aboutsummaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2014-10-22dm: exynos: Make sure that GPIOs are requestedSimon Glass
With driver model GPIOs must be requested before use. Make sure this is done correctly. (Note that the soft SPI part of universal is omitted, since this driver is about to be replaced with a driver-model-aware version) Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22dm: exynos: Tidy up GPIO headersSimon Glass
The wrong header is being included, thus requiring the code to re-declare the generic GPIO interface in each GPIO header. Fix this. Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22arm: goni: add i2c_init_board()Robert Baldyga
Add proper initialization of GPIO pins used by software i2c. Signed-off-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-10-16ls102x: Add support for secure boot and enable blob commandRuchika Gupta
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-10-16ls102x: configs - Add hash command in freescale LS1 platformsRuchika Gupta
Hardware accelerated support for SHA-1 and SHA-256 has been added. Hash command enabled along with hardware accelerated support for SHA-1 and SHA-256 for platforms which have CAAM block. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-10-10Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2014-10-11Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-10-10sama5d3xek: run PHY's configAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Bo Shen <voice.shen@atmel.com>
2014-10-10ks2_evm: readme: align according to actual sourcesKhoronzhuk, Ivan
Update readme file for Keystone II EVM boards to actual sources. Also correct some typos. For now the Edison evaluation board is added, README for K2E is mostly the same, so update README to contain information also for K2E evm. Rename file to README as it contains information for all keystone evm boards. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-10board/BuR: fix pinmux for MII Ethernet InterfaceHannes Petermaier
The lines COL (collision detect) and CRS (carrier sense) needs to be connected and muxed to the CPSW MAC for a proper function in half-duplex Mode of the interface. Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at> Cc: Tom Rini <trini@ti.com>
2014-10-10PATI: fix broken SPI accessDavid Müller (ELSOFT AG)
fix broken SPI access by adding/activating BOARD_EARLY_INIT_F functionality and calling spi_init_f() from there. Signed-off-by: David Müller <d.mueller@elsoft.ch>
2014-10-10beagleboard: Remove side effects of i2c2 pullup resisters initialization codeAlexander Kochetkov
Fix typo of commit d4e53f063dd25e071444b87303573e7440deeb89. i2c2 pullup resisters are controlled by bit 0 of CONTROL_PROG_IO1. It's value after reset is 0x00100001. In order to clear bit 0, original code write 0xfffffffe to CONTROL_PROG_IO1 and toggle almost all default values. Original code affect following: * disable i2c1 pullup resisters * increase far end load setting for many modules * setup invalid SC/LB combination Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com> CC: Tom Rini <trini@ti.com> CC: Steve Kipisz <s-kipisz2@ti.com>
2014-10-10powerpc: mpc5xxx: remove board support for MVBC_P and MVSMRMasahiro Yamada
These boards have been orphaned for more than 6 months. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-10powerpc: mpc83xx: remove board support for MERGERBOX and MVBLM7Masahiro Yamada
These boards have been orphaned for more than 6 months. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-10powerpc: ppc4xx: remove board support for bluestoneMasahiro Yamada
This board has been orphaned for more than 6 months. It is the last board defining CONFIG_APM821XX. The code inside #ifdef CONFIG_APM821XX should be removed too. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-10powerpc: ppc4xx: remove board support for CRAYL1Masahiro Yamada
This board has been orphaned for more than 6 months. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-10powerpc: ppc4xx: remove board support for KAREF and METROBOXMasahiro Yamada
These boards have been orphaned for more than 6 months. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-10OMAP5+: sata/scsi: Implement scsi_init()Roger Quadros
On OMAP platforms, SATA controller provides the SCSI subsystem so implement scsi_init(). Get rid of the unnecessary sata_init() call from dra7xx-evm and omap5-uevm board files. Signed-off-by: Roger Quadros <rogerq@ti.com>
2014-10-10Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-10-09compulab: eeprom: add default eeprom busNikita Kiryanov
Add default eeprom bus setting. This addresses the trimslice compile error that was introduced with the addition of this setting. Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2014-10-09arm: rmobile: lager: Fix CPU frequency settingNobuhiro Iwamatsu
Setting to change the CPU frequency is only used version2. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-10-09arm: rmobile: lager: Add Qos setting for ES2Nobuhiro Iwamatsu
This adds support version 0.963 for ES2 of lager board. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-10-09arm: rmobile: lager: Update Qos setting to version 0.955Nobuhiro Iwamatsu
This updates QoS version 0.955 for ES1 of lager board. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-10-09arm: rmobile: alt: Update QoS initialization to version 0.11Nobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-10-09arm: rmobile: koelsch: Update QoS initialization to version 0.334Nobuhiro Iwamatsu
This update QoS version 0.334 for ES2 of R8A7791. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-10-08Merge remote-tracking branch 'u-boot-imx/master'Albert ARIBAUD
The single file conflict below is actually trivial. Conflicts: board/boundary/nitrogen6x/nitrogen6x.c
2014-10-08sunxi: Fix gmac not working reliable on the BananapiHans de Goede
In order for the gmac nic to work reliable on the Bananapi, we need to set bits 10-12 GTXDC "GMAC Transmit Clock Delay Chain" of the GMAC clk register (0x01c20164) to 3. Without this about 9 out of 10 ethernet packets get lost, with this setting there is no packet loss. So far setting these bits is only necessary on the Bananapi, so this commit solves this with a bit of #ifdef CONFIG_BANANAPI code. If in the future we need to do something similar for other boards, we can create a specific CONFIG_FOO option for this then. Reported-by: Karsten Merker <merker@debian.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Karsten Merker <merker@debian.org> Tested-by: Zoltan HERPAI <wigyori@openwrt.org> Tested-by: Tony Zhang <tony.zhang@lemaker.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-08odroid: clock: set aclk_cores to 200MHzPrzemyslaw Marczak
