aboutsummaryrefslogtreecommitdiff
path: root/configs/rock960-rk3399_defconfig
AgeCommit message (Collapse)Author
2024-05-07rockchip: rk3399: Migrate to OF_UPSTREAMJonas Karlman
All RK3399 boards has now been synced to Linux kernel v6.8 DTs and can migrate to use OF_UPSTREAM. Migrate RK3399 boards that exists in Linux v6.8 to use OF_UPSTREAM. Following target is not migrated to use OF_UPSTREAM: - nanopi-m4-2gb-rk3399: DDR3 variant of nanopi-m4-rk3399 (LPDDR3) Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2024-05-07rockchip: rk3399-rock960: Sync DT from v6.8 and update defconfigJonas Karlman
Sync rk3399-rock960 related device tree from Linux kernel v6.8. Add DM_RESET=y to support reset signals. Add PCI=y, CMD_PCI=y and NVME_PCI=y to support PCIe and NVMe boot. Add AHCI=y, SCSI_AHCI=y, AHCI_PCI=y and SCSI=y to support PCIe SATA boot. Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB. Remove CONFIG_NET_RANDOM_ETHADDR=y, ethaddr and eth1addr is set based on cpuid read from eFUSE. Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC. Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY. Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY. Remove REGULATOR_PWM=y and DM_REGULATOR_GPIO=y, boards does not use pwm-regulator or regulator-gpio compatible. Add USB_XHCI_HCD=y, USB_DWC3=y and USB_DWC3_GENERIC=y to support USB3. Remove USE_PREBOOT=y to speed up booting, standard boot will init USB after faster boot media has been evaluated. Add CMD_ROCKUSB=y, CMD_USB_MASS_STORAGE=y and USB_GADGET=y to support RockUSB and UMS gadget. Remove SPL_TINY_MEMSET=y to use full memset in SPL. Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2024-05-07rockchip: rk3399: Fix loading FIT from SD-card when booting from eMMCJonas Karlman
When RK3399 boards run SPL from eMMC and fail to load FIT from eMMC due to it being missing or checksum validation fails there can be a fallback to read FIT from SD-card. However, without proper pinctrl configuration reading FIT from SD-card may fail: U-Boot SPL 2024.04-rc4 (Mar 17 2024 - 22:54:45 +0000) Trying to boot from MMC2 mmc_load_image_raw_sector: mmc block read error Trying to boot from MMC2 mmc_load_image_raw_sector: mmc block read error Trying to boot from MMC1 Card did not respond to voltage select! : -110 mmc_init: -95, time 12 spl: mmc init failed with error: -95 SPL: failed to boot from all boot devices (err=-6) ### ERROR ### Please RESET the board ### Fix this by tagging related sdhci, sdmmc and spi flash pinctrl nodes with bootph props. Also move bootph for common nodes shared by all boards to the SoC u-boot.dtsi. eMMC, SD-Card and SPI flash nodes are also changed to only be tagged with bootph props for SPL and U-Boot pre-reloc phases. Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2024-05-07rockchip: rk3399: Enable random generator on all boardsJonas Karlman
The RK3399 SoC contain a crypto engine block that can generate random numbers. Imply DM_RNG and RNG_ROCKCHIP Kconfig options to take advantage of the random generator on all RK3399 boards. Also remove the unnecessary use of a status = "okay" prop. Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> Reviewed-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Dragan Simic <dsimic@manjaro.org>
2024-03-14rockchip: vamrs: rock960: Migrate to use IO-domain driverJonas Karlman
Switch to use the IO-domain driver to configure IO-domain based on device tree instead of a setup_iodomain() function. Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2024-03-14rockchip: Use common bss and stack addresses on RK3399Jonas Karlman
With the stack and text base used by U-Boot SPL and proper on RK3399 there is a high likelihood of overlapping when U-Boot proper + FDT nears or exceeded 1 MiB in size. Currently the following memory layout is typically used on RK3399: [ 0, 256K) - SPL binary [ 256K, 2M) - TF-A / reserved [ 2M, +X) - U-Boot proper binary (TEXT_BASE) [ -X, 3M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR) [ -16K, 3M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN) [ -X, 4M) - SPL pre-reloc stack (SPL_STACK) [ -16K, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN) [ 4M, +8K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE) [ -X, 64M) - SPL reloc stack (SPL_STACK_R_ADDR) [ 63M, 64M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN) SPL can safely load U-Boot proper + FDT to [2M, 4M-16K) with this layout. However, the stack at [-X, 3M) used during U-Boot proper pre-reloc is restricting the safe size of U-Boot proper + FDT to be less than 1 MiB. Migrate to use common bss, stack and malloc heap size and addresses to fix this restriction and allow for a larger U-Boot proper image size. Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2024-03-14rockchip: rk3399: regenerate defconfigsChen-Yu Tsai
