| Age | Commit message (Collapse) | Author |
|---|
|
LS1043AQDS Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 DIMM
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* Two RGMII ports
* XFI 10G port
* SGMII
* QSGMII with 4x 1G ports
PCIe: supports Gen 1 and Gen 2
SATA 3.0: one SATA 3.0 port
USB 3.0: two micro AB connector and one type A connector
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
[York Sun: Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Reuse dts files from ls1043a linux kernel. Some parts in dts files
may not be needed by U-Boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Enabling the new tiny-printf function makes the SPL image fit again in
the 8KiB restricted area.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
|
|
There are already Kconfig options for SPI flash drivers, but we
have not moved them from config.h to defconfig files. This commit
does this in a batch.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
There are already Kconfig options for SPI drivers, but we
have not moved them from config.h to defconfig files. This
commit does this in a batch.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
After introduction of CONFIG_SYS_NS16550 these defconfig files were
added and need to be updated.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such
on the PCB, is meant as a A20 based router board. As such the board comes
with a built-in switch chip giving it 5 gigabit ethernet ports, and it
has a large empty area on the pcb with mounting holes which will fit a
2.5 inch harddisk. To complete its networking features it has a
Realtek RTL8192CU for WiFi 802.11 b/g/n.
The dts file is identical to the one submitted upstream.
Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add defconfig files for the Orangepi Plus and Orangepi PC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add support for storing the environment in CFI NOR flash on Juno and FVP
models.
I also removed some config values that are not used by CFI flash parts.
Juno has 1 flash part with 259 sectors. The first 255 sectors are
0x40000 (256kb) and are followed by 4 sectors of 0x10000 (64KB).
FVP models simulate a 64MB NOR flash part at base address 0x0FFC0000.
This part has 256 x 256kb sectors. We use the last sector to store the
environment.
To save the NOR flash to a file, the following parameters should be
passed to the model:
-C bp.flashloader1.fname=${FILENAME}
-C bp.flashloader1.fnameWrite=${FILENAME}
Foundation models don't simulate the NOR flash, but having NOR support
in the u-boot binary does not harm: attempting to write to the NOR will
fail gracefully.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Change to ns16550 uart for 10m50 devboard based on a new
Altera release.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
|
|
Zap CONFIG_NS16550_SERIAL, as the unification of ns16550 drivers
is completed.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Unify serial_x86, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Enable the USB keyboard on sandbox, now that we have a suitable emulation
driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Allow console recording so that tests can use it. Also allow the console
output to be suppressed, to reduce test output 'noise'.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add a sandbox timer which get time from host os and a basic
test.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
No UART driver was specified in defconfig, thus
DEBUG_UART_ALTERA_JTAGUART was incorrectly selected by default since
commit 220e8021af96741bd7149ca9895e1f0c8a38d0bb added a new Altera UART
driver.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
This board uses the same CPU (8309) as VECT1. The memory however is
different since it has NAND Flash, the NOR Flash partitioning is
different and of course the FPGAs as well.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Christoph Dietrich <christoph.dietrich@keymile.com>
|
|
This board is similar to TUXX1, but it has differend FPGAs.
Signed-off-by: Christoph Dietrich <christoph.dietrich@keymile.com>
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
|
|
Add CMD_GPIO to Kconfig and run tools/moveconfig.py .
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
BeagleBoard X15 (http://beagleboard.org/x15) support in u-boot does
actually support two different platform configuration offered by
TI. In addition to BeagleBoard X15, it also supports the TMDXEVM5728
(or more commonly known as AM5728-evm).
Information about the TI AM57xx EVM can be found here
http://www.ti.com/tool/tmdxevm5728
The EVM configuration is 1-1 compatible with BeagleBoard X15 with the
additional support for mPCIe, mSATA, LCD, touchscreen, Camera, push
button and TI's wlink8 offering.
Hence, we rename the beagle_x15 directory to am57xx to support TI
EVMs that use the AM57xx processor. By doing this we have common code
reuse. This sets the stage to have a common u-boot image solution for
multiple TI EVMs such as that already done for am335x and am437x. This
sets the stage for upcoming multiple TI EVMs that share the same code
base.
NOTE: Commit eae7ae185335 ("am437x: Add am57xx_evm_defconfig using
CONFIG_DM") introduced DT support for beagle_x15 under am57xx_evm
platform name. However, this ignored the potential confusion arising for
users as a result. To prevent this, existing beagle_x15_defconfig is
renamed as am57xx_evm_nodt_defconfig to denote that this is the "non
device tree" configuration for the same platform. We still retain
am57xx-beagle-x15.dts at this point, since we just require the common
minimum dts.
