aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2022-01-08udoo: Increase CONFIG_ENV_OFFSETFabio Estevam
Increase CONFIG_ENV_OFFSET to avoid the environment region to overlap with U-Boot proper. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
2022-01-08udoo: Adjust the SD card device numberingFabio Estevam
After the conversion to DM the SD card shows up as 'mmc 2' device. Adjust the 'mmcdev' and the distro command 'func' accordingly. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
2022-01-08udoo: Call gpio_request()Fabio Estevam
Calling gpio_request() prior to its usage is now mandatory. This fixes the following GPIO errors: U-Boot SPL 2022.01-rc3-00067-g7a5be871c0ec (Dec 18 2021 - 17:45:07 -0300) Trying to boot from MMC1 U-Boot 2022.01-rc3-00067-g7a5be871c0ec (Dec 18 2021 - 17:45:07 -0300) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: WDOG Model: Udoo i.MX6 Quad Board Board: Udoo Quad DRAM: 1 GiB MMC: FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial gpio@20a0000: set_dir_flags: error: gpio GPIO2_31 not reserved gpio@20a4000: set_dir_flags: error: gpio GPIO3_23 not reserved gpio@20b0000: set_dir_flags: error: gpio GPIO6_24 not reserved gpio@20b0000: set_dir_flags: error: gpio GPIO6_25 not reserved gpio@20b0000: set_dir_flags: error: gpio GPIO6_27 not reserved gpio@20b0000: set_dir_flags: error: gpio GPIO6_28 not reserved gpio@20b0000: set_dir_flags: error: gpio GPIO6_29 not reserved gpio@20a4000: set_value: error: gpio GPIO3_23 not reserved Net: Could not get PHY for FEC0: addr -2 No ethernet found. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
2022-01-08ARM: dts: imx6qdl-udoo: Properly describe the SD card detectFabio Estevam
GPIO7_IO00 is used as SD card detect. Properly describe this in the devicetree. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2022-01-08udoo_spl: Initialize the eSDHC controller in SPLFabio Estevam
Currently, imx6q udoo board fails to boot like this: U-Boot SPL 2022.01-rc3-00061-g95ca715adad3 (Dec 18 2021 - 18:04:40 -0300) Trying to boot from MMC1 The reason is that the eSDHC controller is not initialized in SPL. Initialize the eSDHC controller in SPL via C code as DM is not used in SPL. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
2022-01-07Merge branch '2022-01-07-imx8-and-buildman-updates'Tom Rini
- A large number of updates for i.MX8 platforms. We update buildman / binman to be able to fake binaries if needed, for CI, and tell the user the binary won't work. Update platforms to build again with these changes.
2022-01-07imx: imx8mm: imx8mm-kontron-n801x-s: Fix binman errorAdam Ford
The binman node is part of the imx8mm-u-boot.dtsi file which is duplicated in imx8mm-kontron-n801x-s-u-boot.dtsi and causes a build error. Remove the duplicate. Fixes: 3cbb31f0e848 ("arm64: dts: imx8mm: use common binman configuration") Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2022-01-07board: phytec: imx8mm-phycore: Remove duplicate binman nodeAdam Ford
The binman node is part of the imx8mm-u-boot.dtsi file which is duplicated in phycore-imx8mm-u-boot.dtsi and causes a build error. Remove the duplicate. Fixes: 3cbb31f0e848 ("arm64: dts: imx8mm: use common binman configuration") Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2022-01-07imx8mm_venice: switch to use binman to pack imagesTim Harvey
Use binman to pack images. Note that imx8mm_venice supports several boards via multiple DTB's thus in the fit node we must use: - fit,fdt-list = "of-list" - fdt-SEQ - config-SEQ Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2022-01-07arm64: dts: imx8mm-u-boot.dtsi: improve odd blob-ext namingMarcel Ziswiler
Rather than using odd implicit blob-ext naming, explicitly specify the type to be of blob-ext and therefore also simplify the node naming. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2022-01-07arm64: dts: imx8mm-u-boot.dtsi: explicitly add spl filenameMarcel Ziswiler
