jun 02 2020 - 00:09:45 +0530) SoC: Rockchip rk3399 Reset cause: POR Model: Firefly ROC-RK3399-PC Board DRAM: 3.9 GiB PMIC: RK808 MMC: mmc@fe320000: 1, sdhci@fe330000: 0 Loading Environment from SPI Flash... SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Model: Firefly ROC-RK3399-PC Board Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07roc-rk3399-pc: Mark default env from SPIJagan Teki
Mark the default U-Boot environment as SPI flash since this is an on board flash device. Updated env offset, size in contrast with default since the U-Boot proper has to start from 384K. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07Makefile: Drop to handle rkspi image typeJagan Teki
On rockchip platforms, SPI boot image creation is not straightforward like MMC boot image creation where former requires to specify tpl, spl in multimage format in mkimage, and later simply do a concatenate mkimaged-tpl with spl. On this note, let drop rkspi image type creation via kbuild and let inform via rockchip.rst Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rk3399-evb: add stdout-path for the boardKever Yang
The 'stdout-path' is missing after dts sync. Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux") Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rk3328: add rock-pi-e-rk3328_defconfig fileb.l.huang
This commit add the default configuration file and relevant description for rock-pi-e board Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
2020-06-07rockchip: rk3328: add rock-pi-e dts fileb.l.huang
The ROCK-PI-E is a credit card size SBC based on Rockchip RK3328 Quad-Core ARM Cortex A53. Net - Dual ethernet port, 1 X Gbe, 1 X 100M USB - USB 3.0 DC - USB-Type C, 5V 2A Storage - TF card, eMMC Just build idbloader.img and u-boot.itb for Rockpi E board and follow the blow steps to replace the relevant partition. dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
2020-06-07rockchip: Enable PCIe and NVMe on ROCKPro64Mark Kettenis
Enable CONFIG_PCI and CONFIG_NVME and related configs for the ROCKPro64 board. Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: Enable PCIe/M.2 and NVMe on Firefly RK3399Mark Kettenis
Enable CONFIG_PCI and CONFIG_NVME and related configs for the Firefly RK3399 board. Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-04configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04Merge branch '2020-06-04-misc-bugfixes'Tom Rini
- Resync checkpatch.pl (largely) with v5.7 and introduce U-Boot specific checks in a localized area, so they aren't lost in the future. - Complete / re-migrate some options from config headers to defconfigs - Add dependencies to the various debug uart drivers
2020-06-04checkpatch.pl: Add check for defining CONFIG_CMD_xxx via config filesTom Rini
All of our cmds have a Kconfig entry. Making enabling a CMD via the config file an error to checkpatch.pl. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04checkpatch.pl: Request if() instead #ifdefSimon Glass
There is a lot of use of #ifdefs in U-Boot. In an effort reduce this, suggest using the compile-time construct. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-06-04checkpatch.pl: Request a test when a new command is addedSimon Glass
This request is made with nearly every new command. Point to some docs on how to do it. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-06-04checkpatch.pl: Warn if the flattree API is usedSimon Glass
We want people to use the livetree API, so request it. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-06-04checkpatch.pl: Add a check for tests needed for uclassesSimon Glass
A common problem when submitting a new uclass is to forget to add sandbox tests. Add a warning for this. Of course tests should always be added for new code, but this one seems to be missed by nearly every new contributor. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-06-04checkpatch.pl: Add a U-Boot optionSimon Glass
Add an option to indicate that U-Boot-specific checks should be enabled. Add a function to house the code that will be added. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-06-04checkpatch.pl: Update to v5.7Simon Glass
Keep the U-Boot changes to $logFunctions Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Resync with v5.7 release which changed the default max line length, update commit to reflect] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04Convert CONFIG_BOARD_LATE_INIT to KconfigTom Rini
