| Age | Commit message (Collapse) | Author |
|---|
|
Instead of using EXTRA options in defconfig, use two targets
in Kconfig to select correct SoC.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
|
|
Juno uses a 1:1 mapping between CPU and PCI addresses for IO. First,
that will trip devices that cannot use more than 16 bits of addresses
for IO, second it is un-necessary as the system can handle zero-based
PCI addresses just fine.
Change the mapping to start IO bus addresses from zero.
Signed-off-by: Liviu Dudau <Liviu.Dudau@foss.arm.com>
|
|
Firmware provides a spin table on the raspberry pi. This table shouldn't
get overwritten by payloads, so we need to mark it as reserved.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
|
|
This patch removes use of U_BOOT_DEVICE in board/raspberrypi/rpi/rpi.c,
enables OF_CONTROL in the config and adjusts the rpi_*defconfig configs.
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
When using OF_CONTROL, the disabled value of the mini UART platdata
gets reset after board_early_init_f. So move detection and disabling
to board_init and remove board_early_init_f.
This uses the first device using the mini uart driver, as this method
works reliably with different device trees or even no device tree at all.
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The config option TARGET_K2x_EVM is set by the k2x defconfigs to pick
a board target, but the header configs also set K2x_EVM. This config
is redundant, remove it and use TARGET_K2x_EVM everywhere in its place.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
remove now unused CONFIG_TRDX_PID_XXX
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
With our common code in place actually make use of it across all our
modules.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Add Toradex factory configuration block handling. The config block is a
data structure which gets stored to flash during production testing. The
structure holds such information as board resp. hardware revision,
product ID and serial number which is used as the NIC part of the
Ethernet MAC address as well. The config block will be read upon boot by
the show_board_info() function, displayed as part of the board
information and passed to Linux via device tree or ATAGs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Add board support for sun8i_r16 Nintendo NES Classic edition.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
[jagan: Add commit message body]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
|
|
This adds support for the Asus Chromebook Flip, an RK3288-based clamshell
device which can flip into 'tablet' mode. The device tree file comes from
Linux v4.8. The SDRAM parameters are for 4GB Samsung LPDDR3.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This adds support for the Asus Chromebit, and RK3288-based device designed
to plug directly into an HDMI monitor. The device tree file comes from
Linux v4.8.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add a comment to indicate that we are not supporting the PWM regulator
yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present we have a single rk3288-based Chromebook: chromebook_jerry. But
all such Chromebooks can use the same binary with only device-tree
differences. The family name is 'veyron', so rename the files accordingly.
Also update the device-tree filename since this currently differs from
Linux.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The size dram node need to be deduced by the same amount of reserved space.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
arch/arm/Kconfig
|
|
Use TARGET_MPC8641HPCN from Kconfig instead.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use TARGET_MPC8610HPCD from Kconfig instead.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use CONFIG_TARGET_T4240RDB instead.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use TARGET_T4160RDB to simplify Kconfig options.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use CONFIG_TARGET_T4240QDS instead.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use TARGET_T4160QDS to simplify Kconfig options.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
T208XRDB only has one target T2080RDB. Use TARGET_T2080RDB in Kconfig
and clean up existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use two separated targets in Kconfig to simplify configurations.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
CONFIG_T104xRDB is defined in T104xRDB.h, so it is always enabled for
all T1040RDB, T1040D4RDB, T1042RDB, T1042D4RDB, T1042RDB_PI.
CONFIG_T104XD4RDB is defined for all T1040D4RDB, T1042D4RDB.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use TARGET_T1042RDB instead.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use TARGET_T1042D4RDB in Kconfig to simplify config options.
Remove macro CONFIG_T1042D4RDB.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use separated TARGET_T1042RDB_PI to simplify config options.
Remove macro CONFIG_T1042RDB_PI.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use CONFIG_TARGET_T1040RDB instead.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use TARGET_T1040D4RDB in Kconfig to simplify config macros. Replace
CONFIG_T1040D4RDB with TARGET_T1040D4RDB and clean up existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Replace CONFIG_PPC_T1040 with ARCH_T1040 in Kconfig and clean up
existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Split ARCH_T104XRDB as ARCH_T1040RDB and ARCH_T1042RDB in Kconfig to
simplify config options.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Replace CONFIG_PPC_T1024 with ARCH_T1024 in Kconfig and clean up
existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Rename TARGET_T102XQDS to TARGET_T1024QDS to match the name.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
The defconfig files are separated. Splitting targets in Kconfig simplifies
config options.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Replace CONFIG_PPC_B4420 with ARCH_B4420 in Kconfig and clean up
existing macros.
|
|
Use CONFIG_TARGET_B4860QDS instead.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use TARGET_B4420QDS to simplify Kconfig options.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use CONFIG_TARGET_P5040DS instead.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Replace CONFIG_P5040 with ARCH_P5040 in Kconfig and clean up
existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use CONFIG_TARGET_P5020DS instead.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use CONFIG_TARGET_P4080DS instead.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use CONFIG_TARGET_P3041DS instead.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use CONFIG_TARGET_P2041RDB instead.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Replace CONFIG_P2020 with ARCH_P2020 in Kconfig and clean up
existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
All boards covered by this group have been converted to their own
targers. Drop TARGET_P1_P2_RDB_PC from Kconfig.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use TARGET_P2020RDB_PC instead of sharing with P1_P2_RDB_PC to
simplify Kconfig and config macros.
Remove macro CONFIG_P2020RDB.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use TARGET_P1025RDB instead of sharing with P1_P2_RDB_PC to
simplify Kconfig and config macros.
Remove macro CONFIG_P1025RDB.
Signed-off-by: York Sun <york.sun@nxp.com>
|
