| Age | Commit message (Collapse) | Author |
|---|
|
On AM62x SK we can see a boot failure with signature "alloc space
exhausted", so fix by increasing size of SPL_STACK_R_MALLOC_SIMPLE_LEN.
Fixes: 128f81290b ("arm: dts: k3: binman: am625: add support for signing TIFSSTUB Images")
Signed-off-by: Judith Mendez <jm@ti.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
|
|
Add configs related to spi nor flash for Sophgo Milk-V Duo board
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Add configs related to ethernet and ethernet boot command for Sophgo Milk-V
Duo board
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Add sysreset configs as well as poweroff and reset commands for Sophgo
Milk-V Duo board.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Wadim Egorov <w.egorov@phytec.de> says:
Migrate the boards I maintain to OF_UPSTREAM.
|
|
The phycore-rk3288 can be migrated to OF_UPSTREAM.
Drop redundant device tree files, update MAINTAINERS and
defconfig's DEFAULT_DEVICE_TREE for rockchip vendor prefix accordingly.
Move device tree nodes required for u-boot to rk3288-phycore-rdk-u-boot.dtsi
such as chosen, i2c_eeprom_id and it's alias.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
|
|
The phycore-am64x can be migrated to OF_UPSTREAM.
Drop redundant device tree files, update MAINTAINERS and
defconfig's DEFAULT_DEVICE_TREE for ti vendor prefix accordingly.
While at it, drop the redundant definitions of AM642_PHYBOARD_ELECTRA_DTB
& SPL_AM642_PHYBOARD_ELECTRA_DTB from the binman dtsi file.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
|
|
The phycore-am62x can be migrated to OF_UPSTREAM.
Drop redundant device tree files, update MAINTAINERS and
defconfig's DEFAULT_DEVICE_TREE for ti vendor prefix accordingly.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
|
|
MD Danish Anwar <danishanwar@ti.com> says:
The series introduces device tree and config changes and AM65x
to enable ICSSG driver. The series also enables SPL_LOAD_FIT_APPLY_OVERLAY
for AM65x in order to load overlay over spl.
The ICSSG2 node is added in device tree overlay so that it remains in
sync with linux kernel.
This series has been tested on AM65x SR2.0, and the ICSSG interface is
able to ping / dhcp and boot kernel using tftp in uboot.
The users need to set env variables fw_storage_interface, fw_dev_part,
fw_ubi_mtdpart, fw_ubi_volume to indicate which storage medium and
partition they want to use to load firmware files from. By default the env
fw_storage_interface=mmc and fw_dev_part=1:2 but users can modify these
envs as per their requirements.
|
|
We want SPL to apply DTB overlays (e.g. ICSSG2 overlay) so enable
SPL_LOAD_FIT_APPLY_OVERLAY.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
|
|
Enable ICSSG driver in am65x_evm_a53_defconfig
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
|
|
Enable MMC UHS support for to allow to enter the UHS
modes for MMC1.
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
|
|
Convert to OF_UPSTREAM for i.MX93 11x11 EVK.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Enable PCIe/NVMe support on DH i.MX8M Plus DHCOM PDK3. Except for
the configuration options which are enabled, add slight adjustment
to board u-boot.dtsi, which is necessary as there is currently no
driver for the I2C PCIe clock generator. Since the generator is
strapped to be always on, it is possible to supplant the generator
functionality by fixed-clock.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
In commit 51aaaf5e7975 ("board: toradex: imx: Remove not needed env variables")
the empty definition of fdt_fixup variable was removed, however this was
still referenced from the boot command leading to boot failures:
## Error: \"fdt_fixup\" not defined`
Fix this by removing "run fdt_fixup" from the boot command and instead
enable CONFIG_OF_ENV_SETUP in the defconfig that would achieve the same
but in a more robust way (it works fine even if the variable is not
defined).
Fixes: 51aaaf5e7975 ("board: toradex: imx: Remove not needed env variables")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
|
|
RK356x-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
Since ft_board_setup isn't defined anymore, there's no need for
selecting CONFIG_OF_BOARD_SETUP.
Similarly, because the turing-rk1-rk3588.c would be empty, it is simply
removed, with the (would-be-empty) Makefile as well.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
Since ft_board_setup isn't defined anymore, there's no need for
selecting CONFIG_OF_BOARD_SETUP.
