| Age | Commit message (Collapse) | Author |
|---|
|
Update the current uDPU defconfig with following changes:
* Disable CONFIG_SPI_BOOT, its not needed for booting and the device boots
from eMMC anyway.
* Disable CONFIG_SYS_CONSOLE_INFO_QUIET, there is no need to diverge from
other boards by not priting the console device
* Enable CONFIG_CMD_MTD in order to allow use of the MTD tool
* Disable CONFIG_CMD_MTDPARTS, with MTD now being able to parse partitions
from DTS there is no need for it, the default MTDPARTS were incorrect
anyway
* Enable CONFIG_MMC_HS200_SUPPORT, the eMMC used support both HS200 and
HS400 modes, so enable at least HS200 because Xenon driver does not
support HS400 currently
* Replace CONFIG_SPI_FLASH_BAR with CONFIG_SPI_FLASH_SFDP_SUPPORT
Utilize SFDP parsing instead of relying on the extended address registers
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Allow to read OTP bits via U-Boot fuse command on all Armada 3720 boards.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
As explained in commit 4af2a33ee5b9 ("cmd: gpio: Make `gpio input`
return pin value again") the `gpio input` is used in scripts to obtain
the value of a pin, despite the fact that CMD_RET_FAILURE is
indistinguishable from a valid pin value.
To be able to detect failures and properly use the value of a GPIO in
scripts we introduce the `gpio read` command that sets the variable
`name` to the value of the pin. Return code of the `gpio read` command
can be used to check for CMD_RET_SUCCESS or CMD_RET_FAILURE.
CONFIG_CMD_GPIO_READ is used to enable the `gpio read` command.
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
|
|
The most commonly used value today is 0x2000 and not 0x400. Rework the
Kconfig logic to use this more frequently used value as the default.
Cc: Andrew F. Davis <afd@ti.com>
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Alison Wang <alison.wang@nxp.com>
Cc: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Cc: Andes <uboot@andestech.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Bharat Gooty <bharat.gooty@broadcom.com>
Cc: David Lechner <david@lechnology.com>
Cc: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Eugeniy Paltsev <paltsev@synopsys.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Gerald Kerma <dreagle@doukki.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Holger Brunck <holger.brunck@hitachienergy.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Kristian Amlie <kristian.amlie@northern.tech>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Liviu Dudau <liviu.dudau@foss.arm.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Cc: Matthias Brugger <mbrugger@suse.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Cc: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Bosch <stefan_b@posteo.net>
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tony Dinh <mibodhi@gmail.com>
Cc: Trevor Woerner <twoerner@gmail.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: liuhao <liuhao@phytium.com.cn>
Cc: lixinde <lixinde@phytium.com.cn>
Cc: shuyiqi <shuyiqi@phytium.com.cn>
Cc: weichangzheng <weichangzheng@phytium.com.cn>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Kristian Amlie <kristian.amlie@northern.tech>
|
|
This converts the following to Kconfig:
CONFIG_SYS_MEM_TOP_HIDE
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Since this box is SystemReady compliant enable ISO_PARTITION which is
needed to start some installers (e.g Fedora). While at it enable EXT4
as well which is a common filesystem for targets
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
|
|
This commit adds the default configuration file and
relevant description for a MK808 board.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Move ROCKCHIP_STIMER_BASE to Kconfig.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add options to enable AHCI, SCSI and SATA.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-07-rc1-2
Documentation:
* Describe env command
UEFI
* simplify Unicode string functions
* clean up the usage of GUIDs for capsule updates
|
|
- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.
[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]
|
|
The current UEFI capsule updation code uses two GUID values, one for
FIT images, and one for raw images across platforms. This logic is
being changed to have GUID values per image, per platform. Change the
tests for the capsule update code to reflect this change. The GUID
values now used are the ones specific to the sandbox platform -- one
for the u-boot image, and another for the u-boot environment image.
Install the FMP instance for raw images on the sandbox variant for
testing the capsule update code. Install the FMP instance for the FIT
images on the sandbox64 and sandbox_flattree variant for testing
capsule update for FIT images. This is being done by splitting the
capsule update script for FIT and raw images.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
|
|
Increase the malloc pool on sandbox in order to avoid spurious errors
such as:
___________________ test_ut[ut_dm_dm_test_video_comp_bmp32] ____________________
test/py/tests/test_ut.py:43: in test_ut
assert output.endswith('Failures: 0')
E AssertionError: assert False
E + where False = <built-in method endswith of str object at 0x7f5de85efb20>('Failures: 0')
E + where <built-in method endswith of str object at 0x7f5de85efb20> = 'Test: dm_test_video_comp_bmp32: video.c\r\r\nSDL renderer does not exist\r\r\ntest/dm/video.c:86, compress_frame_buff..._test_video_comp_bmp32(): 2024 == compress_frame_buffer(uts, dev): Expected 0x7e8 (2024), got 0x1 (1)\r\r\nFailures: 2'.endswith
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Drop legacy #define CONFIG_DRIVER_DM9000 from board include/configs/
and enable the same in Kconfig configs/ .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20220413
i.MX patches for 2022.07
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/11710
|
|
The GW7903 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD socket with voltage select support
- Gateworks System Controller
- M.2 A-E Socket with USB2.0 and PCIe
- MiniPCIe Socket with PCIe, USB2.0, and SIM
- IMX8M FEC
- RS232/RS485/RS422 serial transceiver
- LIS2DE12 3-axis accelerometer
- front panel LED's
- off-board isolated digital I/O
- Wide range DC power input
- 802.3at PoE
- PMIC
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
|
|
The "mmc dev ${mmcdev}" command is done twice.
Remove one ocurrence to avoid the duplication.
