aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-10-13imx: tpc70: dts: Add TPC70 board (imx6q based) device tree descriptionLukasz Majewski
This commit defines the TPC70 imx6q board with device tree description. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13imx: tpc70: led: Enable LED default stateLukasz Majewski
This change sets the default state of LEDs on TPC70. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13imx: tpc70: cosmetic: Replace magic numbers when setting ENET clockLukasz Majewski
This is a cosmetic change, just to use proper define instead of magic numbers. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13imx: tpc70: Add board_boot_order() to distinguish between eMMC and SD bootLukasz Majewski
The TPC70 can boot from SD card (debug/development) and eMMC (production). The board_boot_order() function provides a run time check for the device from which one wants to boot (it is selected by GPIO pins setup). Moreover, a fallback to SD card is provided if the detection is not possible or working properly. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13imx: tpc70: config: Update TPC70 config to support eMMC's boot0 SPL updateLukasz Majewski
The TPC70 can boot from eMMC's boot0. This patch allows it to update this HW partition's SPL. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13imx: tpc70: config: Add script commands to update u-boot and OE's wicLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13pico-imx7d: Support distro boot for FIT image caseJun Nie
Support distro boot for pico imx7d in FIT image case. Signed-off-by: Jun Nie <jun.nie@linaro.org> Tested-by: Joris Offouga <offougajoris@gmail.com>
2019-10-13pico-imx7d: add config to enable CAAMJun Nie
Add config to enable CAAM so that hardware random number generator works. Signed-off-by: Jun Nie <jun.nie@linaro.org>
2019-10-13ARM: imx6q_logic: Remove legacy pinmuxing code from board file.Adam Ford
With the OCRAM expanded to 256KB and the SPL_PINCTRL enabled with -u-boot.dtsi entries to include the pinmuxing in SPL, the manual code setting up the pinmux can go away. This patch removes the legacy pinmuxing code from the board file. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-13ARM: imx6q_logic: Enable Pin muxing in SPLAdam Ford
With the 256KB of OCRAM available to SPL now, there should be enough room to enable the pinmuxing in SPL from the device tree. This patch enables SPL_PINCTRL et al and adds the serial and usdhc pin mux references to the -u-boot.dtsi file so the pins can be configured from the device tree. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-13ARM: imx6q_logic: Enable 256KB OCRAMAdam Ford
Since this board config only supports, the i.MX6D/i.MX6Q configurations, 256K of on-chip RAM is available which increases the space available to SPL to help further reduce board code and further enable device tree functions. This patch enables 256K of RAM. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-13board: tbs2910: Convert eth to driver modelSoeren Moch
So we can remove lots of legacy config code. Signed-off-by: Soeren Moch <smoch@web.de>
2019-10-13board: tbs2910: Convert pci to driver modelSoeren Moch
So we can get rid of legacy pci config code. PCI_PNP is not required for this board, remove it to reduce the size of the u-boot binary. DM_PCI does not start the host controller automatically anymore. Do so in preboot instead. Signed-off-by: Soeren Moch <smoch@web.de>
2019-10-13ARM: dts: imx6q-tbs2910: Sync devicetree with kernel 5.3Soeren Moch
Signed-off-by: Soeren Moch <smoch@web.de>
2019-10-13mx6: mx6sabre common: Use more conventional spelling of fdtfileSjoerd Simons
Both the distro boot configuration as well as the general pxe support standardized on fdtfile as the variable to hold the dtb filename. Adjust to follow that such that e.g. "pxe boot" will just work. Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
2019-10-13Add i.MX7D based Meerkat96 board supportShawn Guo
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of 96Boards community and complies with all Consumer Edition board specifications. https://www.novtech.com/products/meerkat96.html https://www.96boards.org/product/imx7-96/ The initial supported/tested devices include: - Debug serial - SD - USB Host (with Ethernet) With these support, it's good enough for loading Linux Kernel from SD or Ethernet over USB. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-10-13ARM: dts: import meerkat96 board supportShawn Guo
It imports device tree source of meerkat96 board from Linux Kernel. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2019-10-13travis: Exclude MIPS from the bcm jobTom Rini
We don't need to pull in anything from the MIPS job so exclude that from the new bcm job and make it clear it's building only ARM. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-12Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- Remember the device being emulated for Sandbox PCI - Update Kconfig options for FSP 1.0 - Drop RESET_BASE and RESET_SEG_SIZE that are no longer used