Explicitly add SPL aka u-boot-spl.bin filename. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2022-01-07arm64: dts: imx8mm-u-boot.dtsi: alphabetically re-order propertiesMarcel Ziswiler
Alphabetically re-order properties. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2022-01-07arm64: dts: imx8mm: use common binman configurationMarcel Ziswiler
With the move to using binman to generate SPL aka u-boot-spl-ddr.bin and U-Boot proper aka u-boot.itb every board now covers such configuration in its own U-Boot specific device tree include. Move the comon part of that configuration to the common imx8mm-u-boot.dtsi include file. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2022-01-07arm64: dts: imx8mm-cl-iot-gate-u-boot.dtsi: use common imx8mm-u-boot.dtsiMarcel Ziswiler
Use common imx8mm-u-boot.dtsi. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2022-01-07arm64: dts: imx8mm-cl-iot-gate-u-boot.dtsi: alphabetically re-orderMarcel Ziswiler
Alphabetically re-order nodes and properties. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2022-01-07imx8mm-cl-iot-gate: fix imximage intermediate binary namingMarcel Ziswiler
This fixes the following build time issue: ... BINMAN all binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000 ./mkimage-out.spl.mkimage': mkimage.flash.mkimage: Can't open: No such file or directory make: *** [Makefile:1094: all] Error 1 Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2022-01-07doc: imx8mq_evk: update doc after using binmanPeng Fan
Update doc after using binman to pack images Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-01-07imx: imx8mq use common imximage.cfgPeng Fan
After all these board switch to binman, we could use common imximage.cfg Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Patrick Wildt <patrick@blueri.se>
2022-01-07imx: pico-imx8mq: switch to use binmanPeng Fan
Switch to use binman to pack images Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Patrick Wildt <patrick@blueri.se>
2022-01-07imx: imx8mq_phanbell: switch to binmanPeng Fan
Switch to binman to pack images Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Patrick Wildt <patrick@blueri.se>
2022-01-07imx: imx8mq_evk: switch to binmanPeng Fan
Switch to use binman to pack images Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-01-07imx8mn_beacon_2g: Switch to binmanAdam Ford
The standard 1GB Nano was converted to binman, but the 2G version was neglected. Convert it to binman as well. Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Adam Ford <aford173@gmail.com>
2022-01-07imx8mn_beacon: Fix booting hang and switch to binmanAdam Ford
Somewhere along the line, the board stopped being able to boot. Rather than just fixing the issue, let's fix the issue and migrate to binman to eliminate a warning when using custom imx tools for generating the binary. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2022-01-07imx8mm_beacon: Switch to binman for generating imageAdam Ford
To eliminate a warning when using custom imx tools for generating a binary, use binman to generate flash.bin. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-01-07binman: add support for creating dummy files for external blobsHeiko Thiery
While converting to binman for an imx8mq board, it has been found that building in the u-boot CI fails. This is because an imx8mq requires an external binary (signed_hdmi_imx8m.bin). If this file cannot be found mkimage fails. To be able to build this board in the u-boot CI a binman option (--fake-ext-blobs) is introduced that can be switched on via the u-boot makefile option BINMAN_FAKE_EXT_BLOBS. With that the needed dummy files are created. Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-01-07Merge branch '2022-01-04-platform-updates' into nextTom Rini
- Assorted updates for vexpress64, apple m1, iot2050 and stemmy platforms.
