aboutsummaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2017-11-20i2c: add Amlogic Meson driverBeniamino Galvani
Add a driver for the I2C controller available on Amlogic Meson SoCs. Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
2017-11-17Add UART base addresses for additional UARTsLandheer-Cieslak, Ronald
UARTs 1 through 5 were missing in the code - added. Also pick the default according to the configuration setting for the console index. Signed-off-by: Ronald Landheer-Cieslak <ronaldlandheercieslak@eaton.com>
2017-11-17nios2: 10m50: Add CPU pre-relocation in device treeGan, Yau Wai
Tag CPU with dm-pre-reloc to enable driver before relocation. Signed-off-by: Gan, Yau Wai <yau.wai.gan@intel.com> Cc: Thomas Chou <thomas@wytron.com.tw> Reviewed-by: Marek Vasut <marex@denx.de>
2017-11-17configs: dragonboard410c: Save environment data on eMMCJorge Ramirez-Ortiz
Save the environment data at the end of the boot partition on emmc Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2017-11-17armv8: update gd after relocateKever Yang
We need to update gd in assamble code after relocate, this is a fix to: adc421e arm: move gd handling outside of C code Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-17arm64: support running at addr other than linked toStephen Warren
This is required in the case where U-Boot is typically loaded and run at a particular address, but for some reason the RAM at that location is not available, e.g. due to memory fragmentation loading other boot binaries or firmware, splitting an SMP complex between various different OSs without using e.g. the EL2 second-stage page tables to hide the memory asignments, or due to known ECC failures. Signed-off-by: Stephen Warren <swarren@nvidia.com>
2017-11-17arm: meson: Add supplementary ethernet registers definitionsNeil Armstrong
On Amlogic Meson GXL/GXM, supplementary ethernet configuration registers were added to configure the internal RMII PHY interface. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2017-11-17pylibfdt: compile pylibfdt only when dtoc/binman is necessaryMasahiro Yamada
Currently, pylibfdt is always compiled if swig is installed on your machine. It is really annoying because most of targets (excepts x86, sunxi, rockchip) do not use dtoc or binman. "checkbinman" and "checkdtoc" are wrong. It is odd that the final build stage checks if we have built necessary tools. If your platform depends on dtoc/binman, you must be able to build pylibfdt. If swig is not installed, it should fail immediately. I added PYLIBFDT, DTOC, BINMAN entries to Kconfig. They should be property select:ed by platforms that need them. Kbuild will descend into scripts/dtc/pylibfdt/ only when CONFIG_PYLIBFDT is enabled. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-17arm: add initial support for Amlogic P212 based on Meson GXL familyNeil Armstrong
This adds platform code for the Amlogic P212 reference board based on a Meson GXL (S905X) SoC with the Meson GXL configuration. This initial submission only supports UART and MMC/SDCard, support for the internal Ethernet PHY in Work In Progress. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
2017-11-17ARM: dts: Synchronize Amlogic from Linux Mainline 4.13.5Neil Armstrong
Synchronize the Amlogic ARM64 dts from mainline Linux 4.13.5 In the preparation of the support of the Amlogic P212 board, import the corresponding meson-gxl-s905x-p212.dts file. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
2017-11-17am33xx: Add a function to query MPU voltage in uVFelix Brack
For the DM TPS65910 driver I'm working on, querying the MPU voltage should return a value in uV. This value can then be used by the regulator's standard function set_value to set the MPU voltage. Signed-off-by: Felix Brack <fb@ltec.ch> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-11-16Merge git://www.denx.de/git/u-boot-marvellTom Rini
2017-11-16arm: mvebu: clearfog: update SPI flash DT descriptionBaruch Siach
All current ClearFog SOMs have the SPI flash populated. Enable SPI flash in the device tree. Add an alias to the SPI bus so that the 'sf' command can probe the flash on bus 1. Add the "spi-flash" compatible string to make the standard SPI flash driver probe the device. Reviewed-by: Jagan Teki <jagan@openedev.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Stefan Roese <sr@denx.de>
2017-11-16arm: mvebu: Add board_setup for xhci hardwareJon Nettleton
This fixes the USB 3.0 support for the a38x SOC. Signed-off-by: Jon Nettleton <jon@solid-run.com> [baruch: use fdt_addr_t] Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Stefan Roese <sr@denx.de>
2017-11-15driver: net: fsl-mc: Use base 16 in simple_strtoulPrabhakar Kushwaha
Value provided in MC_MEM_SIZE_ENV_VAR is in hex. Use 16 as base in simple_strtoul. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1088aqds: Add SD boot support for ls1088qdsAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1088ardb: Add SD boot support for ls1088Ashish Kumar