2019-10-12Merge branch '2019-10-11-master-imports'Tom Rini
- Assorted cleanups - FAT bugfixes - mediatek platform updates
2019-10-12Merge branch '2019-10-11-ti-imports'Tom Rini
- Various improvements to dra7xx, keystone 3, am65x SoCs - Platform updates - remoteproc improvements
2019-10-11cmd: itest: add support for .q size specifierMarek Szyprowski
Add support for quad (64bits) memory access specifier. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Lukasz Majewski <lukma@denx.de>
2019-10-11fs: fat: get_contents() always returns -1 for errorsHeinrich Schuchardt
If out of memory, return -1 and not -ENOMEM from get_contents(). Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-10-11fs: fat: treat invalid FAT clusters as errorsHeinrich Schuchardt
When hitting an invalid FAT cluster while reading a file always print an error message and return an error code. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-10-11sandbox: Remove sandbox_noblk buildTom Rini
At this point, all drivers that do not use CONFIG_BLK are past their migration deadlines, so remove this config as it's no longer helpful and hinders enhancing block drivers. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-11spl: Introduce SPL_DM_SPI Kconfig defineLukasz Majewski
This define indicates if DM_SPI shall be supported in SPL. This allows proper operation of DM converted SPI drivers in SPL, which use #if !CONFIG_IS_ENABLED(DM_SPI) to also support not yet DM/DTS converted boards. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-11arm64: print instructions leading to exceptionHeinrich Schuchardt
If an exception occurs in a loaded image and the relocation offset is unknown, it is helpful to know the instructions pointed to by the program counter. This patch adds the missing output. A possible output is: Code: 910c4021 aa1303e0 f9400662 d63f0040 (e7f7defb) The parentheses indicate the instruction causing the exception. The output can be disassembled using scripts/decodecode: echo 'Code: 90000360 9100b800 94002782 17ffff8f (e7f7defb)' | \ ARCH=arm64 scripts/decodecode Code: 90000360 9100b800 94002782 17ffff8f (e7f7defb) All code ======== 0: 90000360 adrp x0, 0x6c000 4: 9100b800 add x0, x0, #0x2e 8: 94002782 bl 0x9e10 c: 17ffff8f b 0xfffffffffffffe48 10:* e7f7defb .inst 0xe7f7defb ; undefined <-- trapping instruction Code starting with the faulting instruction =========================================== 0: e7f7defb .inst 0xe7f7defb ; undefined We already have implemented the same for armv7. For testing command 'exception undefined' can be used. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-10-11cmd: avoid decimal conversionT Karthik Reddy
This patch uses auto instead of decimal in simple_strtoul(). Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-11ARM: asm/io.h: remove redundant #if !defined(readb) blockRasmus Villemoes
readb is unconditionally defined earlier in io.h, so there's no point checking whether it's undefined. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2019-10-11ARM: asm/io.h: kill off confusing #ifdef __mem_pci blockRasmus Villemoes
No ARM board seems to define __mem_pci - and if it did, one would get tons of ./arch/arm/include/asm/io.h:307:0: warning: "readl" redefined warnings, because readl and friends are unconditionally defined earlier in io.h. Moreover, the redefinitions lack the memory barriers that the first definitions have. So I'm guessing this is practically dead code. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2019-10-11spl: mmc: Add option to set eMMC HW boot partitionMans Rullgard
This change allows setting pre-defined eMMC boot partition for SPL eMMC booting. It is necessary in the case when one wants to boot (through falcon boot) from eMMC after loading SPL from other memory (like SPI-NOR). Signed-off-by: Mans Rullgard <mans@mansr.com> [lukma: Edit the commit message] Signed-off-by: Lukasz Majewski <lukma@denx.de> Acked-by: Andreas Dannenberg <dannenberg@ti.com>
2019-10-11spl: mmc: Fix indentation in spl_mmc.c fileMans Rullgard
This fixes a wrongly indented block of code. Signed-off-by: Mans Rullgard <mans@mansr.com> [lukma: Make the commit message more verbose] Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-11arm: dra7xx: Hang on any failure during IOdelay recalibrationLokesh Vutla
If there is any failure during IOdelay recalibration sequence, IOs are not guaranteed to behave as expected. So hang on any failure during the sequence. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11arm: dra7xx: Fix error path in iodelay recalibrationLokesh Vutla
When an error is reported in __recalibrate_iodelay_start(), de-isolation of IO doesn't happen. Because of this, undefined behaviour is observed on many peripherals without any error. So make sure io is out of isolation at the end of iodelay recalibration. Reported-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11tao3530: Fix usage of mmc rescanJarkko Nikula
