| Age | Commit message (Collapse) | Author |
|---|
|
Add support for XTX XT26G0xA and XT26xxxD. The driver is ported from
linux-6.7.1. This driver is tested on Banana BPI-R3 with XT26G01A and
XT26G12D.
Link: https://lore.kernel.org/all/20240312014314.15454-1-bruce_suen@163.com
Signed-off-by: Bruce Suen <bruce_suen@163.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
Introduced with commit 6a8dfd57220d ("nand: atmel: Add DM based NAND
driver") when driver was initially ported from Linux. The context
around this and especially the code itself suggests 'read' is meant
instead of write.
The fix is the same as accepted in Linux already with mainline Linux
kernel commit 1c60e027ffde ("mtd: nand: raw: atmel: Fix comment in
timings preparation").
Link: https://lore.kernel.org/all/20240320090214.40465-6-ada@thorsis.com
Link: https://lore.kernel.org/linux-mtd/20240307172835.3453880-1-miquel.raynal@bootlin.com/T/#t
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
One tab in general. One tab plus two spaces for help text.
Link: https://lore.kernel.org/all/20240320090214.40465-4-ada@thorsis.com
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
Introduced in upstream Linux with commit 7a08dbaedd365 for release v5.0.
When the new atmel nand driver was backported to U-Boot with commit
6a8dfd57220d ("nand: atmel: Add DM based NAND driver") that definition
was added to the driver instead of the header file. Move it over to the
other definitions with the same help text it has in Linux.
Code actually using this has not been ported over to raw nand base yet.
Link: https://lore.kernel.org/all/20240320090214.40465-3-ada@thorsis.com
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
In every other place in this file the macro is used, make it consistent.
Link: https://lore.kernel.org/all/20240320090214.40465-2-ada@thorsis.com
Fixes: 9d1806fadc24 ("mtd: nand: Get rid of mtd variable in function calls")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
Basic support for Amlogic Meson NAND controller on AXG. This version
works at only first EDO mode.
Based on Linux version 6.7.0-rc4.
Link: https://lore.kernel.org/all/20240210223927.570043-1-avkrasnov@salutedevices.com
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
Handle the return value of spi_flash_probe_bus_cs() to avoid sf probe
crashes.
Link: https://lore.kernel.org/all/20240104114619.280513-1-o451686892@gmail.com
Signed-off-by: Weizhao Ouyang <o451686892@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2024-07-rc1-2
Documentation:
* bump build dependency idna to 3.7
* update docker image reference to latest
* fix section levels in gen_compile_commands
* fix references to trace doc
UEFI:
* eliminate duplicate runtime section definitions
* let 'EFI using ACPI tables at' be a debug message
* sanitize efi_tcg2_final_events_table definition
* move efi_var_collect to common functions
* improve error messages in variables unit test by using
EFI_UNSUPPORTED for private authenticated variables
|
|
While we unlikely to have an issue with CVE-2024-3651, it is simple
enough to bump our version of idna to receive the fix, do so.
Reported-by: GitHub dependabot
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
The README.trace has been moved and converted to rst in commit dce26c7d56ed
("doc: move README.trace to HTML documentation"); fix all the remaining
references to this file.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
The length of the variable name typically is not 1.
Neither the length of the variable name nor the size of the appended
data is known in the include.
* Define the size of element variable_name as variable.
* Remove the unusable element variable_data.
Addresses-Coverity-ID: 467400 Out-of-bounds read
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
Improve error message for UEFI SCT tests.
Signed-off-by: Weizhao Ouyang <o451686892@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
The message "EFI using ACPI tables at %lx\n" is only of interest when
debugging. Make it a debug message.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
The following symbols are defined in two includes:
* __efi_runtime_start[]
* __efi_runtime_stop[]
* __efi_runtime_rel_start[]
* __efi_runtime_rel_stop[]
Eliminate the definitions in efi_loader.h.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
efi_var_collect() was initially placed in efi_var_file.c, since back
then we only supported efi variables stored in a file. Since then we
support variables stored in an RPMB as well and use that function to
collect variables that should be present at runtime.
So let's move it around in efi_var_common.c which makes more sense
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Ilias Apalodimas <apalos@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
The 2 subsections of this page ("Compatible IDEs" and "Usage") are using
the same header level as the title (with "===").
Because of this, they always appear in the HTML rendered ToC.
Drop the subsections one level lower by replacing "=" by "-".
