| Age | Commit message (Collapse) | Author |
|---|
|
Remove custom config options that are not particularly necessary.
Align them with OMAP3 defaults used on other boards (especially for
memory locations).
Also enable Thumb build to reduce the SPL size and remove the custom
prompt text.
This makes the config a lot more minimalistic, maintainable and easier
to read.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
The common EMIF init code used for DRA7xx does not explicitly fill
the gd->bd->bi_dram entries (like OMAP3 does), so there is no reason
to set an explicit number of DRAM banks which doesn't correspond to
anything in particular.
Remove the CONFIG_NR_DRAM_BANKS option from the concerned defconfigs.
The dram_init_banksize default implementation will be fine with the
default value for the config option.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
The number of DRAM banks was defined to the same value in each OMAP3
board defconfig, which is expected and hardcoded in the code. Move the
common definition to the Kconfig option declaration instead.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
The maximum SPL size was defined to the same value in each OMAP3
board defconfig. Move the common definition to the Kconfig option
declaration instead.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
The maximum U-Boot size was defined to the same value in each OMAP3
board defconfig. Move the common definition to the Kconfig option
declaration instead.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
The init stack pointer was defined to the same value in each DRA7xx
board defconfig. Move the common definition to the Kconfig option
declaration instead.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
The DRA7xx EVM board use a slightly different init stack pointer
address compared to the AM57xx EVM board, for no particular reason.
Align the address with the AM57xx EVM board (which matches the usual
offset to the end of SRAM used by other OMAP devices) prior to removing
it as a per-board option in a later commit.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
The init stack pointer was defined to the same value in each AM43xx
board defconfig. Move the common definition to the Kconfig option
declaration instead.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
The init stack pointer was defined to the same value in each AM33xx
board defconfig. Move the common definition to the Kconfig option
declaration instead.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
The AM33xx chiliboard and guardian boards use a slightly different
init stack pointer address compared to other AM33xx boards, for no
particular reason.
Align the address with other AM33xx boards prior to removing it as a
per-board option in a later commit.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
The init stack pointer was defined to the same value in each OMAP3
board defconfig. Move the common definition to the Kconfig option
declaration instead.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
The SPL text base was defined to the same value in each OMAP3 board
defconfig. Move the common definition to the Kconfig option
declaration instead.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-snapdragon
* Qualcomm platforms >~2016 gain support for the RPMh (Resource Power Manager)
peripheral which is used to control most regulators. The RB5 is now able to
power up its USB VBUS regulator via the rpmh regulator driver. Git history
from the original Linux driver is preserved for ease of maintenance.
* IPQ40xx SoCs gain ethernet networking support via the new ESS EDMA driver.
|
|
Enable RPMh, cmd-db, and RPMh regulators. Additionally enable
CMD_REGULATOR for debugging.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
|
|
Enable True Random Number Generator (TRNG) on E850-96 board. To do so:
1. Enable DM_RNG and RNG_EXYNOS for TARGET_E850_96
2. Add TRNG node to E850-96 device tree
3. Enable 'rng' command support for easy TRNG testing
TRNG node is already applied in Linux kernel device tree, but it hasn't
appeared in upstream dts yet. Add it in U-Boot override dtsi file
temporarily; it can be removed once it appears in upstream dts.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Enable DM_I2C to avoid board removal warning.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Enrico Leto <enrico.leto@siemens.com>
|
|
The conversion to DM_I2C is mandatory, rework to remove
use of legacy I2C API.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Cc: Holger Brunck <holger.brunck@hitachienergy.com>
Cc: Tomas Alvarez Vanoli <tomas.alvarez-vanoli@hitachienergy.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
This board has not been converted to CONFIG_DM_I2C by the deadline.
Remove it.
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This board has not been converted to CONFIG_DM_I2C by the deadline.
Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This board has not been converted to CONFIG_DM_I2C by the deadline.
Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This board has not been converted to CONFIG_DM_I2C by the deadline.
Remove it.
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rework to remove use of legacy I2C API.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Tom Rini <trini@konsulko.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/21728
- Conversions to DM_I2C and DM_SERIAL.
- Support for I2C3 and PWM1 for the imx6q clock driver.
- Improvements for udoo-neo
- Describe the i.MX93 CPU clocks in the devicetree to fix CPU clock printing
- Fix for SPI and NANC clk-imx8mn clock driver
|
|
Enable DM_SERIAL to avoid board removal warning.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
|
|
Rework to remove use of legacy I2C API. Also switch
to DM_SERIAL to avoid board removal warning.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
|
|
Rework to remove use of legacy I2C API. Also switch
to DM_SERIAL to avoid board removal warning.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
|
|
Instead of using the local imx6sx-udoo-neo devicetree copies from U-Boot,
convert the imx6sx-udoo-neo boards to OF_UPSTREAM so that the upstream
kernel devicetrees can be used instead.
