aboutsummaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2020-10-09arm: socfpga: Use DM watchdog timerChee Hong Ang
All SoCFPGA platforms (except Cyclone V) are now switching to CONFIG_WDT (driver model for watchdog timer drivers) from CONFIG_HW_WATCHDOG. Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com> Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
2020-10-09configs: socfpga: soc64: Avoid SPL enter infinite loop during exceptionChin Liang See
In current implementation, any exception would trigger a CPU reset. But a bad written SPL would cause infinite loop where the system will reload the same SPL instead of loading factory safe image. Hence this patch is to ensure any exception will cause a hang. At this moment, watchdog shall be triggered and Remote System Update mechanism shall load the next production image or factory safe image. Signed-off-by: Chin Liang See <chin.liang.see@intel.com> Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com> Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
2020-10-08qemu-arm64: Enable POSITION_INDEPENDENTAndre Przywara
Now that PIE works when U-Boot is started from ROM, let's enable CONFIG_POSITION_INDEPENDENT, which allows to load U-Boot also via ARM Trusted-Firmware's fip.bin to DRAM, without tweaking the configuration. To get a writable initial stack, we need to keep the fixed initial stack pointer, which points to DRAM in our case. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
2020-10-07mips: octeon: octeon_ebb7304_defconfig: Enable USB supportStefan Roese
This patch enables USB support with some helpful commands, like fs support. Signed-off-by: Stefan Roese <sr@denx.de>
2020-10-07mips: octeon: octeon_ebb7304: Add DDR4 supportStefan Roese
This patch adds the board specific configuration (struct) for the Octeon 3 EBB7304 EVK. This struct is ported from the 2013er Cavium / Marvell U-Boot repository. Also, the Octeon RAM driver is enabled in the board defconfig for its usage. Tested with one and two DIMMs on the EBB7304 EVK (8 & 16 GiB). Signed-off-by: Stefan Roese <sr@denx.de>
2020-10-06Merge tag 'efi-2021-01-rc1' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for efi-2021-01-rc1 The following bugs in the UEFI system are resolved: * illegal free in EFI_LOAD_FILE2_PROTOCOL implementation * incorrect documentation of EFI_LOAD_FILE2_PROTOCOL implementation * output of CRC32 as decimal instead hexadecimal in unit test * use EfiReservedMemoryType for no-map reserved memory * avoid unnecessary resets in UEFI unit tests * call EFI bootmgr even without having /EFI/boot
2020-10-06Merge tag 'u-boot-amlogic-20201005' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic - generate unique mac address from SoC serial on S400 board - Add USB support for GXL and AXG SoCs - Update Gadget code to use the new GXL and AXG USB glue driver - Add a VIM3 board support to add dynamic PCIe enable in OS DT - Fix AXG pinmux with requesting GPIOs - Add missing GPIOA_18 for AXG pinctrl - Add Amlogic PWM driver
2020-10-06efi_loader: QEMU CONFIG_EFI_GRUB_ARM32_WORKAROUND=nHeinrich Schuchardt
CONFIG_EFI_GRUB_ARM32 is only needed for architectures with caches that are not managed via CP15 (or for some outdated buggy versions of GRUB). It makes more sense to disable the setting per architecture than per defconfig. Move QEMU's CONFIG_EFI_GRUB_ARM32_WORKAROUND=n from defconfig to Kconfig. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-10-05configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-05Merge branch 'next'Tom Rini
Bring in the assorted changes that have been staged in the 'next' branch prior to release. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-05board: amlogic: vim3: add support for dynamic PCIe enableNeil Armstrong
The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between an USB3.0 Type A connector and a M.2 Key M slot. The PHY driving these differential lines is shared between the USB3.0 controller and the PCIe Controller, thus only a single controller can use it. This adds this dynamic switching right before booting Linux and the configuration steps in the boards documentation. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> [narmstrong: fixed warning by replacing min() by min_t()]
2020-10-05configs: vim3: use the vim3 board supportNeil Armstrong
Use the newly added VIM3 board support instead of the generic W400. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2020-10-05configs: s400: enable USBNeil Armstrong
Enable USB Host & Gadget on the Amlogic S400 board. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2020-10-05ARM: mach-meson: use new DWC3 glue for GXL & GXMNeil Armstrong
Use the new Amlogic GXL/GXM USB Glue instead of the set of USB3 PHY and Simple DWC3 wrapper. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2020-10-01Merge branch 'next' of git://git.denx.de/u-boot-sh into nextTom Rini
2020-10-01Merge branch '2020-09-30-assorted-network-improvements' into nextTom Rini
- Generic UDP framework - TFTP fixes - dwc_eth_qos, smc911x, smc911x and mscc phy fixes
2020-09-30sandbox: enable support of generic udp protocolPhilippe Reynes
This commit enable the support of the generic udp protocol. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-09-30firmware: smci: sandbox test for SCMI reset controllersEtienne Carriere