This fixes the HTML rendering.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
commit cacc0b2678c0 ("CI: Move to latest container image") updated the
docker container image.
Reflect the change in the documentation.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Eugene Uriev <eugeneuriev@gmail.com> says:
There was no "mcheck" for U-Boot before.
Since U-Boot has only 1 thread, and normally makes 4000+ - 6000+
mallocs, it's better to use havier canaries to protect heap-chunks.
My variant uses 2x8 = 16byte-long protector. And
the multiplier could be changed to tune speed/protection tradeoff.
This protects not only against memset()-s, but against "near" wild
pointers too, and makes more probable to catch "distant" ones.
The core file of the set is included into the C-file, not complied
separately in order to enable (potential) coexisting of
mcheck-protectors, e.g. malloc_simple(.) and dlmalloc simultaneously.
My tests were for ARM SoC, 64bit, so the patch is
aware of alignment.
Primary this patch is for using by developers: to verify,
if a change doesn't break the heap integrity.
By default the mcheck is disabled and wouldn't affect the boot.
I used pedantic mode, canary=16byte, registry-size=6608.
For my system the overhead was 230ms.
|
|
Signed-off-by: Eugene Uriev <eugeneuriev@gmail.com>
|
|
My tests have been run on an U-Boot (of older version)
for ARM (64bits).
Signed-off-by: Eugene Uriev <eugeneuriev@gmail.com>
|
|
The using of pre-reloc/malloc_simple heap is
too hard to follow after the relocation.
So lets drop it from the pedantic registry
and switch to dlmalloc, when moved.
The offset is ignored, but kept in the API
for the probable case, when that early
heap is relocated too.
Signed-off-by: Eugene Uriev <eugeneuriev@gmail.com>
|
|
The pedantic mode is run-time contolled, so
appropriate registry take place everytime.
Maybe it's worth to use compile-time control only.
So, the registry could be optimized out by an #ifdef.
Signed-off-by: Eugene Uriev <eugeneuriev@gmail.com>
|
|
Signed-off-by: Eugene Uriev <eugeneuriev@gmail.com>
|
|
This changes are probable worth to be generalized in a
separate .h-file so, making it able to cover
libc-mallocs and others, without too much copy-paste.
But the malloc<=>mALLOc substitutions interfere
with an elegant way to do this.
Signed-off-by: Eugene Uriev <eugeneuriev@gmail.com>
|
|
The core part of mcheck, but without memalign.
memalign - to be added in ensuing commits.
Signed-off-by: Eugene Uriev <eugeneuriev@gmail.com>
|
|
These fast helpers sometimes breach mem-chunk boundaries.
Thus they trigger mcheck alarm. Standard ones are accurate though.
Signed-off-by: Eugene Uriev <eugeneuriev@gmail.com>
|
|
Signed-off-by: Eugene Uriev <eugeneuriev@gmail.com>
|
|
Allowing multicast packets is required for IPv6 neighbor discovery
protocol.
Signed-off-by: Parvathi Bhogaraju <pbhogaraju@microsoft.com>
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
|
|
In IPv6 context, the ICMP and UDP checksum byte in the RX packet
is initially set to 0, recaclculated, and then re-inserted.
This process can result in a dirty cache line. To prevent issues,
it is essential to invalidate cache for the RX buffer before freeing
the descriptor for next DMA transfer.
This ensure that the dirty cache line doesn't inadvertently written back
due to cache eviction, there by corrupting the RX buffer
Signed-off-by: Parvathi Bhogaraju <pbhogaraju@microsoft.com>
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
|
|
Fix compilation warning:
../arch/arm/include/asm/io.h: In function 'eqos_free_pkt':
../arch/arm/include/asm/io.h:103:32: warning: 'rx_desc' may be used uninitialized [-Wmaybe-uninitialized]
103 | #define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
| ^~~
../drivers/net/dwc_eth_qos.c:1220:27: note: 'rx_desc' was declared here
1220 | struct eqos_desc *rx_desc;
| ^~~~~~~
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
MD Danish Anwar <danishanwar@ti.com> says:
Introduce ICSSG PRUETH support in uboot. The ICSSG driver is used in TI
AM654 SR2.0.
The ICSSG PRU Sub-system runs on EMAC firmware. This series Introduces
support for ICSSG driver in uboot.
This series has been tested on AM65x SR2.0, and the ICSSG interface is
able to ping / dhcp and boot kernel using tftp in uboot.
