aboutsummaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2023-02-13clocks: qcs404: Add support for I2C clocksSumit Garg
Co-developed-by: Mike Worsfold <mworsfold@impinj.com> Signed-off-by: Mike Worsfold <mworsfold@impinj.com> Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
2023-02-13Merge tag 'i2c-updates-for-v2023.04' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-i2c i2c updates for v2023.04 - add new i2c driver ast2600 from Ryan Chen - i2c-cdns: make read fifo-depth configurable through device tree from Pei Yue Ho - mxc i2c driver: print base address in hex, not in decimal from Fabio
2023-02-13arm: kirkwood: Enable uart0 dm-pre-reloc for Pogoplug V4 boardTony Dinh
When DM_SERIAL is enabled, the device-tree tag u-boot,dm-pre-reloc is required for this board to boot over UART with kwboot. Enable this in kirkwood-pogoplug-series-4-u-boot.dtsi. Added by Stefan while applying: Please note that it's not fully understood, why this property really is needed. Here a link to the discussion about this: https://lore.kernel.org/r/20230201080210.ypz4nrj4y2igwxz3@pali/ Signed-off-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
2023-02-13arm: mvebu: Add support for Synology DS116 (Armada 385)Tony Dinh
Synology DS116 is a NAS based on Marvell Armada 385 SoC. Board Specification: - Marvel MV88F6820 Dual Core at 1.8GHz - 1 GiB DDR3 RAM - 8MB Macronix mx25l6405d SPI flash - I2C - 2x USB 3.0 - 1x GBE LAN port (PHY: Marvell 88E1510) - 1x SATA (6 Gbps) - 3x LED - PIC16F1829 (connected to uart1) - GPIO fan - serial console Note that this patch depends on the add-support for Thecus N2350 patch: https://patchwork.ozlabs.org/project/uboot/patch/20230201231306.7010-1-mibodhi@gmail.com/ Signed-off-by: Tony Dinh <mibodhi@gmail.com>
2023-02-13arm: mvebu: Add support for Thecus N2350 (Armada 385) boardTony Dinh
Thecus N2350 is a NAS based on Marvell Armada 385 SoC. Specification: - Processor: Marvel MV88F6820 Dual Core at 1GHz - 1 GiB DDR4 RAM - 4MB Macronix mx25l3205d SPI flash - 512MB Hynix H27U4G8F2DTR-BC NAND flash - I2C - 2x USB 3.0 - 1x GBE LAN port (PHY: Marvell 88E1510) - 2x SATA (hot swap slots) - 3x buttons - 10x LEDS - serial console Signed-off-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
2023-02-13arm: kirkwood: Use CONFIG_SYS_NS16550 with DM_SERIAL for Kirkwood boardsTony Dinh
CONFIG_SYS_NS16550 is required when DM_SERIAL is enabled for Kirkwood boards. Signed-off-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Stefan Roese <sr@denx.de>
2023-02-13arm: aspeed: dtsi: add reg for i2cRyan Chen
The i2c driver have global register that i2c bus use ofnode_get_parent to get parent register address. Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2023-02-12socfpga: fix the serial console on DE1-SoCJade Lovelace
Previously, the TX LED would flash but nothing would appear on the serial port, and the board would appear dead with a build of the socfpga_cyclone5_defconfig. I have verified that adding the frequency to the uart will fix the serial console on my board. Thanks to @ehoffman on the Rocketboards forum: https://forum.rocketboards.org/t/cyclonev-programming-fpga-from-u-boot/2230/30 Signed-off-by: Jade Lovelace <lists@jade.fyi> Reviewed-by: Marek Vasut <marex@denx.de>
2023-02-12Merge branch 'for-2023.04' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-mpc8xx - A fix for a long standing bug that has been exposed by commit 50128aeb0f8 ("cyclic: get rid of cyclic_init()") preventing 8xx boards from booting since u-boot 2023.01 - A GPIO driver for powerpc 8xx chip - Fixup for powerpc 8xx SPI driver - A new powerpc 8xx board - The two devices having that board.