This converts the following to Kconfig: CONFIG_BOARD_LATE_INIT Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04Convert CONFIG_CMD_ASKENV et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CMD_ASKENV CONFIG_CMD_BMP CONFIG_CMD_BOOTD CONFIG_CMD_CACHE CONFIG_CMD_CRC32 CONFIG_CMD_DHCP CONFIG_CMD_ENV CONFIG_CMD_EXPORTENV CONFIG_CMD_EXT2 CONFIG_CMD_EXT4 CONFIG_CMD_FLASH CONFIG_CMD_FS_GENERIC CONFIG_CMD_FUSE CONFIG_CMD_GPIO CONFIG_CMD_GPT CONFIG_CMD_GREPENV CONFIG_CMD_I2C CONFIG_CMD_IMLS CONFIG_CMD_IMPORTENV CONFIG_CMD_LOADB CONFIG_CMD_LOADS CONFIG_CMD_MEMINFO CONFIG_CMD_MII CONFIG_CMD_MTDPARTS CONFIG_CMD_NAND CONFIG_CMD_NAND_TRIMFFS CONFIG_CMD_NFS CONFIG_CMD_PCA953X CONFIG_CMD_PCA953X_INFO CONFIG_CMD_PCI CONFIG_CMD_PING CONFIG_CMD_READ CONFIG_CMD_SF CONFIG_CMD_SPI CONFIG_CMD_SPL CONFIG_CMD_SPL_WRITE_SIZE CONFIG_CMD_TIME CONFIG_CMD_TRACE CONFIG_CMD_UBI CONFIG_CMD_UBIFS CONFIG_CMD_UNZIP CONFIG_FS_EXT4 Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04Convert CONFIG_BZIP2 et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_BZIP2 CONFIG_GZIP CONFIG_LZO CONFIG_ZLIB CONFIG_LZMA CONFIG_LZO Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04topic_miami: Disable GPIOTom Rini
Per the boards config header file, there is no useful GPIO on these boards. Remove CONFIG_CMD_GPIO from the defconfigs. Cc: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04ARM: rmobile: blanche: Disable CONFIG_CMD_SF / CONFIG_CMD_SPITom Rini
The config header for this platform disables both CMD_SF and CMD_SPI and the defconfig leaves them enabled. Disable them from the defconfig and enable them in the header. Cc: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04bcmstb: Migrate CONFIG_CMD_EXT[24]Tom Rini
The common config header for bcm7260 and bcm7445 enable CONFIG_CMD_EXT2/EXT4 but the defconfigs do not. This results in the commands being disabled. Enable them via the defconfig. Cc: Thomas Fitzsimmons <fitzsim@fitzsim.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04mx6memcal: Finish migration to defconfig optionsTom Rini
The config header for this platform uses '#undef' in a number of cases. All of the MMC related ones were already handled correctly in the defconfig file. In the case of CONFIG_CMD_FUSE, the command was being built and enabled via defconfig. Disable it in the defconfig, cleanup the header. Reviewed-by: Eric Nelson <eric@nelint.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04pfla02: Rework excluding NAND from SPLTom Rini
Rather than only enable CONFIG_CMD_NAND for non-SPL builds, move the CMD options to defconfig and rework the guards to not try and call the function in SPL builds. Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Stefano Babic <sbabic@denx.de>
2020-06-04serial: Add missing Kconfig dependencies for debug consolesMichal Simek
Debug console is the part of serial driver in the same file. It means to be able to enable debug console you also need to enable driver itself. That's why add all dependecies and list only debug consoles which are enabled based on driver selection to avoid compilation error when user asks for certain debug console but driver is not enable for it. Error: aarch64-linux-gnu-ld.bfd: common/built-in.o: in function `putc': /home/monstr/data/disk/u-boot/common/console.c:513: undefined reference to `printch' aarch64-linux-gnu-ld.bfd: common/built-in.o: in function `puts': /home/monstr/data/disk/u-boot/common/console.c:563: undefined reference to `printch' Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org> [trini: Fix ns16550 dependency, add ZYNQ_SERIAL, change S5P] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04serial: Convert ARM_DCC to KconfigTom Rini
The symbol "CONFIG_ARM_DCC" is used to control building drivers/serial/arm_dcc.c. Provide a simple Kconfig entry for this. Cc: Luca Ceresoli <luca@lucaceresoli.net> Cc: Michal Simek <monstr@monstr.eu> Cc: Tom McLeod <tom.mcleod@opalkelly.com> Cc: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
2020-06-04Merge https://gitlab.denx.de/u-boot/custodians/u-boot-riscvTom Rini
- Fixes 7e249bc13aaf: ("riscv: Move all SMP related SBI calls to SBI_v01") Move sbi_probe_extension() out of CONFIG_SBI_V01. - SiFive FU540 support SPL.
2020-06-04Merge tag 'u-boot-atmel-fixes-2020.07-a' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel First set of u-boot-atmel fixes for 2020.07 cycle This set includes just two small commits that fix a build warning and add a missing serial node.