To use ICSSG2 ethernet, the ICSSG firmware needs to be loaded to PRU RPROC
cores and RPROC cores need to be booted with the firmware. This step is
done inside driver similar to kernel.
The remoteproc driver uses request_fw_into_buf() API from fs-loader driver
to load and start rproc with the required firmwares.
This series only introduces driver files. The device tree and config
changes to enable ICSSG driver will be introduced later.
|
|
ICSSG firmware supports FDB commands. Add support to send FDB commands
from driver. Once rx_flow_id is obtained from dma, let firmware know that
we are using this rx_flow_id by sending a FDB command.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
|
|
This is the PRUSS Ethernet driver for TI AM654 SR2.0 and later SoCs with
the ICSSG PRU Sub-system running EMAC firmware. ICSSG Subsystem supports
two slices per instance. This driver caters to both slices / ports of
the icssg subsystem.
Since it is not possible for Ethernet driver to register more than one
port for a given instance, this patch introduces top level PRUETH as
UCLASS_MISC and binds UCLASS_ETH to individual ports in order to support
bringing up more than one Ethernet interface in U-Boot.
Since top level driver is UCLASS_MISC, board files would need to
instantiate the driver explicitly.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
|
|
Add icssg_queue.c file. This file introduces macros and APIs related to
ICSSG queues. These will be used by ICSSG Ethernet driver.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
|
|
Add icssg_config.h / .c and icssg_classifier.c files. These are firmware
configuration and classification related files. Add MII helper APIs and
MACROs. These APIs and MACROs will be later used by ICSSG Ethernet driver.
Also introduce icssg_prueth.h which has definition of prueth related
structures.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
|
|
Add firmware interface related headers and macros for ICSSG Ethernet
driver. These macros will be later used by the ICSSG ethernet driver.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
|
|
Michal Simek <michal.simek@amd.com> says:
It looks like that only CVE-2016-9841 is not fixed and this series is
trying to address it. The first two patches are just preparation based on
changes which happened in past. The third one is actual fix and the last
one is following what has been done in Linux kernel long time ago and don't
use incorrect zlib version string.
I tested it with and I can't see any issue.
./test/py/test.py --bd sandbox --build -s
And gitlab CI is also not showing any issue.
|
|
Get rid of zlib version which is not correct because of U-Boot related
changes and various CVE backports.
The change in inspired by Linux kernel commit 4f3865fb57a0 ("[PATCH]
zlib_inflate: Upgrade library code to a recent version") which described
ZLIB_VERSION removal as
"This patch also removes ZLIB_VERSION as it no longer has a correct value.
We don't need version checks anyway as the kernel's module handling will
take care of that for us. This removal is also more in keeping with the
zlib author's wishes (http://www.zlib.net/zlib_faq.html#faq24) and I've
added something to the zlib.h header to note its a modified version."
Author describes wish to follow this guidance at
https://www.zlib.net/zlib_faq.html#faq24:
"The license says that altered source versions must be "plainly marked". So
what exactly do I need to do to meet that requirement?
You need to change the ZLIB_VERSION and ZLIB_VERNUM #defines in zlib.h. In
particular, the final version number needs to be changed to f, and an
identification string should be appended to ZLIB_VERSION. Version numbers
x.x.x.f are reserved for modifications to zlib by others than the zlib
maintainers. For example, if the version of the base zlib you are altering
is 1.2.3.4, then in zlib.h you should change ZLIB_VERNUM to 0x123f, and
ZLIB_VERSION to something like 1.2.3.f-zachary-mods-v3. You can also update
the version strings in deflate.c and inftrees.c."
But U-Boot is not exact version that's why following the same style which
has been used by Linux kernel where ZLIB_VERSION is completely removed.
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
The patch corresponds to zlib commit at
https://github.com/madler/zlib/commit/9aaec95e82117c1cb0f9624264c3618fc380cecb
which declares that it is fixing CVE-2016-9841.
Here is c&p description from zlib:
"Use post-increment only in inffast.c.
An old inffast.c optimization turns out to not be optimal anymore
with modern compilers, and furthermore was not compliant with the
C standard, for which decrementing a pointer before its allocated
memory is undefined. Per the recommendation of a security audit of
the zlib code by Trail of Bits and TrustInSoft, in support of the
Mozilla Foundation, this "optimization" was removed, in order to
avoid the possibility of undefined behavior."
