aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-11-13sun6i: Add cpucfg register definitionsHans de Goede
Not used atm, for future use (e.g. PSCI). Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13sun6i: Add clock functions needed for SPL / DRAM initHans de Goede
Add clock_init_safe and clockset_pll5 functions, as these are needed for SPL support resp. DRAM init (which is needed for SPL too). Also add some extra clock register constant defines. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13sun6i: Add basic axp221 driverOliver Schinagl
The A31 uses the AXP221 pmic for various voltages. Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> -- Changes in v2: -Rebase Changes in v3: -Add support for all dldo and aldo-s -Add Kconfig option to select building AXP221 and to select voltage of dldo and aldo-s Changes in v4: -Add axp221_setbits helper function -Use symbolic names for enabled bits in CTRL1 - CTRL3 registers
2014-11-13sun6i: Add new p2wi controller driverOliver Schinagl
The A31 uses a new push-pull two wire interface, which features higher transfer speeds (upto 6 MHz) in theory. While the hardware can burst 8 bytes each time, this driver will only see very little use and thus is limited to single byte transmission only. Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13zynq: zybo: Move CONFIG_DEFAULT_DEVICE_TREE to defconfigMichal Simek
This is a MIME GnuPG-signed message. If you see this text, it means that your E-mail or Usenet software does not support MIME signed messages. The Internet standard for MIME PGP messages, RFC 2015, was published in 1996. To open this message correctly you will need to install E-mail or Usenet software that supports modern Internet standards. Move CONFIG_DEFAULT_DEVICE_TREE from board config directly to defconfig. This patch removes compilation warning: include/configs/zynq_zybo.h:24:0: warning: "CONFIG_DEFAULT_DEVICE_TREE" redefined [enabled by default] #define CONFIG_DEFAULT_DEVICE_TREE zynq-zybo Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-11-13Merge branch 'zynq' of git://www.denx.de/git/u-boot-microblazeTom Rini
2014-11-13kconfig: arm: move "armv8" define to arch/arm/KconfigMasahiro Yamada
Commit 2e07c249a67e (kconfig: arm: introduce symbol for ARM CPUs) collected the default values of CONFIG_SYS_CPU into arch/arm/Kconfig. This commit moves "armv8" to there for consistency. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Georges Savoundararadj <savoundg@gmail.com>
2014-11-13kconfig: arm: select CPU_V7 for some new boardsMasahiro Yamada
This commit adds "select CPU_V7" for some new boards that were not covered by commit 2e07c249a67e (kconfig: arm: introduce symbol for ARM CPUs). Redundant "SYS_CPU" defines and "string" directives should be removed. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Georges Savoundararadj <savoundg@gmail.com>
2014-11-13ARM: remove unused CPU directoryMasahiro Yamada
There is no board with CPU "arm_intcm". Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2014-11-13sh: define CONFIG_CPU_SH4A for some boardsMasahiro Yamada
Precisely, these boards are SH4A rather than SH4. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-11-13sh: consolidate CONFIG_SYS_CPU definesMasahiro Yamada
Now each board selects one of CONFIG_CPU_SH2, CONFIG_CPU_SH3, CONFIG_CPU_SH4, so let's move CONFIG_SYS_CPU definition to arch/sh/Kconfig. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-11-13sh: move CONFIG_{SH2, SH2A, SH3, SH4} to KconfigMasahiro Yamada
This commit moves CONFIG_SH2, CONFIG_SH2A, CONFIG_SH3, CONFIG_SH4 to Kconfig renaming into CONFIG_CPU_SH2, CONFIG_CPU_SH2A, CONFIG_CPU_SH3, CONFIG_CPU_SH4, respectively because arch/sh/Kconfig of Linux uses CONFIG_CPU_SH* convention. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-11-13sh: use more descriptive prompts for board select menuMasahiro Yamada
The current prompts were added by a conversion tool based on board directory names when switching to Kconfig. Use better prompts mostly taken from from arch/sh/boards/* of Linux Kernel. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-11-12kbuild: Make scripts executableMasahiro Yamada
The Makefiles call the respective interpreter explicitly, but this makes it easier to use the scripts manually. (This commit follows commit 06ed5c2bfaca of Linux Kernel) Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12powerpc: remove orphaned boards mcc200 and prs200Nikita Kiryanov
mcc200 and prs200 are old and have no maintainer. Remove the boards. This also removes the mcc200 specific 1bpp BMP support from common/lcd.c Cc: Wolfgang Denk <wd@denx.de> Cc: Anatolij Gustschin <agust@denx.de> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: York Sun <yorksun@freescale.com> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-11-12km_arm: convert the km_arm boards to the generic board supportValentin Longchamp
This implies that all the km_kirkwood boards and their variants now are using the generic board init sequence. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-11-12mx28evk: README: Revision C is also supportedFabio Estevam