Add tests for SCMI reset controllers. A test device driver sandbox-scmi_devices.c is used to get reset resources, allowing further resets manipulation. Change sandbox-smci_agent to emulate 1 reset controller exposed through an agent. Add DM test scmi_resets to test this reset controller. Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org> Cc: Simon Glass <sjg@chromium.org> Cc: Peng Fan <peng.fan@nxp.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-09-30firmware: scmi: sandbox test for SCMI clocksEtienne Carriere
Add tests for SCMI clocks. A test device driver sandbox-scmi_devices.c is used to get clock resources, allowing further clock manipulation. Change sandbox-smci_agent to emulate 3 clocks exposed through 2 agents. Add DM test scmi_clocks to test these 3 clocks. Update DM test sandbox_scmi_agent with load/remove test sequences factorized by {load|remove}_sandbox_scmi_test_devices() helper functions. Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org> Cc: Simon Glass <sjg@chromium.org> Cc: Peng Fan <peng.fan@nxp.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-09-30firmware: add SCMI agent uclassEtienne Carriere
This change introduces SCMI agent uclass to interact with a firmware using the SCMI protocols [1]. SCMI agent uclass currently supports a single method to request processing of the SCMI message by an identified server. A SCMI message is made of a byte payload associated to a protocol ID and a message ID, all defined by the SCMI specification [1]. On return from process_msg() method, the caller gets the service response. SCMI agent uclass defines a post bind generic sequence for all devices. The sequence binds all the SCMI protocols listed in the FDT for that SCMI agent device. Currently none, but later change will introduce protocols. This change implements a simple sandbox device for the SCMI agent uclass. The sandbox nicely answers SCMI_NOT_SUPPORTED to SCMI messages. To prepare for further test support, the sandbox exposes a architecture function for test application to read the sandbox emulated devices state. Currently supports 2 SCMI agents, identified by an ID in the FDT device name. The simplistic DM test does nothing yet. SCMI agent uclass is designed for platforms that embed a SCMI server in a firmware hosted somewhere, for example in a companion co-processor or in the secure world of the executing processor. SCMI protocols allow an SCMI agent to discover and access external resources as clock, reset controllers and more. SCMI agent and server communicate following the SCMI specification [1]. This SCMI agent implementation complies with the DT bindings defined in the Linux kernel source tree regarding SCMI agent description since v5.8. Links: [1] https://developer.arm.com/architectures/system-architectures/software-standards/scmi Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org> Cc: Simon Glass <sjg@chromium.org> Cc: Peng Fan <peng.fan@nxp.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-09-26board: renesas: remove empty board_early_init_f functionBiju Das
Remove empty board_early_init_f function, since it is disabled in ebisu and condor board configs. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
2020-09-26arm: rmobile: Use imply for BOARD_EARLY_INIT_FBiju Das
Use "imply" instead of "select" for BOARD_EARLY_INIT_F config option, and then disable it on boards which don't need it. Updated grpeach_defconfig to disable CONFIG_BOARD_EARLY_INIT_F option for RZA1. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
2020-09-26ARM: rmobile: Enable dfu tftp on Gen3Marek Vasut
Enable the fitImage update options on RCar Gen3 boards. This permits easy update of multiple bootloader components. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2020-09-26ARM: rmobile: Enable RPC on Salvator-X, ULCB, EbisuMarek Vasut
Enable the RPC Hyperflash driver on R8A7795,R8A7796,R8A77965 Salvator-X,ULCB and R8A77990 Ebisu. Note that to make the HF accessible, mainline ATF is mandatory and must be built with RCAR_RPC_HYPERFLASH_LOCKED=0 . Note that this is intended for development and testing convenience only and must be disabled in deployment for platform security reasons. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2020-09-25Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini
- Bug fixes related to PCIe, pfe, xfi, gpio, reset, vid, env, and usb on layerscape products
2020-09-25Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 ↵Tom Rini
into next - Enhance the 'zboot' command to be more like 'bootm' with sub-commands - The last series of ACPI core changes for programmatic generation of ACPI tables - Add all required ACPI tables for ApolloLake and enable ACPIGEN on Chromebook Coral - A feature minor enhancements to the 'hob' command - Intel edison: Support for writing an xFSTK image via binman
2020-09-25x86: coral: Update config and device tree for ACPISimon Glass
Enable new features and provide require device-tree config so that U-Boot produces the correct ACPI tables on Coral. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-09-25x86: apl: Generate CPU tablesSimon Glass
Add ACPI generation to the APL CPU driver. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-09-25x86: acpi: Add a common routine to write WiFi infoSimon Glass