Tested on a imx6sx-udoo-neo-full board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
|
|
The udoo_neo_defconfig target supports several board variants.
All of these variants use the imx6sx-udoo-neo-basic devicetree in U-Boot.
Currently, the devicetree model as well as the board variant name
are shown:
...
Model: UDOO Neo Basic
Board: UDOO Neo FULL
...
Printing the devicetree model that is used internally by U-Boot
may confuse users.
Unselect the CONFIG_DISPLAY_BOARDINFO option and move the board printing
inside board_init() so that only the real board name that is detected
in run-time is printed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
|
|
u-boot.img has grown in such a way that it overwrites the
environment region.
Select CONFIG_LTO to help reducing the U-Boot binary size
and add a build-time size check to avoid U-Boot to overlap
the environment region.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
|
|
Commit 68dcbdd594d4 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
With the watchdog driver model in place, it is no longer needed
to have board code to initialize the watchdog, so remove
its related board code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
|
|
Daniel Schultz <d.schultz@phytec.de> says:
The overlays are specified in the bootenv.txt file that is loaded into
the environment. Then these overlays get loaded and applied via a script.
These scripts for loading and applying devicetree overlays are identical
for many phytec boards.
Create a common overlays.env that can be included.
Add support for devicetree overlays to phycore-imx8mp and include the
overlays.env for phycore-imx93.
Rename existing environment variables according to bootstd doc.
Move MMC boot logic into a common k3_mmc.env file and include the new
overlays.env file as well.
|
|
Add support for loading bootenv.txt as well as loading and applying
overlays during boot from mmc and net.
${no_bootenv}: Prevent loading external bootenv.txt environment. Use
${overlays} variable directly from u-boot environment.
${no_overlay}: Do not load overlays defined in ${overlays} variable.
Overlays loaded over the extension command are still
being applied.
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
|
|
Increase malloc size to 32 MB to align with other J7
family devices.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
|
|
This is an older platform and as we need to save space on it from time
to time, disable VBE boot support.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Mattijs Korpershoek <mkorpershoek@baylibre.com> says:
Android boot flow is a bit different than a regular Linux distro.
Android relies on multiple partitions in order to boot.
A typical boot flow would be:
1. Parse the Bootloader Control Block (BCB, misc partition)
2. If BCB requested bootonce-bootloader, start fastboot and wait.
3. If BCB requested recovery or normal android, run the following:
a. Get slot (A/B) from BCB
b. Run AVB (Android Verified Boot) on boot partitions
c. Load boot and vendor_boot partitions
d. Load device-tree, ramdisk and boot
The AOSP documentation has more details at [1], [2], [3]
This has been implemented via complex boot scripts such as [4].
However, these boot script are neither very maintainable nor generic.
Moreover, DISTRO_DEFAULTS is being deprecated [5].
Add a generic Android bootflow implementation for bootstd.
For this initial version, only boot image v4 is supported.
This has been tested on sandbox using:
$ ./test/py/test.py --bd sandbox --build -k test_ut
This has also been tested on the AM62X SK EVM using TI's Android SDK[6]
To test on TI board, the following (WIP) patch is needed as well:
https://gitlab.baylibre.com/baylibre/ti/ti-u-boot/-/commit/84cceb912bccd7cdd7f9dd69bca0e5d987a1fd04
[1] https://source.android.com/docs/core/architecture/bootloader
[2] https://source.android.com/docs/core/architecture/partitions
[3] https://source.android.com/docs/core/architecture/partitions/generic-boot
[4] https://source.denx.de/u-boot/u-boot/-/blob/master/include/configs/meson64_android.h
[5] https://lore.kernel.org/r/all/20230914165615.1058529-17-sjg@chromium.org/
[6] https://software-dl.ti.com/processor-sdk-android/esd/AM62X/09_02_00/docs/android/Overview.html
|
|
Add a unit test for testing the Android bootmethod.
This requires another mmc image (mmc7) to contain the following partitions:
- misc: contains the Bootloader Control Block (BCB)
- boot_a: contains a fake generic kernel image
- vendor_boot_a: contains a fake vendor_boot image
Also add BOOTMETH_ANDROID as a dependency on sandbox so that we can test
this with:
$ ./test/py/test.py --bd sandbox --build -k test_ut # build the mmc7.img
$ ./test/py/test.py --bd sandbox --build -k bootflow_android
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Julien Masson <jmasson@baylibre.com>
Reviewed-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
https://source.denx.de/u-boot/custodians/u-boot-rockchip
- Add boards:
rk3328: Radxa ROCK Pi E v3;
rk3588s: FriendlyElec NanoPi R6C/S;
- Remove board: Theobroma Systems RK3368 Lion;
- Add rk3588 pcie support;
- Misc updates for board and config;
CI: https://source.denx.de/u-boot/custodians/u-boot-rockchip/-/pipelines/2163
|
|
Instead of cluttering up a header file with a bunch of defines,
move the default environmental variables to a file called
am3517evm.env and reference it from the defconfig. Also
remove dead comments.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Enable USB host as well as USB gadget and DFU support for a53 and r5
configs. Also, enable UUU fastboot support to download files with
the UUU tool from a53.