As a result of this change, users should expect changes in build
procedures('make am57xx_evm_nodt_defconfig' instead of 'make
beagle_x15_defconfig'). Hopefully, this would be a one-time change.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
|
|
Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
|
|
For Marvell plugs, move the configuration of DHCP, NAND/SF, PING
and USB commands, and HUSH_PARSER into the _defconfig file, rather
than the include/configs/*plug.h files.
This avoids compiler warnings of duplicate definitions if the
option is selected in the .config, but also defined in the
include/configs/*plug.h file.
Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
|
|
With this change Synopsys DesignWare SDP board is switched to driver
model for both serial port (serial_dw) and Ethernet (Designware GMAC).
This simplifies include/configs/axs101.h and allows for reuse of Linux's
Device Tree description.
For simplicity Linux's .dts files are not blindly copied but only very
few extracts of them are really used (those that are supported in U-Boot
at the moment).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
|
|
Move to driver model for ETH (e1000) on QEMU.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Move to driver model for USB on QEMU.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Move to driver model for pci on QEMU.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Francois Retief <fgretief@spaceteq.co.za>
|
|
Add an initr function in the board_r.c file for the AMBA Plug&Play
command. Add a Kconfig entry for the ambapp command and remove all
CONFIG_CMD_AMBAPP defines from the board configuration headers.
Add a Kconfig entry to display the AMBA Plug&Play information
on startup. This option is off by default. Remove relevent define
from board configuration headers.
Signed-off-by: Francois Retief <fgretief@spaceteq.co.za>
|
|
Update the GRSIM board with the memory settings for the evaluation
version of TSIM. This free version of TSIM is used for testing.
Signed-off-by: Francois Retief <fgretief@spaceteq.co.za>
|
|
hrcon DH(dual head) has two video outputs per FPGA.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
The gdsys strider board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 1x 10/100 Mbit/s Ethernet (optional)
- Lattice ECP3 FPGA connected via eLBC
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
[trini: Drop setting CONFIG_SYS_GENERIC_BOARD, this is always true now]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The Cubietruck has a mini-USB connector that can be used to power up the
board and as an OTG connector.
Since we have already some USB host-only ports right beside this one,
enable it in gadget mode
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A13-Olinuxino has a mini-USB connector that can be used to power up
the board and as an OTG connector.
Since we have already some USB host-only ports right beside this one,
enable it in gadget mode
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Since we don't have for sure a valid IP-setup during
board_late_init(...) because it maybe allready stored in environment or
not, we cannot form a proper vxWorks bootline at this place.
So we move to the way, forming the bootline just before
executing/launching vxWorks. To do this we use the bootvx command
instead go.
We only have to form the "othbootargs" environment variable, the rest is
done pretty good by the "bootvx" commannd.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
|
|
Rename board nios2-generic to 3c120_devboard. Since nios2 is
converted to driver model and device tree control of u-boot,
the nios2-generic board directory is removed. We can rename
the board back to a real board name. Now the boards maintained
in u-boot mainline are the same as Linux kernel, namely 3c120
and 10m50.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Add 10m50 devboard support. It is based on the Golden Hardware
Reference Design (GHRD), available at,
http://rocketboards.org/foswiki/view/Documentation/
AlteraMAX1010M50RevCDevelopmentKitLinuxSetup
Though we supported only one nios2-generic board in the past. Now,
with the removal of the nios2-generic board dir, adding new nios2
boards to u-boot is easier than before. It should be helpful to
add those boards supported in Linux mainline. There are only two
such nios2 boards, the 3c120 devboard and 10m50 devboard. The
nios2-generic is actually 3c120, and should restore the name. The
10m50 is this one.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Use cfi flash driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
|
|
Revert commit 7a2c1b13 which dropped OpenRD boards.
Assume maintainership of OpenRD.
Remove OpenRD from scrapyard.
Switch OpenRD to generic board.
Switch to Thumb build.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
|
|
Enable setexpr command in defconfig because it is really
useful as suggested by Marek.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Marek Vasut <marex@denx.de>
|
|
|
|
|
|
This board runs a P5020 or P5040 chip, and utilizes
an EEPROM with similar formatting to the Freescale P5020DS.
Large amounts of this code were developed by
Adrian Cox <adrian at humboldt dot co dot uk>
Signed-off-by: Andy Fleming <afleming@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Remove zc70x target which was one setting for zc702 and zc706.
Currently zc702 and zc706 are separated.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
|