Intel WiFi chips can use a common routine to write the information needed by linux. Add an implementation of this. Enable it for coral. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-09-25x86: link: Allow more space for U-BootSimon Glass
The extra ACPI code increases U-Boot above it current size limit. Move the start earlier to provide space. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-09-24Merge tag 'xilinx-for-v2021.01' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next Xilinx changes for v2021.01 arm64: - Support for bigger U-Boot images compiled with PIE microblaze: - Extend support for LE/BE systems zynqmp: - Refactor silicon ID detection code with using firmware interface - Add support for saving variables based on bootmode zynqmp-r5: - Fix MPU mapping and defconfig setting. xilinx: - Minor driver changes: names alignment - Enable UBIFS - Minor DT and macros fixes - Fix boot with appended DT - Fix distro boot cmd: - pxe: Add fixing for platforms with manual relocation support clk: - fixed_rate: Add DM flag to support early boot on r5 fpga: - zynqmppl: Use only firmware interface and enable SPL build serial: - uartlite: Enable for ARM systems and support endians mmc: - zynq: Fix indentation net: - gem: Support for multiple phys - emac: Fix 64bit support and enable it for arm64 kconfig: - Setup default values for Xilinx platforms - Fix dependecies for Xilinx drivers - Source board Kconfig only when platform is enabled - Fix FPGA Kconfig entry with SPL - Change some defconfig values bindings: - Add binding doc for vsc8531
2020-09-24configs: powerpc: add usb (host) mass storage supportRan Wang
commit 0cfccb54014b ("configs: Resync with savedefconfig") removed CONFIG_USB_STORAGE from some powerpc platforms' defconfig files, whicih would block the use case of system loading rootfs from USB drives, add them back. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24configs: Remove P5040DS secure boot configsPriyanka Jain
Remove NXP powerpc P5040DS secure boot configs as they are no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24board/freescale: Remove P5020DS board supportPriyanka Jain
Remove NXP powerpc P5020DS board support as it is no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24powerpc:Remove P4080DS secure boot configsPriyanka Jain
Remove NXP powerpc P4080DS secure boot configs as they are no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24configs: Remove P3041DS secure boot configsPriyanka Jain
Remove NXP powerpc P3041DS secure boot configs as they are no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24board/freescale: Remove P1024RDB board supportPriyanka Jain
Remove NXP powerpc P1024RDB board support as it is no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24board/freescale: Remove P1021RDB board supportPriyanka Jain
Remove NXP powerpc P1021RDB board support as it is no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24board/freescale: Remove P1020MBG board supportPriyanka Jain
Remove NXP powerpc P1020MBG board support as it is no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24board/freescale: Remove P1020UTM board supportPriyanka Jain
Remove NXP powerpc P1020UTM board support as it is no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24board/freescale: Remove P1025RDB board supportPriyanka Jain
Remove NXP powerpc P1025RDB board support as it is no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24configs: Remove P1010RDB secure boot configsPriyanka Jain
Remove NXP powerpc P1010RDB secure boot configs as they are no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24board/freescale: Remove p1023rdb board supportPriyanka Jain
Remove NXP powerpc p1023rdb board support as it is no longer maintained. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24configs: P2020RDB: Enable DM_ETH configHou Zhiqiang
Enable the DM_ETH and DM_MDIO config. On P2020RDB, the eTSEC1 is connecting with a switch VSC7385, so also enable the fixed PHY support. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24configs: P1010RDB: Enable DM_ETH configHou Zhiqiang
Enable the DM_ETH and DM_MDIO config. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24configs: P1020RDB: Enable DM_ETH configHou Zhiqiang
Enable the DM_ETH and DM_MDIO config. On P1020RDB, the eTSEC1 is connecting with a switch VSC7385, so also enable the fixed PHY support. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24configs: enable DM_MDIO for LS1021A-TWR and LS1021A-TSNVladimir Oltean
The tsec driver now requires DM_MDIO when DM_ETH is enabled. To avoid build errors, enable DM_MDIO in these boards' configs before we actually add DM_MDIO support to tsec. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24configs: P1010RDB: Enable eSPI controller and SPI flash DM driverHou Zhiqiang
Enable the DM_SPI and DM_SPI_FLASH in P1010RDB defconfigs except SECBOOT defconfigs. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24configs: T4240RDB: Enable ESPI driverXiaowei Bao
Enable the DM ESPI driver in T4240RDB defconfig. Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24configs: T2080RDB: Enable ESPI driverXiaowei Bao
Enable the DM ESPI driver in T2080RDB defconfig. Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-13 06:05:25 +0000