Additionally, configure usb0 to peripheral mode and add extra
environment for DFU use.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
|
|
for rk3308, all defconfigs have CONFIG_OF_LIBFDT_OVERLAY=y, so enable it
by default.
for rk3328, any defconfig doesn't have it. but there is no strong reason
not to enable it. at least it's required for ROCK Pi E.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The NanoPi R6S is a SBC by FriendlyElec based on the Rockchip RK3588s.
It comes with 4GB or 8GB of RAM, a microSD card slot, 32GB eMMC storage,
one RTL8211F 1GbE and two RTL8125 2.5GbE Ethernet ports, one USB 2.0
Type-A and one USB 3.0 Type-A port, a HDMI port, a 12-pin GPIO FPC
connector, a fan connector, IR receiver as well as some buttons and LEDs.
Add initial support for this board using the upstream devicetree sources.
Kernel commit:
f1b11f43b3e9 ("arm64: dts: rockchip: Add support for NanoPi R6S")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
|
|
The NanoPi R6C is a SBC by FriendlyElec based on the Rockchip RK3588s.
It comes with 4GB or 8GB of RAM, a microSD card slot, optional 32GB eMMC
storage, one M.2 M-Key connector, one RTL8211F 1GbE and one RTL8125
2.5GbE Ethernet port, one USB 2.0 Type-A and one USB 3.0 Type-A port, a
HDMI port, a 30-pin GPIO header as well as multiple buttons and LEDs.
Add initial support for this board using the upstream devicetree sources.
Tested in U-Boot proper:
- Booting from eMMC works
- 1GbE Ethernet works using the eth_eqos driver (tested by ping)
- 2.5GbE Ethernet works using the eth_rtl8169 driver (tested by ping),
but the status LEDs on this specific port currently aren't working
- NVMe SSD in M.2 socket does get recognized (tested with `nvme scan`
followed by `nvme details`)
Kernel commit:
d5f1d7437451 ("arm64: dts: rockchip: Add support for NanoPi R6C")
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
|
|
This enables PCIe support on Tiger as exposed on
Q7_PCIE[0123]_[RT]X_[PN] signals and more specifically on the `PCI
Express` connector on the Haikou devkit.
This was tested with a PCIe to NVMe adapter (e.g.
https://www.amazon.de/dp/B07RZZ3TJG).
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Jaguar has an M.2 M-KEY slot for NVMes, connected to the PCIe3 4-lane
PHY on RK3588.
CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y is technically not necessary since
it's required only for the M.2 E-KEY slot on the main PCB, but that is
used typically for WiFi+BT modules, or on the mezzanine connector but
the features exposed behind that connector aren't supported in U-Boot
(no DT for it right now). However, if the PHY driver is missing, we get
the following error message:
pcie_dw_rockchip pcie@fe170000: failed to get pcie phy (ret=-19)
and you would need to know which PCIe controller that is before deciding
to ignore it. While after enabling the PHY driver, we are greeted with:
pcie_dw_rockchip pcie@fe170000: PCIe-2 Link Fail
which is a bit more acceptable (to me).
The other option would be to disable the PCIe2 PHYs/controllers in the
DT, which I'm not too fond of.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
ROCK Pi E v3.0 uses DDR4 SDRAM instead of DDR3 SDRAM used in v1.2x.
prepare new rk3328-rock-pi-e-v3.dts in u-boot which just includes
upstream rk3328-rock-pi-e.dts.
defconfig still uses
CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-rock-pi-e.dtb"
because v3.0 and prior are compatible.
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
No meaningful changes were made to this SoM since February 2021. Nobody
from Theobroma has booted anything recent on that product since July
2021 at the latest. The product isn't available to buy anymore and
disappeared from our website.
This product is therefore unmaintained and it would be disingenuous to
say the opposite, so drop support for RK3368 Lion.
If you're a user of Lion, feel free to revert this patch or contact our
sales/support department.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
On Puma v2.1 with a KSZ9031, the Ethernet PHY often doesn't detect the
link in the 4-second default timeout.
After some boot-loop test for about a thousand boots, 70% were below
10s, 90% below 15s and 100% below 30s. Let's play it safe and make it
30s so that hopefully all links that should be detected are.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Enable the IO domain on Ringneck. Based on the current HW design, this
should do nothing else than making sure vccio6 iodomain is controlled by
the GRF and not GPIO0B6.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The Haikou Devkit exposes 4 buttons over GPIO so let's enable their
support so their status can be queried from the `button` command from
the CLI.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