Signed-off-by: Fabio Estevam <festevam@denx.de>
|
|
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enought space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
|
|
Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
1M of heap is more than internal ram making booting without SDRAM not
possible now it is 256k
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
|
|
rcar3_salvator-x u-boot.img is very close to the 0x100000 size limit.
Enable linked time optimization (LTO).
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Add support for Data Modul i.MX8M Mini eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR,
USB host and USB OTG.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Add redundand environment support as it is required
by SWUpdate.
While at it, also adjust the CONFIG_ENV_OFFSET to a more appropriate
larger offset as done on other i.MX8M defconfigs.
Signed-off-by: Fabio Estevam <festevam@denx.de>
|
|
Currently the eth0 MAC address is randomly assigned.
Retrieve the MAC address from EEPROM.
Signed-off-by: Fabio Estevam <festevam@denx.de>
|
|
Introduce BSH SystemMaster (SMM) S2 board family, which consists of:
iMX8MN SMM S2 and iMX8MN SMM S2 PRO boards.
Add support for iMX8MN BSH SMM S2 board:
- 256 MiB DDR3 RAM
- 512MiB Nand
- USBOTG1 peripheral - fastboot.
- 100Mbit Ethernet
Add support for iMX8MN BSH SMM S2 PRO board:
- 512 MiB DDR3 RAM
- 8 GiB eMMC
- USBOTG1 peripheral - fastboot.
- 100Mbit Ethernet
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
|
|
Enable CONFIG_DM_SERIAL, and `dm tree` could show:
serial 1 [ ] serial_mxc | |-- serial@30a80000
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Use the Micrel KSZ8xxx specific Ethernet PHY driver rather than the
generic one.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Enable driver model for serial.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
When TEE is present, the DRAM maybe split to two parts,
so enlarge CONFIG_NR_DRAM_BANKS
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Enable support for backlight/pwm-imx driver
Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
|
|
Conversion to DM_SERIAL is mandatory.
Select DM_SERIAL and add a imx6q-tbs2910-u-boot.dtsi file
that describes the nodes that require dm-pre-reloc, which allows
the DM model to configure the UART pinctrl early.
Remove the now unneeded board UART initialization.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Soeren Moch <smoch@web.de>
|
|
With DM_SERIAL selected, it is no longer needed board code to
initialize the UART.
Describe the nodes that require dm-pre-reloc, which allows
the DM model to configure the UART pinctrl early.
Remove the now unneeded board UART initialization.
Signed-off-by: Fabio Estevam <festevam@denx.de>
|
|
convert to DM_I2C for U-Boot while leaving SPL legacy I2C:
- Move I2C config from common to SPL
- Move PMIC config from common to SPL (no need to re-configure pmic)
- add DM_I2C support to eeprom/gsc functions shared by SPL and U-Boot
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
U-Boot complains that CONFIG_SERIAL is not converted to CONFIG_DM_SERIAL
and gives a deadline before possibly removing the board. Migrate to
DM_SERIAL to fulfill the request.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
|
|
Enable LTO on mamoj to reduce SPL and uboot size. Tested with gcc
gcc-11.1.0
U-Boot 2022.04-rc4-00051-g17fc5facd0 (Mar 23 2022 - 16:43:43 +0100)
CPU: Freescale i.MX6DL rev1.3 996 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 40C
Reset cause: POR
Model: BTicino i.MX6DL Mamoj board
DRAM: 512 MiB
Core: 29 devices, 12 uclasses, devicetree: separate
MMC: FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net:
Error: ethernet@2188000 address not set.
No ethernet found.
Tested-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
|
|
removed sec_init() call from board files.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
LS(1021/1012/1028/1043/1046/1088/2088), LX2160, LX2162
platforms are enabled with JR driver model.
removed sec_init() call from board files.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
|
|
Because we don't use SPL_DM on mx6sabresd and mx6sabreauto, so it is
unnecessary to have SPL DTB related configs and SPL_OF_CONTROL enabled.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
|
|
defconfig
If enable SPL_DM without SPL_OF_CONTROL,
build errors "undefined reference to fdt_get_resource",
is coming in function `caam_jr_probe'.
Added SPL_OF_CONTROL to remove the error.
Signed-off-by: Kshitiz Varshney <kshitiz.varshney@nxp.com>
|
|
When the RNG device is secured with OP-TEE, it is only accessible with
the HWRNG TA, the CONFIG_RNG_OPTEE is needed for STM32MP15 targets
with OP-TEE support.
The probe of this RNG driver fails when the TA is not available in OP-TEE
and the previous driver can be used, as CONFIG_RNG_STM32MP1 is activated
and when the associated node is activated in the device tree with:
&rng1 {
status = "okay";
};
When the RNG is used in OP-TEE, this node should be deactivated in
the Linux and U-Boot device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_FSL_QIXIS
CONFIG_QIXIS_I2C_ACCESS
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_DIMM_SLOTS_PER_CTLR
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This is a little tricky since SoCFPGA has code to determine this as
runtime. Introduce a guard variable for platforms to select if they
have a static value to use. Then for ARCH_SOCFPGA, call
cm_get_qspi_controller_clk_hz() and otherwise continue the previous
behavior.
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SH_SCIF_CLK_FREQ
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_CMDLINE_PS_SUPPORT
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_BOARD_SIZE_LIMIT
To do this, introduce CONFIG_HAS_BOARD_SIZE_LIMIT.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Up till now the CONFIG_POWER_TPS65217 has been defined in several header
files for am335x SoC.
This patch renames it to CONFIG_PMIC_TPS65217, which better reflects the
role of this IC circuit.
Moreover, new CONFIG_PMIC_TPS65217 has been introduced in Kconfig
to be used with boards, which both support DM_PMIC and DM_I2C.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Migrate all other platforms as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
