| Age | Commit message (Collapse) | Author |
|---|
|
Versal loadpdi command is used for loading secure & non-secure
pdi images.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Origin function was calling strsep which replaced delimiter ',' by a null
byte ('\0'). Operation was done directly on FDT which ends up with the
following behavior:
ZynqMP> printenv fdtfile
fdtfile=xilinx/zynqmp.dtb
ZynqMP> fdt addr $fdtcontroladdr
ZynqMP> fdt print / compatible
compatible = "xlnx", "zynqmp"
As is visible fdtfile was correctly composed but a null byte caused that
xlnx was separated from zynqmp.
This hasn't been spotted because in all Xilinx DTs there are at least 3
compatible string and only the first one was affected by this issue.
But for systems which only had one compatible string "xlnx,zynqmp" it was
causing an issue when U-Boot's DT was used by Linux kernel.
The patch removes strsep calling and strchr is called instead which just
locate the first char after deliminator ',' (variable called "name").
And using this pointer in fdtfile composing.
Fixes: 91d7e0c47f51 ("arm64: zynqmp: Create fdtfile from compatible string")
Reported-by: Igor Lantsman <igor.lantsman@opsys-tech.com>
Signed-off-by: Igor Lantsman <igor.lantsman@opsys-tech.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
On system with PL DDR which is placed before PS DDR in DT
env_get_bootm_size() and env_get_bootm_low() without specifying bootm_low
and bootm_size variables are taking by default gd->bd->bi_dram[0].start and
gd->bd->bi_dram[0].size. As you see 0 means bank 0 which doesn't need to be
PS ddr and even can be memory above 39bit VA which is what U-Boot supports
now.
That's why setup bootm variables based on ram_base/ram_size setting to make
sure that boot images are placed to the same location as U-Boot is placed.
This location should be by default location where OS can boot from.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Free resources used by Xen board before jumping to Linux kernel.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Make required updates to run on u-boot.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
|
|
Make required updates to run on u-boot and strip test code.
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
|
|
Add support for Xen para-virtualized serial driver. This
driver fully supports serial console for the virtual machine.
Please note that as the driver is initialized late, so no banner
nor memory size is visible.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Introduce a minimal Xen guest board running as a virtual
machine under Xen Project's hypervisor [1], [2].
Part of the code is ported from Xen mini-os and also uses
work initially done by different authors from NXP: please see
relevant files for their copyrights.
[1] https://xenbits.xen.org
[2] https://wiki.xenproject.org/
Signed-off-by: Andrii Anisov <andrii_anisov@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
|
|
It's better to keep all SPL related functions in the same spl.c.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Leo Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
|
|
This option was enabled during the earlier U-Boot porting time. Now
we already have the OTP driver in place and the unique MAC address
is read from the OTP, there is no need to turn on this option.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Leo Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
|
|
All FU540 driver related options should be in the SoC level Kconfig.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
|
|
spl_soc_init() seems to be a better name, as all SPL functions
names start from the spl_ prefix.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
|
|
Use the generic board_init_f() provided by the RISC-V library codes.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Use IS_ENABLED to prevent ifdef in board_key_check for STM32MP
- Add STM32 FMC2 EBI controller driver
- Fix dwc3-sti-glue which allows STiH410-B2260 to boot again
- Add fitImage its entry for 587-200 DHCOR SoM
- Add both PDK2 and DRC02 DT into DHCOM fitImage its
- Fix DHCOM KS8851 ethernet MAC address
- Remove stm32mp1 board.c file
- Use const for struct node_info in board stm32mp1.c file
|
|
Use const for the variable nodes in ft_board_setup,
this patch follow fdt_fixup_mtdparts prototype and no more use stack.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Remove the file board/st/stm32mp1/board.c which is not more
compiled since commit 156732cc8939 ("board: stm32mp1: move the
function board_debug_uart_init in spl.c")
Fixes: 4fb46816c7e2 ("board: stm32mp1: move the function board_debug_uart_init in spl.c")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
The STM32MP1 DHCOM has two ethernet interfaces, the on-SoM DWMAC and KS8851.
Set eth1addr for the KS8851 to a MAC address of the DWMAC incremented by 1.