2023-02-11board: cssi: Add new board MCR3000_2GChristophe Leroy
This adds a new board from CS GROUP. The board is called MCR3000_2G, and has a CPU board called CMPC885. That CPU board is shared with another equipment that will be added in a later patch. That board stores Ethernet MAC addresses in an EEPROM which is accessed using SPI bus. This patch was originally written by Charles Frey who's email address is not valid anymore as he left the company. Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
2023-02-11driver, gpio: Add support for MPC 8xx CPU portsChristophe Leroy
Ports A, C and D are 16 bits ports. Ports B and E are 32 bits ports. The "compatible" is used to determine each port type. This patch was originally written by Charles Frey who's email address is not valid anymore as he left the company. Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
2023-02-10board: MCR3000: Use lowercase filenamesChristophe Leroy
Rename MCR3000.* to mcr3000.* to be more in line with other boards. Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
2023-02-10powerpc/mpc8xx: Zero boot_flags arg for calling board_init_f()Christophe Leroy
Copied from e83a7e94532 ("powerpc/mpc83xx: Zero boot_flags arg for calling board_init_f()") The argument boot_flags of board_init_f() is not used at all in the powerpc specific board.c init sequence. Now with the generic init sequence, this boot_flags arg is used by board_init_f(). This patch sets the r3 register that is used to pass the boot_flags argument from the start.S board_init_f() call to 0 prior to the function call to avoid unknown content to end up in gd->flags. Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Fixes: 09f3ca3dd53 ("arm, powerpc: select SYS_GENERIC_BOARD")
2023-02-10dm: button: add support for linux_code in button-gpio.c driverDzmitry Sankouski
Linux event code must be used in input devices, using buttons. Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2023-02-10test: create dedicated fdt node for ofnode_for_each_prop testDzmitry Sankouski
Property count may change in /buttons node, if more button tests added, and this will break ofnode_for_each_prop. Add separate node for mentioned test. Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2023-02-10dts: add missing linux,code in gpio-keysDzmitry Sankouski
gpio-keys linux driver enforces user to specify linux,code. Add missing linux,code before implementing button input support. - arch/arm/dts/rk3288-popmetal.dtsi -> KEY_POWER - arch/arm/dts/rk3288-tinker.dtsi -> KEY_POWER - arch/arm/dts/am3517-evm-ui.dtsi -> KEY_RECORD - sandbox/dts/sandbox.dtsi -> BTN_1 - sandbox/dts/sandbox.dts -> BTN_1 Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2023-02-10dts: qcs404-evb: Add I2C controller nodesSumit Garg
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
2023-02-10pinctrl: qcs404: Enable I2C pinmux optionsSumit Garg
Co-developed-by: Mike Worsfold <mworsfold@impinj.com> Signed-off-by: Mike Worsfold <mworsfold@impinj.com> Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
2023-02-10clock-snapdragon: Add clk_rcg_set_rate() with mnd_width=0Sumit Garg
Add clk_rcg_set_rate() which allows to configure clocks without programming MND values. This is required for configuring I2C clocks on QCS404. Co-developed-by: Mike Worsfold <mworsfold@impinj.com> Signed-off-by: Mike Worsfold <mworsfold@impinj.com> Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
2023-02-10dts: qcs404-evb: Add ethernet controller nodeSumit Garg
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
2023-02-10pinctrl-snapdragon: Get rid of custom drive-strength valuesSumit Garg
Use standard pinconf drive-strength values from Linux DT bindings rather than ones based on custom u-boot header. These changes are in direction to make u-boot DTs for Qcom SoCs to be compatible with standard Linux DT bindings. Also, add support for pinconf bias-pull-up. Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
2023-02-10pinctrl: qcs404: Enable ethernet pinmux optionsSumit Garg
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
2023-02-10clocks: qcs404: Add support for ethernet clocksSumit Garg
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
2023-02-10qcs404-evb: Enable msm_gpio driver supportSumit Garg
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
2023-02-10qcs404: sysmap: Don't map reserved memory rangesSumit Garg
Currently u-boot maps whole of 1G RAM but there reserved memory ranges on QCS404 which are reserved for TrustZone, various firmware components etc. Any access to these reserved memory ranges causes a bus hang issue. So disable mapping for reserved memory ranges in u-boot. Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
2023-02-10Correct SPL uses of ROCKCHIP_OTPSimon Glass
This converts 2 usages of this option to the non-SPL form, since there is no SPL_ROCKCHIP_OTP defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-10Correct SPL uses of FASTBOOTSimon Glass