Currently "bootcmd" does not work as intended but instead prints MMC usage information and goes directly to "nandboot". Follow what the commit 669681104daa ("configs: Fix usage of mmc rescan") does for other boards prior to support for TechNexion TAO3530 SoM was added. Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
2019-10-11configs: am43xx_evm: Enable USB supportLokesh Vutla
spl_dm_init is failing as usb to be probed with the following error: "omap_dwc3@483c0000: ret=-2" Enable usb to make spl boot on am43xx devices Reported-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11arm: dts: k3-j721e-common-proc-board: Mark main_uart0 as shared deviceLokesh Vutla
Main uart0 is used as debug console by both R5SPL and A72 bootloader and Linux. So mark it as shared device so that power-domain request is successful by both cores. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11board: ti: am335x-ice: Configure the CDCE913 clock synthesizerTero Kristo
AM335x-ICE boards contain the CDCE913 clock synthesizer, and their reset crystal capacitance load value of 10pF is wrong leading into lost packets in certain networking tests. Add DT data for this device, and probe it from the board file to program the crystal capacitance load value to 0pF to avoid any problems. Signed-off-by: Tero Kristo <t-kristo@ti.com>
2019-10-11board: ti: am43xx-idk: Configure the CDCE913 clock synthesizerTero Kristo
AM43xx-IDK boards contain the CDCE913 clock synthesizer, and their reset crystal capacitance load value of 10pF is wrong leading into lost packets in certain networking tests. Add DT data for this device, and probe it from the board file to program the crystal capacitance load value to 0pF to avoid any problems. Signed-off-by: Tero Kristo <t-kristo@ti.com>
2019-10-11board: ti: am57xx-idk: Configure the CDCE913 clock synthesizerTero Kristo
AM57xx-IDK boards contain the CDCE913 clock synthesizer, and their reset crystal capacitance load value of 10pF is wrong leading into lost packets in certain networking tests. Add DT data for this device, and probe it from the board file to program the crystal capacitance load value to 0pF to avoid any problems. Signed-off-by: Tero Kristo <t-kristo@ti.com>
2019-10-11clk: cdce9xx: add support for cdce9xx clock synthesizerTero Kristo
Add support for CDCE913/925/937/949 family of devices. These are modular PLL-based low cost, high performance, programmable clock synthesizers, multipliers and dividers. They generate up to 9 output clocks from a single input frequency. The initial version of the driver does not support programming of the PLLs, and thus they run in the bypass mode only. The code is loosely based on the linux kernel cdce9xx driver. Signed-off-by: Tero Kristo <t-kristo@ti.com>
2019-10-11arm: k3: Use driver_name to get ti_sci handleLokesh Vutla
Use the driver name to get ti_sci handle rather than relying on just the FIRMWARE uclass. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11configs: am65x_evm_a53: Enable DISPLAY_CPUINFOLokesh Vutla
Enable CONFIG_DISPLAY_CPUINFO so that cpuinfo is printed during boot. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11configs: j721e_evm_a72: Enable DISPLAY_CPUINFOLokesh Vutla
Enable CONFIG_DISPLAY_CPUINFO so that cpuinfo is printed during boot. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11board: am65x: Print board name and version during bootLokesh Vutla
Print the board name and ver along with the DT Model. While at it print the ver for all the detected daughter cards. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11arm: k3: Add support for printing CPUINFOLokesh Vutla
Add support for printing CPU info for all K3 devices. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11configs: j721e_evm_a72: Disable PSCI_RESETLokesh Vutla
J721E uses TISCI protocol to reset the device and does not support PSCI reset. So disable PSCI reset. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11configs: am65x_evm_a53: Disable PSCI_RESETLokesh Vutla
AM65x uses TISCI protocol to reset the device and does not support PSCI reset. So disable PSCI reset. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11mmc: am654_sdhci: Drop a redundant power_domain_on in probeLokesh Vutla
Power-domain is enabled by default in device_probe. am654 mmc driver is enabling power-domain again in probe. As the second call is redundant, drop power_domain_on from probe. Tested-by: Suman Anna <s-anna@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-11configs: ti: Use addr_fit for run_fit environment variableAndrew F. Davis
When running 'run_fit' the FIT file should have been loaded at 'addr_fit', although at this point they should be the same use this variable instead of 'loadaddr'. Signed-off-by: Andrew F. Davis <afd@ti.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-16 01:02:31 +0000