Adjust the text to mention that rev C of the board is also supported. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-11-12arm: imx: make bmode command work with SPL/U-Boot comboNikita Kiryanov
The bmode command forces the SoC to use a specific boot device by writing its boot mode into SRC_GPR9, and notifying the SoC of the change using SRC_GPR10[28] bit: if the bit is on, bootROM uses the value in SRC_GPR9 instead of SRC_SMBR1 to determine the boot device. SPL on the other hand is oblivious to this distinction, so once the bootROM loads SPL from the device configured in SRC_GPR10, SPL will attempt to load U-Boot from the device configured in SRC_SMBR1, which is not updated by the bootROM to the value in SRC_GPR9. The result is that the selected boot device is not used across all the boot stages. Update spl_boot_device() to look at gpr9 when necessary. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Troy Kisky <troy.kisky@boundarydevices.com> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Heiko Schocher <hs@denx.de>
2014-11-12malloc: Output region when debuggingThierry Reding
When DEBUG is set, output memory region used for malloc(). Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-11-12ARM: cache-cp15: Use more accurate typesThierry Reding
size_t is the canonical type to represent variables that contain a size. Use it instead of signed integer. Physical addresses can be larger than 32-bit, so use a more appropriate type for them as well. phys_addr_t is a type that is 32-bit on systems that use 32-bit addresses and 64-bit if the system is 64-bit or uses a form of physical address extension to use a larger address space on 32-bit systems. Using these types the same API can be implemented on a wider range of systems. Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-11-12ARM: cache_v7: Various minor cleanupsThierry Reding
Remove two gratuituous blank lines, uses u32 (instead of int) as the type for values that will be written to a register, moves the beginning of the variable declaration section to a separate line (rather than the one with the opening brace) and keeps the function signature on a single line where possible. Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-11-11Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2014-11-11Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
2014-11-11Merge branch 'master' of git://git.denx.de/u-boot-uniphierTom Rini
2014-11-11Revert "lib: bootm: add missing include"Michal Simek
This is a MIME GnuPG-signed message. If you see this text, it means that your E-mail or Usenet software does not support MIME signed messages. The Internet standard for MIME PGP messages, RFC 2015, was published in 1996. To open this message correctly you will need to install E-mail or Usenet software that supports modern Internet standards. This reverts commit 1e96220a5687efae2aed45ce56e143336c40d0a7. Remove duplicated vxworks.h header. The same change was done by "ARM: prevent compiler warnings from bootm.c" (sha1: 8d196e52b58d1e50a80c2f5067b201cda521c75c) Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-11-12ARM: UniPhier: call pin_init() also in the normal bootMasahiro Yamada
CONFIG_UNIPHIER_SERIAL has been moved to Kconfig and it is defined in ./.config but not in spl/.config, so pin_init() should be called from the normal image so that UART works correctly. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12ARM: UniPhier: consolidate board_postclk_init() functionMasahiro Yamada
This commit merges arch/arm/cpu/armv7/uniphier/ph1-*/board_postclk_init.c to arch/arm/cpu/armv7/uniphier/board_postclk_init.c Because PH1-Pro4 does not have the BCU block, add __weak to bcu_init(). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12ARM: UniPhier: decrease pre-reloc malloc area sizeMasahiro Yamada
In the current implementation of the boot sequence of UniPhier platform, 32KB temporary RAM is available before relocation. The malloc area and the stack shares the 32KB area. With CONFIG_SYS_MALLOC_F_LEN set to 0x7000 (28KB), only 0x1000 (4KB) is left for the stack. In some use cases, the system hangs up with stack over-flow. Even with driver-model UART enabled, the malloc area of 0x2000 (8KB) should be enough. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12ARM: UniPhier: add set_pinsel macro for use in assembly codeMasahiro Yamada
The function sg_set_pinsel is useful for switching I/O pins but it can be only used in C code. This commit adds a simple macro that is available in asm code. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12ARM: UniPhier: enable USB featuresMasahiro Yamada
FAT-formated USB storage device access is available. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12usb: UniPhier: add UniPhier on-chip EHCI host driver supportMasahiro Yamada
Support EHCI host driver used on Panasonic UniPhier platform. Since Device Tree is not supported on UniPhier yet, the base address of USB cores are passed from board files (platdevice.c). TODO for me: Move the base address to device trees. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Marek Vasut <marex@denx.de>