2022-01-07Merge branch '2022-01-06-assorted-important-fixes'Tom Rini
- Revert a clk change, to enable some platforms to work again - Updates to the udoo NEO family of boards to work correctly - Fix SiFive Unleashes/Unmatched boards booting - Update rockchip maintainer entry
2022-01-07Revert "clk: Detect failure to set defaults"Marek Vasut
This reverts commit 92f1e9a4b31c0bf0f4f61ab823a6a88657323646. The aforementioned patch causes massive breakage on all platforms which have 'assigned-clock' DT property in their DT which references any clock that are not supported by the platform clock driver. That can easily happen either in SPL, or because the clock driver is reduced. Currently it seems all iMX8M are affected and fail to boot altogether. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Peng Fan <peng.fan@oss.nxp.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-01-07udoo: neo: Do not print the Model informationFabio Estevam
By default the Model information from DT is printed: CPU: Freescale i.MX6SX rev1.2 996 MHz (running at 792 MHz) CPU: Extended Commercial temperature grade (-20C to 105C) at 63C Reset cause: POR Model: UDOO Neo Basic Board: UDOO Neo FULL I2C: ready As the udoo basic DT is used, such output may be confusing. Improve it by only printing the Board model instead, which is read from the board identification GPIOs. Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Tommaso Merciai <tomm.merciai@gmail.com> Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
2022-01-07udoo: neo: Fix the board model printingFabio Estevam
Currently, the board model is not printed correctly: Board: UDOO Neo UNDEFINED Read the model type in SPL and store it the internal OCRAM, so that U-Boot proper can retrieve it correctly. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2022-01-07udoo_neo: Enable support for USB and storagePeter Robinson
Enable support for USB and USB storage on the UDOO Neo. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2022-01-07udoo_neo: Fix ethernetPeter Robinson
The ethernet has a RMII not RGMII, also needs DM_MDIO and finally initialise it later in the process as it's not needed that early on and not everything is ready so it locks up the device. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2022-01-07udoo_neo: Fixes for booting from the mSD cardPeter Robinson
This fixes booting from the mSD card from both SPL and when using it for the OS booting. It also cleans up a few mmc booting bits that are no longer needed. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2022-01-07udoo_neo: Call gpio_request()Peter Robinson
Calling gpio_request() prior to its usage is now mandatory. This fixes the following GPIO errors: gpio@20a8000: set_dir_flags: error: gpio GPIO4_16 not reserved gpio@20a8000: set_dir_flags: error: gpio GPIO4_13 not reserved gpio@20a8000: set_dir_flags: error: gpio GPIO4_0 not reserved gpio@20a8000: get_value: error: gpio GPIO4_13 not reserved gpio@20a8000: get_value: error: gpio GPIO4_0 not reserved gpio@20a0000: set_dir_flags: error: gpio GPIO2_1 not reserved gpio@20a0000: set_value: error: gpio GPIO2_1 not reserved Fixes: 191840ae99 ("ARM: imx: udoo_neo: Enable OF_CONTROL and DM gpio/pin control") Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2022-01-07riscv: sifive: Fix OF_BOARD boot failureBin Meng
When using QEMU to have a quick test of booting U-Boot S-mode payload directly without the needs of preparing the SPI flash or SD card images for SiFive Unleashed board, as per the instructions [1], it currently does not boot any more. This was caused by the OF_PRIOR_STAGE removal, as gd->fdt_blob no longer points to a valid DTB. OF_BOARD is supposed to replace OF_PRIOR_STAGE, hence we need to add the OF_BOARD logic in board_fdt_blob_setup(). [1] https://qemu.readthedocs.io/en/latest/system/riscv/sifive_u.html#running-u-boot Fixes: 2e8d2f88439d ("riscv: Remove OF_PRIOR_STAGE from RISC-V boards") Fixes: d6f8ab30a2af ("treewide: Remove OF_PRIOR_STAGE") Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-01-07rockchip: puma/lion: update MAINTAINERS fileQuentin Schulz
Philipp does not work at Theobroma Systems anymore so let's swap Philipp's address with mine. Cc: Philipp Tomsich <philipp.tomsich@vrull.eu> Cc: Quentin Schulz <foss+u-boot@0leil.net> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
2022-01-07configs: khadas-vim3{l}_android_ab: enable A/B supportMattijs Korpershoek
meson64_android.h also relies on CMD_AB_SELECT so enable that as well. Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20211122152207.219023-5-mkorpershoek@baylibre.com
2022-01-07configs: prepare khadas-vim3{l}_ab_android for AOSP supportMattijs Korpershoek