This converts 3 usages of this option to the non-SPL form, since there is no SPL_FASTBOOT defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-10Correct SPL uses of USB_KEYBOARDSimon Glass
This converts 2 usages of this option to the non-SPL form, since there is no SPL_USB_KEYBOARD defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-10Correct SPL use of SYS_FSL_ERRATUM_A010539Simon Glass
This converts 1 usage of this option to the non-SPL form, since there is no SPL_SYS_FSL_ERRATUM_A010539 defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-10Correct SPL use of STM32MP15X_STM32IMAGESimon Glass
This converts 1 usage of this option to the non-SPL form, since there is no SPL_STM32MP15X_STM32IMAGE defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-10Correct SPL uses of SAVE_PREV_BL_INITRAMFS_START_ADDRSimon Glass
This converts 2 usages of this option to the non-SPL form, since there is no SPL_SAVE_PREV_BL_INITRAMFS_START_ADDR defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-10Correct SPL uses of SAVE_PREV_BL_FDT_ADDRSimon Glass
This converts 2 usages of this option to the non-SPL form, since there is no SPL_SAVE_PREV_BL_FDT_ADDR defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-10Correct SPL uses of ROCKCHIP_EFUSESimon Glass
This converts 2 usages of this option to the non-SPL form, since there is no SPL_ROCKCHIP_EFUSE defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-10Correct SPL uses of PMIC_STPMIC1Simon Glass
This converts 2 usages of this option to the non-SPL form, since there is no SPL_PMIC_STPMIC1 defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-10Correct SPL use of OCTEON_SERIAL_PCIE_CONSOLESimon Glass
This converts 1 usage of this option to the non-SPL form, since there is no SPL_OCTEON_SERIAL_PCIE_CONSOLE defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-10Correct SPL use of OCTEON_SERIAL_BOOTCMDSimon Glass
This converts 1 usage of this option to the non-SPL form, since there is no SPL_OCTEON_SERIAL_BOOTCMD defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-10Correct SPL uses of MTDSimon Glass
This converts 2 usages of this option to the non-SPL form, since there is no SPL_MTD defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-10Correct SPL use of MIPS_CMSimon Glass
This converts 1 usage of this option to the non-SPL form, since there is no SPL_MIPS_CM defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-10Correct SPL uses of LMBSimon Glass
This converts 9 usages of this option to the non-SPL form, since there is no SPL_LMB defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-10Correct SPL uses of IMX_MODULE_FUSESimon Glass
This converts 6 usages of this option to the non-SPL form, since there is no SPL_IMX_MODULE_FUSE defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-09Correct SPL use of EXYNOS7420Simon Glass
This converts 1 usage of this option to the non-SPL form, since there is no SPL_EXYNOS7420 defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-09Correct SPL use of DISPLAY_CPUINFOSimon Glass
This converts 1 usage of this option to the non-SPL form, since there is no SPL_DISPLAY_CPUINFO defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-09Correct SPL uses of CPU_MICROBLAZESimon Glass
This converts 2 usages of this option to the non-SPL form, since there is no SPL_CPU_MICROBLAZE defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-09Correct SPL use of CMD_NETSimon Glass
This converts 1 usage of this option to the non-SPL form, since there is no SPL_CMD_NET defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-09Correct SPL use of CMD_BOOTZSimon Glass
This converts 1 usage of this option to the non-SPL form, since there is no SPL_CMD_BOOTZ defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-09Correct SPL uses of BOOTSTAGE_REPORTSimon Glass
This converts 2 usages of this option to the non-SPL form, since there is no SPL_BOOTSTAGE_REPORT defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-09Correct SPL use of BOOTSTAGE_FDTSimon Glass
This converts 1 usage of this option to the non-SPL form, since there is no SPL_BOOTSTAGE_FDT defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-09Correct SPL uses of ARMADA_8KSimon Glass
This converts 2 usages of this option to the non-SPL form, since there is no SPL_ARMADA_8K defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-09Correct SPL uses of ARMADA_3700Simon Glass
This converts 2 usages of this option to the non-SPL form, since there is no SPL_ARMADA_3700 defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-09Correct SPL uses of ALLEYCAT_5Simon Glass
This converts 2 usages of this option to the non-SPL form, since there is no SPL_ALLEYCAT_5 defined in Kconfig Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-16 02:36:34 +0000