Regenerate RK3399 defconfigs after adding imply statements. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Christopher Obbard <chris.obbard@collabora.com> Reviewed-by: Dragan Simic <dsimic@manjaro.org> Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
2024-01-19configs: rockchip: Use dwc3-generic driver on RK3328 and RK3399Jonas Karlman
Complete the transition away from xhci-dwc3 and dwc3-of-simple drivers and change to use the dwc3-generic driver on remaining RK3328 and RK3399 boards. MISC, USB_DWC3 and USB_DWC3_GENERIC is enabled on boards that used to enable USB_XHCI_DWC3. USB_XHCI_DWC3 is dropped from updated boards along with the default y of USB_XHCI_DWC3_OF_SIMPLE. There is no intended change in functionality with this changes, USB 3.0 is expected to continue same as before this change. Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2024-01-03configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2023-10-02configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2023-07-28rockchip: rk3399: pass platform parameter to TF-A by default for new RK3399 ↵Quentin Schulz
boards Long are gone the times TF-A couldn't handle the FDT passed by U-Boot. Specifically, since commit e7b586987c0a ("rockchip: don't crash if we get an FDT we can't parse") in TF-A, failure to parse the FDT will use the fallback mechanism. This patch was merged in TF-A v2.4-rc0 from two years ago. New boards should likely have this option disabled or explicitly enable it in their respective defconfig. Because existing boards might depend on a TF-A version that predates v2.4, let's just enable this option in all RK3399 defconfigs. Maintainers of each board can decide for themselves if they would prefer to disable this option and allow U-Boot to pass the DT to TF-A. Cc: Quentin Schulz <foss+uboot@0leil.net> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-05-01configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2023-02-17configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-12-05Convert CONFIG_SYS_NS16550_MEM32 et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_NS16550_MIN_FUNCTIONS CONFIG_SYS_NS16550_MEM32 CONFIG_SYS_NS16550_PORT_MAPPED CONFIG_SYS_NS16550_REG_SIZE CONFIG_SYS_NS16550_SERIAL To do this we also introduce CONFIG_SPL_SYS_NS16550_SERIAL so that platforms can enable the legacy driver here for SPL. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-11-03usb: ohci: Use a flexible array member for portstatusSamuel Holland
The struct is only used to overlay the MMIO region, so the behavior is the same. This obsoletes the Kconfig option for the number of ports. Signed-off-by: Samuel Holland <samuel@sholland.org>
2022-10-31Rename CONFIG_SYS_TEXT_BASE to CONFIG_TEXT_BASESimon Glass
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE and this makes it imposible to use CONFIG_VAL(). Rename it to resolve this problem. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-10-30video: Rename CONFIG_DM_VIDEO to CONFIG_VIDEOSimon Glass
Now that all the old code is gone, rename this option. Driver model migration is now complete. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-08-23configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-07Convert CONFIG_USB_OHCI_NEW et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_OHCI_SWAP_REG_ACCESS CONFIG_SYS_USB_OHCI_CPU_INIT CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS CONFIG_SYS_USB_OHCI_SLOT_NAME CONFIG_USB_ATMEL CONFIG_USB_ATMEL_CLK_SEL_PLLB CONFIG_USB_ATMEL_CLK_SEL_UPLL CONFIG_USB_OHCI_LPC32XX CONFIG_USB_OHCI_NEW Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SPL_BSS_START_ADDR to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_BSS_START_ADDR Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SPL_STACK to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_STACK Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.hTom Rini
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR - Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack pointer directly, otherwise we use the common calculation. - On some platforms that were using the standard calculation but did not set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them. - On a small number of platforms that were not subtracting GENERATED_GBL_DATA_SIZE do so now via the standard calculation. - CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most board config header files. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SPL_BSS_MAX_SIZE et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_BSS_MAX_SIZE CONFIG_SPL_MAX_FOOTPRINT Note that the da850evm platforms were violating the "only use one" rule here, and so now hard-code their BSS limit. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SPL_PAD_TO et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SPL_PAD_TO CONFIG_SPL_MAX_SIZE CONFIG_TPL_PAD_TO CONFIG_TPL_MAX_SIZE Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the existing places. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SYS_PBSIZE to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_PBSIZE Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-21configs: set CONFIG_COUNTER_FREQUENCYPeng Fan