Similarly, because the toybrick_rk3588.c would be empty, it is simply
removed, with the (would-be-empty) Makefile as well.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
Since ft_board_setup isn't defined anymore, there's no need for
selecting CONFIG_OF_BOARD_SETUP.
Similarly, because the evb_rk3588.c would be empty, it is simply
removed, with the (would-be-empty) Makefile as well.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
All defconfigs using the CONFIG_TARGET_EVB_RK3588 are updated at once
since they are impacted by this change.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
Since ft_board_setup isn't defined anymore, there's no need for
selecting CONFIG_OF_BOARD_SETUP.
Similarly, because the rock5b-rk3588.c would be empty, it is simply
removed, with the (would-be-empty) Makefile as well.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
Since ft_board_setup isn't defined anymore, there's no need for
selecting CONFIG_OF_BOARD_SETUP.
Similarly, because the rock5a-rk3588s.c would be empty, it is simply
removed, with the (would-be-empty) Makefile as well.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
Since ft_board_setup isn't defined anymore, there's no need for
selecting CONFIG_OF_BOARD_SETUP.
Similarly, because the quartzpro64-rk3588.c would be empty, it is simply
removed, with the (would-be-empty) Makefile as well.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
Since ft_board_setup isn't defined anymore, there's no need for
selecting CONFIG_OF_BOARD_SETUP.
Similarly, because the nanopc-t6-rk3588.c would be empty, it is simply
removed, with the (would-be-empty) Makefile as well.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Some variants of the ROCK Pi 4 series have an SPI flash chip populated
which can be booted from. This patch enables support in U-Boot for
building the image for the SPI flash, support for booting U-Boot from the
SPI flash chip and support in U-Boot for accessing the SPI flash using
`sf` commands.
Not all variants (e.g. ROCK Pi 4B, ROCK 4 Model C Plus, ROCK 4SE) come
populated with an SPI flash chip, but have the footprint on the board so
a user could solder their own to the board. With this patchset applied,
these board variants without an SPI flash chip still boot from MMC.
I have enabled support for both Winbond and XTX SPI flash devices since
different hardware variants have different devices populated:
- `rockpi4_v13_sch_20181112.pdf` contains a Winbond part `W25Q64FWZPIG`
- `rockpi4_v14_sch_20210114.pdf` contains an XTX part `XT25F32BWOIGT`
The ROCK Pi 4 I have is marked as "ROCK PI 4 v1.48" and contains an SPI
flash chip from XTX:
=> sf probe
SF: Detected xt25f32 with page size 256 Bytes, erase size 4 KiB, total 4 MiB
In the interest of supporting all board variants and not regressing
existing users who boot from MMC, I have enabled support for booting from
both SPI flash chip variants in the defconfig and left the environment
storage location as MMC to not break existing users who have the
environment stored on MMC.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
|
|
Port the RK3328 part of the Rockchip IO-domain driver from linux.
This differs from linux version in that pmu io iodomain bit is enabled
in the write ops instead of in an init ops as in linux, this way we can
avoid keeping a full state of all supply that have been configured.
Enable by default on all RK3328 boards, skip rk3328-evb because this
target is typically also used on miscellaneous boards and boxes not
fully supported by U-Boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The generic RK35xx board targets are intended to be used as a bare
minimum target that can be used to e.g. boot boards that mostly follow
reference hw design before a board spefic target has been added or for
flashing and recovery purposes.
Disable BOOTMETH_VBE, NET and ADC as these features are not intended to
ever be used by these minimal generic board targets.
Enable SYSRESET_PSCI to let TF-A handle sysreset from U-Boot proper.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add support for USB OTG, RockUSB and UMS to the generic RK3588S/RK3588
target.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add support for USB OTG, RockUSB and UMS to the generic RK3566/RK3568
target.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add support for booting from SPI flash using the generic RK3566/RK3568
target.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Enable SPL_FIT_SIGNATURE=y and LEGACY_IMAGE_FORMAT=y to validate FIT
images checksum in SPL.
Change to SPL_MAX_SIZE=0x40000 to allow SPL up to 256 KiB in size.
