| Age | Commit message (Collapse) | Author |
|---|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The CONFIG_PHY_FIXED is necessary to allow DSA switch work in U-Boot after
the
commit 3bf135b6c367 ("drivers: net: phy: Ignore PHY ID 0 during PHY probing").
This particular device - LAN9303 - returns phy_id == 0. With
CONFIG_PHY_FIXED enabled HSC and DDC boards work again with the same U-Boot
binary.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Move this symbol to Kconfig. As part of this we can drop a UBI-specific
symbol that was a stop-gap for not having this particular symbol in
Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This patch disables support for running EFI applications on HSC|DDC boards.
As a result - considerable size reduction (~14%) has been observed (for
for u-boot-dtb.imx 475KiB to 407KiB).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Converted to use fsl_esdhc_imx for i.MX platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
|
|
Porting to DM and i.MX8
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_USB_EHCI_MX5
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
This commit enables the DM_USB on HSC|DDC i.MX53 based boards.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
The CONFIG_FSL_ESDHC is now enabled and defined in Kconfig, not in
include/configs/kp_imx53.h
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This commit updates the defconfig for the HSC and DDC
boards.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This commit adds support for DDC and HSC boards from
K+P in u-boot.
Console output:
U-Boot 2018.05-rc2-00090-g752b7ed6f9 (Apr 26 2018 - 14:24:24 +0200)
CPU: Freescale i.MX53 rev2.1 at 800 MHz
Reset cause: WDOG
Model: K+P iMX53
DRAM: 512 MiB
MMC: FSL_SDHC: 0
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Module EEPROM:
ID: TQMa53-CB.0401
SN: 63152762
MAC: 00:0b:64:03:14:2a
BBoard:40x0 Rev:10
Net: eth0: ethernet@63fec000
Hit any key to stop autoboot: 0
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