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1088: Enable SATA for ls1088Ashish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-12ARM: rmobile: Fix eMMC signal voltage on Salvator-X/XSMarek Vasut
The eMMC is 1V8 device only and the signaling is always 1V8, fix the DT for Salvator-X/XS to describe the hardware correctly. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-09Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2017-11-09imx7: Add include guards for include/asm/arch-mx7/sys_proto.h fileLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09imx5: Add include guards for include/asm/arch-mx5/sys_proto.h fileLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09imx6: Add include guards for include/asm/arch-mx6/sys_proto.h fileLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09imx:display5: Add support for LWN's DISPLAY5 boardLukasz Majewski
This commit provides support for LWN's IMX6Q based DISPLAY5 board. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09imx6: iomux: Add generic function to set RGMII IO voltage on IMX6 SoCsLukasz Majewski
This commit provides generic function to set the RGMII/HSIC IO voltage level on iMX6 devices. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-07mx51: Select the ESDHC_A001 erratumFabio Estevam
When a high speed card is connected to mx51evk the following error is seen: U-Boot 2017.11-rc2 (Oct 18 2017 - 13:49:26 -0200) CPU: Freescale i.MX51 rev3.0 at 800 MHz Reset cause: POR Board: MX51EVK DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 *** Warning - read failed, using default environment In: serial Out: serial Err: serial Net: FEC Hit any key to stop autoboot: 0 => saveenv Saving Environment to MMC... Writing to MMC(0)... failed The root cause for the failure is the eSDHC-A001 erratum: "eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 0x4,0x8, and 0xC" that is listed on some PowerArchitecture chips: https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf Even though eSDHC-A001 is not documented on the i.MX51 errata document, I have confirmed with the NXP design team that this erratum does affect i.MX51, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001 at SoC level. The i.MX51 ts4800 board already selects this option, but it is better to move this selection to the i.MX51 SoC level instead. Successfully tested with a high speed SD card on a mx51evk board. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
2017-11-07mx25: Select the ESDHC_A001 erratumFabio Estevam
When a high speed card is connected to mx25 the following error is seen: U-Boot 2017.11-rc2-00104-gb79372a (Oct 31 2017 - 11:02:22 -0200) CPU: Freescale i.MX25 rev1.2 at 399 MHz Reset cause: POR Board: MX25PDK I2C: ready DRAM: 64 MiB No arch specific invalidate_icache_all available! MMC: FSL_SDHC: 0 *** Warning - read failed, using default environment In: serial Out: serial Err: serial Net: FEC Hit any key to stop autoboot: 0 => saveenv Saving Environment to MMC... Writing to MMC(0)... failed , which prevents any usage of the SD card. The root cause for the failure is the eSDHC-A001 erratum: "eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 0x4,0x8, and 0xC" that is listed on some PowerArchitecture chips: https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf Even though eSDHC-A001 is not documented on the i.MX25 errata document, I have confirmed with the NXP design team that this erratum does affect i.MX25, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001 at SoC level. Successfully tested with a high speed SD card on a mx25pdk board. Suggested-by: Benoît Thébaudeau <benoit@wsystem.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br> Tested-by: Otavio Salvador <otavio@ossystems.com.br> # mx25pdk
2017-11-07mx25: Move MX25 selection to KconfigFabio Estevam
The motivation for moving MX25 selection to Kconfig is to be able to better handle MX25 specific errata, so that an errata option can be selected at SoC level instead of board level. This selection method also aligns with the way other i.MX SoCs are selected in U-Boot. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2017-11-07rockchip: dts: rk3399: change sd-card io voltage to 3.0VKlaus Goger
The VCC_SD and VCC_SDIO rail should only be powered up to 3.0V on RK3399 platforms. Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-07rockchip: dts: Use defines for pin names in rk3399-puma.dtsi and rk3368-lion.dtsKlaus Goger
pinctrl/rockchip.h provides defines that map pin numbers to pin names. Use them to make the dts more human readable. Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-07rockchip: dts: rk3399-puma: update USB configurationPhilipp Tomsich