Set CONFIG_COUNTER_FREQUENCY according to COUNTER_FREQUENCY in config header file. Signed-off-by: Peng Fan <peng.fan@nxp.com> [trini: Re-run migration]
2022-04-08configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-02-10nvme: Split out PCI supportMark Kettenis
Apple SoCs have an integrated NVMe controller that isn't connected over a PCIe bus. In preparation for adding support for this NVMe controller, split out the PCI support into its own file. This file is selected through a new CONFIG_NVME_PCI Kconfig option, so do a wholesale replacement of CONFIG_NVME with CONFIG_NVME_PCI. Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Simon Glass <sjg@chromium.org> Tested on: Macbook Air M1 Tested-by: Simon Glass <sjg@chromium.org>
2021-08-31Convert CONFIG_SKIP_LOWLEVEL_INIT et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SKIP_LOWLEVEL_INIT CONFIG_SKIP_LOWLEVEL_INIT_ONLY In order to do this, we need to introduce SPL and TPL variants of these options so that we can clearly disable these options only in SPL in some cases, and both instances in other cases. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-31Convert CONFIG_SYS_LOAD_ADDR to KconfigTom Rini
Now that we have consistent usage, migrate this symbol to Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-06-28configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-27configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-03-30rockchip: rk3399: rock960: explicitly disable SPI flashPeter Robinson
The Rock960 doesn't have SPI flash on-board, but the bits get enabled by default which means when booting we get some errors. Explicitly disable it to stop the errors. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-15configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-01-29configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-01-21configs: rk3399: enable rng on firefly/rock960/rockpro64Peter Robinson
Enable the RNG on the Firefly, rock960 and RockPro64 devices to enable KASLR on devices that support it. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Cc: Akash Gajjar <akash@openedev.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
2020-11-09configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-30Merge tag 'u-boot-rockchip-20201031' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - New PX30 board: Engicam PX30.Core; - Fix USB HID support for rock960; - Remove host endianness dependency for rockchip mkimage; - dts update for rk3288-tinker; - Enable console MUX for some ROCKPi boards; - Add config-based ddr selection for px30;
2020-10-30rockchip: Rock960: fix up USB supportPeter Robinson
Fix up USB config options so keyboards and other USB devices work. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang<kever.yang@rock-chips.com> Change-Id: I34b0696e0ac7303186f20c83278dde340399b690
2020-10-09configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-08-08Convert CONFIG_SYS_MMC_ENV_DEV et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MMC_ENV_DEV CONFIG_SYS_MMC_ENV_PART Note that with this conversion we now have consistent behavior with respect to ensuring that we have always selected the correct MMC device and hardware partition. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-26configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-22rockchip: Enable PCIe/M.2 on rock960 boardJagan Teki
Due to board limitation some SSD's would work on rock960 PCIe M.2 only with 1.8V IO domain. So, this patch enables grf io_sel explicitly to make PCIe/M.2 to work. Cc: Tom Cubie <tom@radxa.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-04-28configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-02rockchip: Enable HDMI output on rk3399 board w/ HDMIJagan Teki
Enable config options and console setting to respective rk3399 board for HDMI output. Boards supported and tested on this patch are: - NanoPc T4 - NanoPi M4 - NanoPi Neo4 - ROC-RK3399-PC - Rock960 Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-01-30rockchip: rk3399: Enable DISPLAY_CPUINFOJagan Teki
RK3288, RK3399 are now support cpu-info, so enable DISPLAY_CPUINFO by default. Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-22configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-13 01:37:41 +0000