2014-11-12ARM: UniPhier: add MIO register fileMasahiro Yamada
This commit adds register defines of MIO (Media I/O) block of UniPhier platform. This file is necessary to control the reset signals of the USB cores. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12usb: add basic USB configs in KconfigMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Marek Vasut <marex@denx.de>
2014-11-12ARM: UniPhier: add EHCI host pin settings for PH1-Pro4Masahiro Yamada
These IO pins are necessary for port power control and over current detect. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12ARM: UniPhier: move DDR related configuration to KconfigMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12ARM: UniPhier: reset on-board devices on start-upMasahiro Yamada
If a support card is attached to the main board, the on-board SMSC9118 LAN controller is available. It must be kept in reset state for a while on start-up. When the board is kicked via a debbuger rather than pushing the hardware reset button, on-board chips are not reset; in this case the reset signals should be asserted by software. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-12serial: UniPhier: borrow macros from linux/serial_reg.hMasahiro Yamada
The same bit-field macros are defined in include/linux/serial_reg.h so let's include it and delete duplicated defines. Also, remove unnecessary inclusion of <common.h>. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-11kconfig: zynq: Add ZYBO boardPeter Crosthwaite
Add a defconfig and Kconfigury for the Digilent ZYBO board. Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com> Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-11-11configs: zynq: Add config support for ZYBOTinghui Wang
This patch adds config support needed for ZYBO target and has been tested on Rev. B ZYBO hardware. Signed-off-by: Tinghui Wang <steven.wang@digilentinc.com> [PC changes: * Dropped boards.cfg change (rebase conflict) * Dropped custom u-boot env * Added DTS * Misc forward-porting changes ] Signed-off-by: Peter Crosthwiate <crosthwaite.peter@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-11-11arm: dts: zynq: Add digilent ZYBO board dtsPeter Crosthwaite
It's a Zynq board similar in design to the currently supported ones. 512MB of RAM and UART1 is used. Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com> Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-11-11zynq: Use GPLed files for SPLSoren Brinkmann
The latest Xilinx tools generate ps7_init files that are explicitly available under GPL. Change the makefile to allow drop in of those files for building the SPL. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Reviewed-and-tested-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-11-10Prepare v2015.01-rc1Tom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2014-11-10Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
2014-11-10Merge branch 'master' of git://git.denx.de/u-boot-blackfinTom Rini
2014-11-10Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2014-11-10Added support for comments in input to mkenvimage.Dominik Muth
This patch adds support for comments in the input to mkenvimage, i.e. in the environment source: All lines starting with a # in the firs column will be ignored. Additionally empty lines will also be ignored. Signed-off-by: Dominik Muth <dominik.muth@bkvibro.com>
2014-11-10ZFS: Clean up cppcheck warnings where relevant, leaked memory etcJorgen Lundman
In a message from Wolfgang Denk highlighting warnings from cppcheck, the patch will address those that are correctly diagnosed. Some are false-positives: > [fs/zfs/zfs.c:937]: (error) Memory leak: l dmu_read() allocates "l" if successful, so error-case should not free it. > [fs/zfs/zfs.c:1141]: (error) Memory leak: dnbuf dmu_read() allocates "dnbuf" if successful, so error-case should not free it. > [fs/zfs/zfs.c:1372]: (error) Memory leak: osp zio_read() allocates "osp" if successful, so error-case should not free it. > [fs/zfs/zfs.c:1726]: (error) Memory leak: nvlist int_zfs_fetch_nvlist() allocates "nvlist" if successful, so error-case should not free it. Signed-off-by: Jorgen Lundman <lundman@lundman.net>
2014-11-10board/esd/common/auto_update.c: fix Uninitialized variableWolfgang Denk
cppcheck reports: [board/esd/common/auto_update.c:458]: (error) Uninitialized variable: cnt The variable is not really used anywhere, so remove it. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2014-11-10ARM: MXS: fix Uninitialized variable errorWolfgang Denk
cppcheck reports: [arch/arm/cpu/arm926ejs/mxs/timer.c:96]: (error) Uninitialized variable: now Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-11-10arm: rmobile: alt: Change clock of SCIF to external clockNobuhiro Iwamatsu
Change clock of SCIF for Alt board is used to external clock. This changes to using external clock. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-11 03:29:02 +0000