This change fixes suspend/resume issue in the kernel caused by the wrong 'aclk_cores' clock value expected by the kernel. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-10-08exynos: update maintainer of Snow and SMDK5420 boardMasahiro Yamada
The email address of Rajeshwari Shinde <rajeshwari.s@samsung.com> is not working. This commit gives Akshay the maintainership of Snow and SMDK5420 boards. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Akshay Saraswat <akshay.s@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-10-07Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2014-10-07vf610twr: Tune DDR initialization settingsAnthony Felice
Removed settings in unsupported register fields. They didn’t do anything, and in most cases, were not documented in the reference manual. Changed register settings to comply with JEDEC required values. Changed timing parameters because they included full clock periods that were doing nothing. Signed-off-by: Anthony Felice <tony.felice@timesys.com> [rebased on v2014.10-rc2] Signed-off-by: Stefan Agner <stefan@agner.ch>
2014-10-07Merge branch 'uboot'Minkyu Kang
2014-10-07Merge branch 'master' of http://git.denx.de/u-boot-samsungMinkyu Kang
2014-10-06nitrogen6x: display use I2C detect for HDMIEric Nelson
The HPD pin and RX_SENSE registers have proven to be less reliable than using I2C on the EDID pins for detection of an HDMI monitor. In particular, when the HDMI output is reset through a "reboot" cycle, the detect_hdmi() routine often bounces, resulting in a failure to detect a connected monitor. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06nitrogen6x: display: add wvga-lvds panelEric Nelson
Add support for WVGA (800x480) panels using VESA GTF timings over LVDS. No auto-detection is supported, so you must configure this panel manually through the 'panel' environment variable: U-Boot > setenv panel svga U-Boot > saveenv && reset Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06nitrogen6x: display: add Ampire 1024x600 panelEric Nelson
Add support for an Ampire 1024x600 LVDS panel with integrated Ilitek capacitive touch screen. Auto-detection is enabled, so no explicit configuration is needed. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06nitrogen6x: display: add svga display (800x600)Eric Nelson
Add support for 800x600 18-bit RGB displays using VESA GTF timings. No auto-detection is supported, so you must configure this panel manually through the 'panel' environment variable: U-Boot > setenv panel svga U-Boot > saveenv && reset Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06nitrogen6x: display: add support for fusion 7 displayEric Nelson
Add support for the Touch Revolution Fusion7 display: 800x480 RGB with a custom F0710A resistive touch controller. Auto-detection of this panel is supported so no configuration is required. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06nitrogen6x: display: add LDB-WXGA-S for SPWG 1280x800 displaysEric Nelson
This patch adds support for LVDS WXGA displays that use the SPWG encoding standard instead of JEIDA. No auto-detection is enabled and you must explicitly set the 'panel' environment variable: U-Boot > setenv panel LDB-WXGA-S U-Boot > saveenv && reset Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06nitrogen6x: display: add support for LG-9.7 LVDS displayEric Nelson
Add support for LG 9.7" LVDS panel (1024x768) with integrated eGalax touch screen. Note that this panel differs only slightly from the Hannstar XGA panel (margins). No auto-detection is available because it shares the same touch controller as the Hannstar-XGA display, so you'll need to configure it through the 'panel' environment variable: U-Boot > setenv panel LG-9.7 U-Boot > saveenv && reset Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06nitrogen6x: display: add qvga panelEric Nelson
Add support for a 1/4 VGA panel with a 24-bit RGB interface. No auto-detection is enabled, so you must configure the 'panel' environment variable to use this display: U-Boot > setenv panel qvga U-Boot > saveenv && reset Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06nitrogen6x: display: add support lvds jeida screenRobert Winkler
Add support for Boundary Devices 7" and 10.1" 1280x800 displays with integrated FocalTech ft5x06 10-point touch controller. Because they share the touch controller with the 1024x600 displays, auto-detection is disabled and you must explicitly set the 'panel' environment variable: U-Boot > setenv panel LDB-WXGA U-Boot > saveenv && reset Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com> Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06nitrogen6x: prevent warnings about board_ehci* callbacksEric Nelson
Include declarations of board_ehci callbacks to prevent compiler warnings and enforce function prototypes. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06nitrogen6x: phy: add 100 us delay after phy resetTroy Kisky
Testing shows that the Micrel PHY may not be completely out of reset if accessed immediately. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06nitrogen6x: staticize board fileEric Nelson
Declare locally-used data structures and functions as static and pull in header files to prevent compiler warnings of "Should it be static?" when building with "make C=1". Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06nitrogen6x: configure SGTL5000, CSI camera clock outputsTroy Kisky
Configure CLKO outputs for SGTL5000, CSI camera. The sys_mclk output for the SGTL500 in particular prevents Windows CE from properly driving audio. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06nitrogen6x: power-down miscellanous peripheralsEric Nelson
Ensure that cameras and USB OTG power are in a stable (reset) state at reset by configuring their pads and toggling GPIOs. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06nitrogen6x: configure SD2 pads for SDIO on USDHC2Eric Nelson
Pads SD2_CLK/CMD/DAT0-3 are connected to an SDIO WiFi device on Nitrogen and unconnected on BD-SL-i.MX6 (sabre lite). Configure them as SDIO pins to prevent them from being in a state that confuses the WiFi part. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-06nitrogen6x: simplify board_mmc_getcdTroy Kisky
The same logic applies to both SD card slots, only with different GPIOs and the code should make that easier to see. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2014-10-06nitrogen6x: implement board_cfb_skip() to disable text outputEric Nelson
Several customers have asked to leave the display quiet during boot, so allow the user to express this request by the presence of environment variable "novideo". Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-14 07:09:38 +0000