2020-06-04riscv: sbi: Move sbi_probe_extension() out of CONFIG_SBI_V01Bin Meng
sbi_probe_extension() is an API defined in SBI v0.2, not v0.1. Fixes 7e249bc13aaf: ("riscv: Move all SMP related SBI calls to SBI_v01") Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Rick Chen <rick@andestech.com>
2020-06-04riscv: sbi: Remove sbi_spec_versionBin Meng
U-Boot defaults to use SBI v0.2. Howerver there is a global variable sbi_spec_version that stills refers to v0.1. Since it is not used anywhere, let's remove it. Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Rick Chen <rick@andestech.com>
2020-06-04doc: sifive: fu540: Add description for OpenSBI generic platformPragnesh Patel
OpenSBI generic platform support provides platform specific functionality based on the FDT passed by previous booting stage. Depends on OpenSBI commit: platform: Add generic FDT based platform support (sha1: f1aa9e54e00006ae70aeac638d5b75093520f65d) Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-04configs: fu540: Add config options for U-Boot SPLPragnesh Patel
With sifive_fu540_defconfig: User can use FSBL or u-boot-spl.bin anyone at a time. For FSBL, fsbl->fw_payload.bin (opensbi + U-Boot) For u-boot-spl.bin, u-boot-spl.bin->FIT image (opensbi + U-Boot proper + dtb) U-Boot SPL will be loaded by ZSBL from SD card (replace fsbl.bin with u-boot-spl.bin) and runs in L2 LIM in machine mode and then load FIT image u-boot.itb from SD card into RAM. U-Boot SPL expects u-boot.itb FIT image at the starting of SD card sector number (0x822) of GUID type "2E54B353-1271-4842-806F-E436D6AF6985" Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-06-04sifive: fu540: Add U-Boot proper sector startJagan Teki
Add U-Boot proper sector start offset for SiFive FU540. This value is based on the partition layout supported by SiFive FU540. u-boot.itb need to write on this specific offset so-that the SPL will retrieve it from here and load. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
2020-06-04sifive: fu540: Add sample SD gpt partition layoutJagan Teki
This is a sample GPT partition layout for SD card, right now three important partitions are added to make the system bootable. partition layout: Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000022 0x00000821 "loader1" attrs: 0x0000000000000000 type: 5b193300-fc78-40cd-8002-e86c45580b47 guid: cbcbef44-e627-42bc-b134-93b6f3784b8c 2 0x00000822 0x00002821 "loader2" attrs: 0x0000000000000000 type: 2e54b353-1271-4842-806f-e436d6af6985 guid: f54eba28-d8de-4852-978d-1a673777e2ae 3 0x00002822 0x00020821 "rootfs" attrs: 0x0000000000000004 type: 0fc63daf-8483-4772-8e79-3d69d8477de4 type: linux guid: 9561df46-8d55-4799-a83b-cfee9ef6ff93 Note: - loader1 would be fsbl or spl - loader2 would be U-Boot or U-Boot proper Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
2020-06-04riscv: sifive: fu540: add SPL configurationPragnesh Patel
Add a support for SPL which will boot from L2 LIM (0x0800_0000) and then SPL will boot U-Boot FIT image (OpenSBI FW_DYNAMIC + u-boot.bin) from MMC boot devices. SPL related code is leveraged from FSBL (https://github.com/sifive/freedom-u540-c000-bootloader.git) Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-04riscv: cpu: fu540: Add support for cpu fu540Pragnesh Patel
Add SiFive fu540 cpu to support RISC-V arch Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-04riscv: dts: sifive: Sync hifive-unleashed-a00 dts from linuxPragnesh Patel
This sync has changes required to use GPIO in U-Boot and U-Boot SPL. Sync dts from linux v5.7-rc2 commit: "riscv: dts: Add GPIO reboot method to HiFive Unleashed DTS file" (sha1: 0a91330b2af9f71ceeeed483f92774182b58f6d9) Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-04riscv: sifive: dts: fu540: set ethernet clock ratePragnesh Patel
Set ethernet clock rate to 125 Mhz so that it will work with 1000Mbps, Earlier this is done by FSBL. With this change We can remove the ethernet clock rate code from FSBL. Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2020-06-04clk: sifive: fu540-prci: Release ethernet clock resetPragnesh Patel
U-Boot ethernet works with FSBL flow where releasing ethernet clock reset is part of FSBL itself but with the SPL, We need to release ethernet clock reset explicitly for U-Boot proper. With this change Release ethernet clock reset code in FSBL might not be needed or unaffected. Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2020-06-04clk: sifive: fu540-prci: Add ddr clock initializationPragnesh Patel
Release ddr clock reset once clock is initialized Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-04clk: sifive: fu540-prci: Add clock enable and disable opsPragnesh Patel
Added clock enable and disable functions in prci ops Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-09-21 11:45:17 +0000