Origin patch also updates the code when
INFLATE_ALLOW_INVALID_DISTANCE_TOOFAR_ARRR is present but this code is not
the part of U-Boot hence it is ignored.
Also do not deal with state->sane variable which requires other changes
which are also not the part of zlib.
Commit 92faa8b10918 ("zlib: handle overflow while calculating available
stream input size") is kept in inffast.c too not to break described case.
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
There is no particular patch/description which described the reason for
this change but it was done as the part of zlib 1.2.3.5 release done by
zlib commit d004b047838a ("zlib 1.2.3.5"). It is preparation for followup
patch.
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
There is no particular patch/description which described the reason for
this change but it was done as the part of zlib 1.2.3.5 release done by
zlib commit 639be997883d ("zlib 1.2.3.3") It is preparation for followup
patch.
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
- Assorted sandbox fixes, cleanup some of the partition table code and a
few other fixes
|
|
The function uniphier_mem_map_init() is to change global variable
'mem_map', which is referenced to get_page_table_size() to calculate
the size of page table.
However, uniphier_mem_map_init() is called after get_page_table_size(),
so the size of page table and 'mem_map' become inconsist each other.
After all, U-Boot fails to boot on chip with memory map different from
default map,
uniphier_mem_map_init() should be moved to dram_init(), which is
called before get_page_table_size().
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
|
|
Using uclass_get_name() reduces the code size.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
load_entry_point is not used.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
When "memory" node is being processed in fdt_pack_reg() on ARM64
platforms, an unaligned bus access might happen, which leads to
"synchronous abort" CPU exception. Consider next dts example:
/ {
#address-cells = <2>;
#size-cells = <1>;
memory@80000000 {
device_type = "memory";
reg = <0x0 0x80000000 0x3ab00000>,
<0x0 0xc0000000 0x40000000>,
<0x8 0x80000000 0x80000000>;
};
};
After fdt_pack_reg() reads the first addr/size entry from such memory
node, the "p" pointer becomes 12 bytes shifted from its original value
(8 bytes for two address cells + 4 bytes for one size cell). So now it's
not 64-bit aligned, and an attempt to do 64-bit bus access to that
address will cause an abort like this:
"Synchronous Abort" handler, esr 0x96000021, far 0xba235efc
This issue was originally reported by David Virag [1] who observed it
happening on Samsung Exynos7885 SoC (ARM64), and later the same issue
was observed on Samsung Exynos850 (ARM64).
Fix the issue by using put_unaligned_be64() helper, which takes care of
possible unaligned 64-bit accesses. That solution was proposed by Simon
Glass in the original thread [1].
[1] https://lists.denx.de/pipermail/u-boot/2023-July/522074.html
Fixes: 739a01ed8e02 ("fdt_support: fix an endian bug of fdt_fixup_memory_banks")
Suggested-by: Simon Glass <sjg@google.com>
Reported-by: David Virag <virag.david003@gmail.com>
Closes: https://lists.denx.de/pipermail/u-boot/2023-July/522074.html
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
We may enter the command line interface in a state where on the remote
console the cursor is not shown. Send an escape sequence to enable it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
In part_get_info_by_name() the inability to get some partition info
shouldn't be a reason for dropping out of the loop. That might happen
e.g. if the partition is hidden or unused. An example of such case are
Samsung devices, where they use the "unused" GUID type
(00000000-0000-0000-0000-000000000000) to indicate that the partition
should be hidden from the OS. Such partitions might not be seen in
"part list" output, which creates "gaps" in numbering in between of the
visible partitions:
Part Start LBA End LBA Name
1 0x00000400 0x0000a3ff "efs"
5 0x00026420 0x00026c1f "dtbo"
12 0x0003f390 0x0074738f "super"
In that case, the loop in part_get_info_by_name() would break after
partition #1, so any attempt to obtain "dtbo" or "super" partition will
fail. Fix that by continuing to iterate over the remaining partitions to
make sure none of the visible ones is missed. That makes "part" command
(e.g. "part start", "part size") able to work with such tables.
Fixes: 87b8530fe244 ("disk: part: implement generic function part_get_info_by_name()")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
A recent refactoring in image-host.c messed up the return values of
the function that reads the encryptiong keys. This patch fixes this
and also makes sure that error output goes to stderr instead of to
stdout.
Signed-off-by: Hugo Cornelis <hugo.cornelis@essensium.com>
|
|
Mentions that command line option --signal is needed to make use of this
configuration option.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