Enable SPL_DM_SEQ_ALIAS=y and SPL_PINCTRL=y to ensure eMMC and SD-card
pinctrl is configured in SPL.
Enable SYS_NS16550_MEM32=y to use readl/writel in serial driver.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK35xx boards are expected to use the dwc3-generic driver and not the
xhci-dwc3 driver.
Remove the USB_XHCI_DWC3 option to ensure that the dwc3-generic driver
is used.
Fixes: 153ac950a599 ("board: rockchip: Add the Turing RK1 SoM")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Pinctrl must be configured for eMMC, SD-card and SPI flash to
successfully read FIT from all possible fallback media in SPL.
Include pinctrl props and enable the SPL_PINCTRL Kconfig option to
ensure FIT can be loaded from eMMC, SD-card and SPI flash.
Also enable the SPL_DM_SEQ_ALIAS Kconfig option to ensure that the
storage device sequence number matches in both SPL and U-Boot proper.
Fixes: 9fdd9a546986 ("board: rockchip: add Rockchip Toybrick TB-RK3588X board")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The SF_DEFAULT_SPEED Kconfig option got lost during merge and this
prevent reading FIT from SPI flash.
Restore the SF_DEFAULT_SPEED option to fix this.
Fixes: 8a94c376f6cb ("rockchip: Use common bss and stack addresses on RK356x")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Pinctrl must be configured for eMMC, SD-card and SPI flash to
successfully read FIT from all possible fallback media in SPL.
Include pinctrl props and enable the SPL_PINCTRL Kconfig option to
ensure FIT can be loaded from eMMC, SD-card and SPI flash.
Also enable the SPL_DM_SEQ_ALIAS Kconfig option to ensure that the
storage device sequence number matches in both SPL and U-Boot proper.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Pinctrl must be configured for eMMC, SD-card and SPI flash to
successfully read FIT from all possible fallback media in SPL.
Include pinctrl props and enable the SPL_PINCTRL Kconfig option to
ensure FIT can be loaded from eMMC, SD-card and SPI flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Imply BOOTSTD_FULL for all RK356x boards to more closely follow RK3588.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The RK35xx SoCs contain a crypto engine block that can generate random
numbers.
Enable rng node in soc u-boot.dtsi and enable Kconfig options to take
advantage of the random generator.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
SPL_ROCKCHIP_BACK_TO_BROM should normally only be enabled when BROM
should load U-Boot binary. SPL on Anbernic RGxx3 devices load TF-A and
U-Boot proper from FIT images and does never jump back to BROM from SPL.
Remove the superfluous Kconfig option from defconfig to align with other
RK356x boards.
This patch have no intended change in boot behavior.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588 boards do not have any pwm-regulator compatible nodes in DT, drop
the superfluous REGULATOR_PWM Kconfig options.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Update defconfig for rk3308-rock-pi-s with new defaults.
Add OF_LIBFDT_OVERLAY=y to support device tree overlays.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Remove BOOTDELAY=0, SYS_CONSOLE_INFO_QUIET=y and enable more CMD to
allow use of U-Boot cmdline.
Add DM_ETH_PHY=y and PHY_REALTEK=y to support onboard ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y, DM_USB_GADGET=y and remove USB_DWC2=y to
allow full use of USB 2.0 host and otg ports.
Enable EFI_LOADER to allow EFI boot.
Also fix use of USB 2.0 otg port by removing improper use of phy-supply
and regulator-always-on props.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Update defconfig for rk3308-roc-cc with new defaults.
Add OF_LIBFDT_OVERLAY=y to support device tree overlays.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Remove BOOTDELAY=0, SYS_CONSOLE_INFO_QUIET=y and enable more CMD to
allow use of U-Boot cmdline.
Add DM_ETH_PHY=y and PHY_REALTEK=y to support onboard ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y, DM_USB_GADGET=y and remove USB_DWC2=y to
allow full use of USB 2.0 host and otg ports.
Enable EFI_LOADER to allow EFI boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Update defconfig for rk3308-evb with new defaults.
Add OF_LIBFDT_OVERLAY=y to support device tree overlays.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Use DEBUG_UART_BASE=0xFF0E0000 and disable DEBUG_UART_BOARD_INIT to
make debug uart use uart4, same as stdout-path prop.