The MAC of the DWMAC is set from on-SoM EEPROM already, but the MAC address
of KS8851 was left uninitialized, so fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
The new 587-200 DHCOR SoM is compatible with the 587-100 prototype,
hence just replicate the entries, as there is no pattern matching.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Include both PDK2 and DRC02 DTs in the DHCOM fitImage .its and implement
support in SPL to select the correct configuration entry for U-Boot by
using the machine compatible string from SPL DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This patch adds "st,stm32mp1-fmc2-nfc" compatible string in the
fdt fixup partitions table.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Use IS_ENABLED to prevent ifdef in ft_board_setup.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Use IS_ENABLED to prevent ifdef in env functions:
- env_get_location
- env_ext4_get_intf
- mmc_get_env_dev
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Use IS_ENABLED to prevent ifdef in board_late_init.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Use IS_ENABLED to prevent ifdef in dk2_i2c1_fix.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Use CONFIG_IS_ENABLED to prevent ifdef in set_dfu_alt_inf.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Use IS_ENABLED to prevent ifdef in sysconf_init.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Use IS_ENABLED to prevent ifdef in board_check_usb_power.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
g_dnl_board_usb_cable_connected
Use IS_ENABLED to prevent ifdef in g_dnl_board_usb_cable_connected
and in g_dnl_bind_fixup
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Use IS_ENABLED to prevent ifdef in board_key_check
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
On J7200 SoC OSPI0 and HypeFlash are muxed at HW level and only one of
them can be used at any time. J7200 EVM has both HyperFlash and OSPI
flash on board. There is a user switch (SW3.1) that can be toggled to
select OSPI flash vs HyperFlash.
Read the state of this switch via wkup_gpio0_6 line and fixup the DT
nodes to select OSPI0 vs HyperFlash
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add initial A72 defconfig support.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add initial R5 defconfig support
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add board detection support for j7200 common processor board.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
|
|
j7200-evm has minor differences with j721e-evm based on the IPs
available in the SoC. Introduce separate build targets for j7200-evm
to incorporate the differences.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
|
|
The DT nodes on J721E SoCs currently use a node name "interconnect" for
the various interconnects. This name is not following the DT schema, and
should simply be "bus". Update the fdt fixup logic to use both the current
and the expected corrected path names so that this logic won't be broken
with newer kernels.
Signed-off-by: Suman Anna <s-anna@ti.com>
|
|
Guard all eeprom probe with TI_I2C_BOARD_DETECT to avoid reading eeprom
when eeprom is not available
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
Current usage of eeprom apis produce a build failure when
CONFIG_TI_I2C_BOARD_DETECT is not defined. Add stub function for these
apis to avoid build failures.
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Because of space constraints, create a new USB defconfig for R5 to
faciliate booting from USB mass storage devices
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
Because of space constraints, create a new USB defconfig for R5 to
faciliate booting in USB peripheral (DFU) bootmode
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
The DT nodes on AM65x SoCs currently use a node name "interconnect" for
the various interconnects. This name is not following the DT schema, and
should simply be "bus". Update the fdt fixup logic to use both the
current and the expected corrected path names so that this logic won't
be broken with newer kernels.
The logic also corrects the crypto node name as the DT node
unit-addresses are all expected to be lower case.
Signed-off-by: Suman Anna <s-anna@ti.com>
|
|
This commit completes the migrations for DM_ETH and DM_USB. The board
is now consistent with omap3_beagle and other remaining OMAP3 boards.
Cc: Tom Rini <trini@konsulko.com>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
|
|
Move all assignments to gd->bd->bi_mem{start,size} to generic code in
setup_bdinfo.
Xtensa architecture is special in this regard as it defines its own
handling of gd->bd->bi_mem{start,size} fields. In order to avoid defining
a weak SDRAM function, let arch_setup_bdinfo overwrite the generic flags.
For ARC architecture, remove ARCH_EARLY_INIT_R from Kconfig since it is
not needed anymore.
Also, use gd->ram_base to populate bi_memstart to avoid an ifdef.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Acked-by: Alexey Brodkin <abrokdin@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add Luka Perkov to CRS3xx-98DX3236 MAINTAINERS.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
MikroTik CRS328-4C-20S-4S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
MikroTik CRS326-24G-2S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
MikroTik CRS305-1G-4S Bit board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
The Bit board variant is added, which has a bigger Macronix flash.
Add basic U-Boot, UART and Winbond SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
For 2020.10
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
|
|
This header file should not be included in other header files. Remove it
from each one and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We only need to include this header once. Drop the duplicate.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
