| Age | Commit message (Collapse) | Author |
|---|
|
The MMC SPL locates the BSS section to a different memory region
from text, then use "_image_binary_end" variable to point to the
correct device tree location.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
Because the MMC SPL puts the bbs section in the ddr memory, move
calling mem_init() before calling spl_init().
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
Before setting up the serial communications, bring in the serial
device from the device tree file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
When OF_CONTROL is enabled, MMC boot device should not be detected
automatically, it should be MMC1 fixedly only the status "enabled"
is available.
Add NAND Flash boot device as well.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
Add the device tree file for sama5d4ek board.
The dts file is copied from Linux-4.4, do the following changes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compilation warning.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
Add the device tree files for sama5d4 Xplained board.
The dts files are copied from Linux-4.4, do the following changes.
- add reg property for pinctrl node.
- move the gpio nodes(pioA, pioB, pioC ...) from the pinctrl child's
nodes to its slibling nodes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
Add the device tree file for sama5d3 Xplained board.
The dts files are copied from the Linux-4.9, do changes as below.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compile warning.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
Add the device tree files for sama5d3xek board.
The dts files are copied from Linux-4.9, do the changes as below.
- add reg property for the pinctrl node.
- move the gpio nodes (pioA, pioB, pioC ...) as the pinctrl's
slibling nodes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compile warning.
- add spi0 node aliases.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
AT91 PIO controller is a combined gpio-controller, pin-mux and
pin-config module. The peripheral's pins are assigned through
per-pin based muxing logic.
Each SoC will have to describe the its limitation and pin
configuration via device tree. This will allow to do not need
to touch the C code when adding new SoC if the IP version is
supported.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The intention of the removal is the preparation to introduce the
new AT91 PIO pinctrl driver.
Use the union to make the PIO3 and PIO2's registers be together
and make their offset aligned.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
When the CONFIG_ATMEL_LEGACY is undefined, according to the following
defines, at91_set_gpio_value() references to at91_set_pio_value(x, y)
with two parameters.
#define at91_set_gpio_value(x, y) at91_set_pio_value(x, y)
#define at91_get_gpio_value(x) at91_get_pio_value(x)
But there isn't the implementation of at91_set_pio_value(x, y) with
two parameters in U-Boot. This is an error.
Same as at91_get_gpio_value(x) define.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
As reported in STAR 9001165532, an SLC control reg read (for checking
busy state) right after SLC invalidate command may incorrectly return
NOT busy causing software to NOT spin-wait while operation is underway.
(and for some reason this only happens if L1 cache is also disabled - as
required by IOC programming model)
Suggested workaround is to do an additional Control Reg read, which
ensures the 2nd read gets the right status.
Same fix made in Linux kernel:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=c70c473396cbdec1168a6eff60e13029c0916854
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
|
|
This simple PMU driver allows to tyrn power on and off for selected
devices. In particularly Intel Tangier needs to power on SDHCI
controllers in order to access to them during board initialization.
In the future it might be expanded to cover other Intel MID platforms,
that's why it's located under arch/x86/lib and called pmu.c.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Intel MID platforms have few microcontrollers inside SoC, one of them
is so called System Controller Unit (SCU).
Here is the driver to communicate with microcontroller.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Checking 'is_zimage' at this time will always fail and therefore booting
a FIT style image will always lead to this error message:
"## Kernel loading failed (missing x86 kernel setup) ..."
This change now removes this check and booting of FIT images works just
fine.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Since we now have the file names configurable via Kconfig for the flash
descriptor and intel-me files, add these from Kconfig in the corresponding
dts nodes.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This introduces two Kconfig options to enable board specific filenames
for the Intel binary blobs to be used to generate the SPI flash image.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Adds an additional image type needed for supporting secure keystone
devices. The build generates u-boot_HS_MLO which can be used to boot
from all media on secure keystone devices.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
As K2 can directly boot U-Boot, add u-boot_HS_MLO as the secure image
name for secure K2 devices, for all boot modes other than SPI flash.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Like the OMAP54xx, AM43xx, & AM33xx family SoCs, the keystone family
of SoCs also have high security enabled models. Allow K2E devices to
be built with HS Device Type Support.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
This commit implements the board_fit_image_post_process() function for
the keystone architecture. This function calls into the secure boot
monitor for secure authentication/decryption of the image. All needed
work is handled by the boot monitor and, depending on the keystone
platform, the security functions may be offloaded to other secure
processing elements in the SoC.
The boot monitor acts as the gateway to these secure functions and the
boot monitor for secure devices is available as part of the SECDEV
package for KS2. For more details refer doc/README.ti-secure
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Up till this commit passing NULL as input parameter was allowed, but not
handled properly.
When one passed NULL to one of this function parameters, the code was
executed causing data abort.