Remove BOOTDELAY=0, SYS_CONSOLE_INFO_QUIET=y and enable more CMD to
allow use of U-Boot cmdline.
Add DM_ETH_PHY=y and PHY_REALTEK=y to support onboard ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y, DM_USB_GADGET=y and remove USB_DWC2=y to
allow full use of USB 2.0 host and otg ports.
Enable EFI_LOADER to allow EFI boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
When RK3308 boards run SPL from eMMC and fail to load FIT from eMMC due
to it being missing or checksum validation fails there can be a fallback
to read FIT from SD-card. However, without proper pinctrl configuration
reading FIT from SD-card may fail:
U-Boot SPL 2024.04-rc4 (Mar 16 2024 - 12:36:12 +0000)
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC1
Card did not respond to voltage select! : -110
mmc_init: -95, time 12
spl: mmc init failed with error: -95
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices (err=-6)
### ERROR ### Please RESET the board ###
Fix this by tagging related emmc and sdmmc pinctrl nodes with bootph
props. Also sort and move common nodes shared by all boards to the SoC
u-boot.dtsi.
Imply SPL_PINCTRL and SPL_DM_SEQ_ALIAS to apply correct pinconf before
trying to load FIT from a device.
Move u-boot,spl-boot-order to soc u-boot.dtsi and define both sdmmc and
emmc nodes as fallback.
Also fix boot from eMMC (SD NAND) on ROCK Pi S by using correct pinctrl.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The RK3308 SoC support ARMv8 Cryptography Extensions and use of the
ARMv8 crypto extensions help speed up FIT checksum validation in SPL.
Imply ARMV8_SET_SMPEN and ARMV8_CRYPTO to take advantage of the crypto
extensions for SHA256 when validating checksum of FIT images.
Imply SPL_FIT_SIGNATURE and LEGACY_IMAGE_FORMAT to enable FIT checksum
validation on all RK3308 boards.
Also disable CONFIG_SPL_RAW_IMAGE_SUPPORT in board defconfigs to ensure
SPL does not try to jump to code that failed checksum validation.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-fsl-qoriq
- move to OF_UPSTREAM for sl28
|
|
Support is added for 5 new Qualcomm SoCs:
* QCM2290 and SM6115 are low and mid range SoCs used on the RB1 and RB2
respectively. SM6115 is also used in some mid-range smartphones/tablets.
Initial support includes buttons and USB (host and gadget).
* SM8250 is a flagship SoC from 2020 used on the RB5, as well as many flagship
smartphones. The board can boot to a U-Boot prompt, but is missing regulators
necessary for USB support.
* SM8550, and SM8650 are flagship mobile SoCs from 2023 and 2024
respectively. Found on many high end smartphones.
In addition:
* Support is added for the Schneider HMIBSC board.
* mach-snapdragon switches to OF_UPSTREAM
* IPQ40xx gets several regressions fixed and some overall cleanup.
* The MSM serial driver gains the ability to generate the bit-clock
automatically, no longer relying on a custom DT property.
* The Qualcomm SMMU driver gets a generic compatible (so per-SoC compatibles
don't need to be added).
* Support for the GENI I2C controller is added.
* The qcom SPMI driver has SPMI v5 support fixed, and v7 support added.
* The qcom sdhci driver gets some fixes for SDCC v5 support.
* SDM845 gains sdcard support
* Support is added for the Synopsys eUSB2 PHY driver (used on SM8550 and SM8650)
* SYS_INIT_SP_BSS_OFFSET is set to 1.5M to give us more space for FDTs.
* RB2 gets a work-around to fix the USB dr_mode property before booting Linux.
|
|
Use the new device devicetree files in dts/upstream/ and delete the old
ones. Still keep the -u-boot.dtsi with all u-boot specifics around.
There is one catch and that is fsl-ls1028a-kontron-sl28-var3.dts which
is not available upstream (yet!). For now, the base dts is used for this
variant as this only differ in the compatible and the (human readable)
model name.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Enable the GENI I2C driver in the default Qualcomm defconfig.
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
EFI initialisation fails without this, and with proper SMBIOS v3 support
in (and automatic generation of useful tables) there's no reason for us
not to do this on qcom platforms.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