This change updates the USB configuration for the RK3399-Q7 in the DTS: * fixes the OTG board configuration by enabling it ('okay') * improves the speed of 'usb start' by disabling the unused EHCI/OHCI controllers Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-11-07rockchip: dts: rk3399-puma: update usbhub_enable regulatorPhilipp Tomsich
To correctly model the usbhub_enable regulator for U-Boot, we need to change the settings to: * the GPIO polarity is GPIO_ACTIVE_LOW * should be set to inactive (enable-active-low) when boot-on settings are applied * it can be changed at runtime (i.e. remove the always-on) Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-11-07rockchip: dts: rk3399-puma: fix the modelling of BIOS_DISABLEPhilipp Tomsich
The fixed regulator for overriding BIOS_DISABLE had been modelling backwards (i.e. the GPIO polarity and the enable-active-low/high property had both been inverted), causing the 'regulator' command to always print/expect 'disabled'/'enabled' backwards. This fixes the mix-up and models it correctly: * the GPIO is low-active * the regulator should be enabled (enable-active-high) during boot-on initialisation Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-11-06cosmetic: rmobile: renesas spelled wrongChris Brandt
Renesas was spelled wrong. Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
2017-11-06spear: fix STMicroelectronics copyrightPatrice Chotard
Uniformize STMicroelectronics copyrights headers for SPEAR related code. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06stv0991: fix STMicroelectronics copyrightPatrice Chotard
Uniformize STMicroelectronics copyrights headers for STV0991 related code. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06stm32: fix STMicroelectronics copyrightPatrice Chotard
Uniformize STMicroelectronics copyrights headers for STM32 related code. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06sti: fix STMicroelectronics copyrightPatrice Chotard
Uniformize all STMicroelectronics copyrights headers for STi related code. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06ARM: dts: exynos: fix property values of LDO15/17 for ODROID-XU3/4Dongjin Kim
Looking at the schematic, LDO15 and LDO17 are tied as a power source of a builtin network chipset. The voltage on LDO15 is corrected to 3.3V and the name of LDO17 is corrected to "vdd_ldo17". Signed-off-by: Dongjin Kim <tobetter@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2017-11-01rockchip: rk3328: fix rockchip_get_cru apiKever Yang
The API for get priv pointer is wrong, fix it. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-31wandboard: Add support for the MX6QP variantFabio Estevam
Add support for the latest MX6QP wandboard variant. Based on Richard Hu's work from Technexion's U-Boot tree. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-10-29Merge git://git.denx.de/u-boot-videoTom Rini
2017-10-27Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2017-10-27armv8: sec_firmware: Add support for loadables in FITSumit Garg
Enable support for loadables in SEC firmware FIT image. Currently support is added for single loadable image. Brief description of implementation: Add two more address pointers (loadable_h, loadable_l) as arguments to sec_firmware_init() api. Create new api: sec_firmware_checks_copy_loadable() to check if loadables node is present in SEC firmware FIT image. If present, verify loadable image and copies it to secure DDR memory. Populate address pointers with secure DDR memory addresses where loadable is copied. Example use-case could be trusted OS (tee.bin) as loadables node in SEC firmware FIT image. Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27armv8: layerscape: Allocate 66 MB DDR for secure memorySumit Garg
Change DDR allocated for secure memory from 2 MB to 66 MB. This additional 64 MB secure memory is required for trusted OS running in Trusted Execution Environment using ARMv8 TrustZone. Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27armv8: ls1088ardb: Enable USB command RDB qspi-bootRan Wang
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com> Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27arm64: layerscape: Move CONFIG_HAS_FSL_XHCI_USB to KconfigRan Wang
Use Kconfig to select QE-HDLC and USB pin-mux. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27Merge git://git.denx.de/u-boot-x86Tom Rini
2017-10-27sunxi: video: add LCD support to DE2 driverVasily Khoruzhick
Extend DE2 driver with LCD support. Tested on Pinebook which is based on A64 and has ANX6345 eDP bridge with eDP panel connected to it. Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> [agust: rebased v5 on u-boot-video/master] Signed-off-by: Anatolij Gustschin <agust@denx.de>
2017-10-27sunxi: video: split out PLL configuration codeVasily Khoruzhick
It will be reused in new DM LCD driver. Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-10 20:50:04 +0000