However, what is more interesting, the abort was not caught because of code
execution in HYP mode with masked CPSR A bit ("Imprecise Data Abort mask bit).
The TI's AM57xx SoC switch to HYP mode with A bit masked in lowlevel_init.S
due to SMC call. Such operation (by default) is performed in SoC ROM code.
The problem would pop up when one:
- Switch back to SVC mode after disabling LPAE support
- Somebody enables A bit (by executing cpsie a asm instruction)
and then the previously described exception would be caught.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
|
|
|
|
spl_mmc.c calls mmc_initialize(). This symbol is provided in
drivers/mmc/mmc.c when CONFIG_GENERIC_MMC is enabled.
The sunxi Kconfig case is an oddball because it redefines
SPL_MMC_SUPPORT.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
[trini: Update arch/arm/cpu/armv8/zynqmp/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
It also enables commands for cache enable/disable/status.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
This patch adds armv7m instruction & data cache support.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
Recent Linux distributions (e.g. Debian 9) include cross-compilers for
AArch64, but only for the aarch64-linux-gnu triplet only. It can thus
be expected that users will attempt to use the system cross-compiler
(instead of an aarch64-elf variant) to compile U-Boot for their ARMv8
target systems.
One key differences between an aarch64-linux-gnu and an aarch64-elf
compiler are the default settings regarding position-independent: with
the aarch64-linux-gnu compiler, the default will create and use the
global offset table.
This change-set adjusts the list of sections copied on ARMv8 to include
the GOT sections. With this added, the list matches the previous setup
for AArch32 closely.
Note that this is not an 'academic' issue, but was in fact encountered
by our QA during testing of the RK3399-Q7 BSP and resulted in an
early failure of the SPL stage during FDT setup.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The Sunchip CX-A99 is a board used in some media players. It features:
An Allwinner A80 ARM SoC (4 * Cortex-A7 + 4 * Cortex-A15 cores)
2 GiB or 4 GiB DDR3 DRAM
AXP808 PMIC
16 GB or 32 GB eMMC
SDIO Wifi/Bluetooth/FM module
SD card slot
1 USB 3.0 connector
2 USB 2.0 connectors
SATA connector
UART connector (internally) for serial console
Ethernet connector (10/100/1000 Mbit/s)
HDMI connector
Composite video and analog audio connector
S/PDIF connector
IR remote control receiver
This patch adds a defconfig for the board. The DRAM settings are as found
in the vendor sys_config.fex file.
It has a preliminary device tree for use until a device tree is accepted
upstream, after which it can be replaced by the upstream version.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
[squash commits, and edited new meanful commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
commit 56b0730157f70dc23d6caff9e7ceb8b377b96b9f upstream.
On the A80, mmc1 is available on pingroup G. Designs mostly use this
to connect to an SDIO WiFi chip.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Those DT will be part of 4.10, sync them so we can have our own config.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jagan Teki <jagan@openedev.com>
|
|
Add support for the NanoPi NEO Air H3 board from friendlyarm.com . This
board contains WiFi, Bluetooth, 8GB eMMC storage and 512 MB DDR3 ram.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Rebase on master]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Add the i2c-gpio nodes for fuelgauge and max77693.
There are i2c8 and i2c9.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
With d53ecad92f06 some unused interrupt related code was removed.
However all of these options are currently unused. Rather than migrate
some of these options to Kconfig we just remove the code in question.
The only related code changes here are that in some cases we use
CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename
and move the value local to the code in question.
Fixes: d53ecad92f06 ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi")
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
trini: Disable CONFIG_SPL_USE_ARCH_MEMSET on orangepi_2
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This header file is used by three archs. It could be used by all of them
since relocation is a common function. Move it into a generic file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This header file is used by two archs. It could be used by all of them
since it allows the cache to be on during relocation. Move it into a
generic file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We don't need this PPC-specific function in generic code. Move it to
the powerpc directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
This is an weak function present on all archs so we should have it in the
common header file. Remove it from arch-specific headers and add a
function comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
At present we misuse print_cpuinfo() do so CPU init on x86. This is done
because it is the next available call after the console is enabled. But
several arches use checkcpu() instead. Despite the horrible name (which
we can fix), it seems a better choice.
Adjust the various x86 CPU implementations to move their init code into
checkcpu() and use print_cpuinfo() only for printing CPU info.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Move these two function calls into checkcpu(), which is called on this
arch immediately after these two.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
We don't need a special hook for sandbox as one of the later ones will do
just as well. We can print error messages about bad options after we
print the banner. In fact, it seems better.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
This function is called just before checkcpu() on MPX83xx. Move it to the
code for that arch.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
There is no good reason to use a different name on PowerPC. Change it to
timer_init() like the others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