In AOSP, both VIM3 and VIM3L have 2 bootloader flavors, depending on A/B enablement. For example, for vim3l, the naming is: - u-boot_kvim3l_noab.bin : legacy support - u-boot_kvim3l_ab.bin : A/B support Prepare a defconfig to support u-boot_kvim3_ab.bin and u-boot_kvim3l_ab.bin. This is identical to khadas-vim3{l}_ab_android but will be updated in the next commit. Also update partitioning tables for A/B support. Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20211122152207.219023-4-mkorpershoek@baylibre.com
2022-01-07configs: add khadas-vim3{l}_android for AOSP supportMattijs Korpershoek
The Khadas VIM3 and VIM3L board are well supported in AOSP[1]. However, there is no mainline U-Boot support for it. The U-Boot used in AOSP is based on a vendor tree [2] Add all the necessary bits to flash and boot Android for both Khadas VIM3 and VIM3L boards. For Android instructions, refer to [1] [1] https://source.android.com/setup/build/devices#vim3_and_vim3l_boards [2] https://gitlab.com/baylibre/amlogic/atv/u-boot Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20211122152207.219023-3-mkorpershoek@baylibre.com
2022-01-07configs: meson64_android: add board specific env settingsMattijs Korpershoek
This allows us to define extra board variables, such as "board" and "board_name". Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20211122152207.219023-2-mkorpershoek@baylibre.com
2022-01-07configs: amlogic: Disable CONFIG_NET_RANDOM_ETHADDR when unnecessaryNeil Armstrong
On Meson GXL, GXM, AXG, G12A, G12B & SM1 SoCs, we can generate an unique MAC address if none valid found in the eFuses storage. Only the GXBB based boards doesn't have a fallback way to generate an unique MAC address, so we rely on CONFIG_NET_RANDOM_ETHADDR to have a valid one. An exception is the Radxa Zero board who doesn't have Ethernet on board so depends on an (or multiple) eventual USB adapters, so leaving the CONFIG_NET_RANDOM_ETHADDR configs seems safer. Suggested-by: Tom Rini <trini@konsulko.com> Reviewed-by: Vyacheslav Bocharov <adeep@lexina.in> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20211122110710.1038893-1-narmstrong@baylibre.com
2022-01-05Merge https://source.denx.de/u-boot/custodians/u-boot-marvellTom Rini
- kwbimage: Fix checksum calculation for v1 images (Pierre)
2022-01-05tools: kwbimage: Fix checksum calculation for v1 imagesPierre Bourdon
Recent changes caused fields in the image main header to be modified after the header checksum had already been computed. Move the checksum computation to once again be the last operation performed on the header. Fixes: 2b0980c24027 ("tools: kwbimage: Fill the real header size into the main header") Signed-off-by: Pierre Bourdon <delroth@gmail.com> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2022-01-04configs: iot2050: Drop unused CONFIG_OF_LIST from defconfigJan Kiszka
DTBs are explicitly listed in the image source file for this board, and this list already became outdated. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
2022-01-04arm: apple: Remove CONFIG_SYS_SDRAM_BASEMark Kettenis
The memory layout is taken from the device tree passed to us by m1n1, so there is no need to define this. Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2022-01-04vexpress64: Enable VIRTIO_NET network driverPeter Hoyes
The SMSC driver is using the old driver model. Init the virtio system in vexpress64.c so that the network device is discovered. Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2022-01-04vexpress64: Enable OF_CONTROL and OF_BOARD for VExpress64Peter Hoyes
Capture x0 in lowlevel_init.S as potential fdt address. Modify board_fdt_blob_setup to use fdt address from either vexpress_aemv8.h or lowlevel_init.S. Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2022-01-04vexpress64: Clean up BASE_FVP boot configurationPeter Hoyes
Move env var address values to #defines so they can be reused elsewhere. Rename env var names to those recommended in the README and modify addresses to allow more space for the kernel. Fix issue where fdt is called with invalid arguments when booting without a ramdisk. Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2022-01-04vexpress64: Refactor header file to make it easier to add new FVPsPeter Hoyes
Rename from vexpress_aemv8a.h -> vepxress_aemv8.h as new FVPs may not be v8-A. No change in behavior. This is towards future work to enable support for the FVP_BaseR. Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2022-01-04doc: Add documentation for the Arm VExpress64 board configsPeter Hoyes
Create a new documentation section for Arm Ltd boards with a sub-page for the VExpress64 boards (FVP-A and Juno). Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-10 19:53:54 +0000