aboutsummaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2018-03-19board: st: add generic board for STM32MP1 familyPatrick Delaunay
Add first support for STM32MP157C-ED1 board with "Basic" boot chain 1/ Boot Rom: load SPL with STM32 image header in SYSRAM 2/ SPL: power up and initialize the DDR and load U-Boot image from SDCARD in DDR 3/ U-Boot: search and load extlinux.conf in SDCARD (DISTRO activated) Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-03-19board: Add display to STM32F746 SoC discovery boardyannick fertre
Signed-off-by: yannick fertre <yannick.fertre@st.com>
2018-03-16Convert all of CONFIG_CONS_INDEX to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-16defconfig: k2l_hs_evm: Add k2l_hs_evm_defconfigMadan Srinivas
Adds a dedicated defconfig to build TI K2L secure devices and updates MAINTAINERS. k2l_hs_evm_defconfig is created from the k2l_evm_defconfig and removes support for SPL, as SPL is not supported on K2 HS devices. Corrects SYS_TEXT_BASE for HS devices. Also adds TI_SECURE_DEVICE and FIT_IMAGE_POST_PROCESS to include support for secure image creation and authentication Signed-off-by: Madan Srinivas <madans@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Andrew F. Davis <afd@ti.com>
2018-03-15Merge git://git.denx.de/u-boot-spiTom Rini
2018-03-14omap3_logic: Enable DM_SPIAdam Ford
With the introduction of ("Boards,Need,to,Switch,DM] spi: omap3_spi: Full dm conversion"), Driver Model for McSPI is now available on the omap3. This enables the config by default on omap3_logic boards. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-14Merge git://git.denx.de/u-boot-sunxiTom Rini
2018-03-14sunxi: move CONFIG_SYS_TEXT_BASE out of defconfigsAndre Przywara
Commit 278b90ce786f ("configs: Migrate CONFIG_SYS_TEXT_BASE") made CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence of moving the common definition shared by almost every sunxi board into 123 individual defconfig files. But the U-Boot start address for Allwinner boards is a platform decision which has been around for ages, so defining it in each *board* config file seems a bit over the top. Define the standard values (160MB into DRAM for most SoCs, with two SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from the individual defconfigs. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-13configs: am335x_boneblack: Enable fastboot flash capabilitySam Protsenko
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Acked-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-03-13configs: dra7xx_evm: Enable support for the HS200 mmc mode in the SPLJean-Jacques Hiblot
Beside enabling the support for HS200 in mmc core, enabling the HS200 support in the SPL requires multi-dtb support in the SPL because pinctrl and IOdelays vary across SOCs. Also we need to make sure that the pinctrl properties arenot removed from the dts by setting CONFIG_OF_SPL_REMOVE_PROPS to remove only clocks and interrupts properties. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-03-13ARM: omap3: evm: Sync with omap3_beagle configurationDerald D. Woods
This commit does the following for OMAP3 EVM: - Track omap3_beagle changes where possible - Remove CONFIG_SYS_MPUCLK and CONFIG_MTD which are not needed for the default board configuration to work. - Remove CONFIG_SPL_SYS_MALLOC_SIMPLE and CONFIG_SYS_MALLOC_F_LEN from default config. CONFIG_SYS_MALLOC_F_LEN=0x400 is set by configuration automatically. [allows board to boot with SERIAL_SEARCH_ALL=y] - Use updated NAND layout: device nand0 <omap2-nand.0>, # parts = 6 #: name size offset ------------------------------------------------- 0: spl 0x00080000(512k) 0x00000000 1: u-boot 0x001e0000(1920k) 0x00080000 2: u-boot-env 0x00020000(128k) 0x00260000 3: dtb 0x00020000(128k) 0x00280000 4: kernel 0x00600000(6m) 0x002a0000 5: rootfs 0x0f760000(-) 0x008a0000 ------------------------------------------------- Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2018-03-13ARM: omap3: beagle: Enable DM_SERIAL, update distro usage and NAND layoutDerald D. Woods
This commit does the following for BeagleBoard{-xM}: - Enable DM_SERIAL which also enables SPL_DM_SERIAL - Misc. config updates in support of DM_SERIAL - Use updated NAND layout (BeagleBoard): device nand0 <omap2-nand.0>, # parts = 6 #: name size offset ------------------------------------------------- 0: spl 0x00080000(512k) 0x00000000 1: u-boot 0x001e0000(1920k) 0x00080000 2: u-boot-env 0x00020000(128k) 0x00260000 3: dtb 0x00020000(128k) 0x00280000 4: kernel 0x00600000(6m) 0x002a0000 5: rootfs 0x0f760000(-) 0x008a0000 ------------------------------------------------- - Use MMC and UBIFS support from config_distro_bootcmd.h - Use LEGACY_MMC and NAND support defined in omap3_beagle.h [MMC(0:1)/extlinux/extlinux.conf] ---8<------------------------------------------------------------------- default omap3-beagle-mmc-fat label omap3-beagle-mmc-fat kernel /zImage fdt /omap3-beagle.dtb append console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait ---8<------------------------------------------------------------------- [LEGACY_MMC(0:2)/boot/extlinux/extlinux.conf] ---8<------------------------------------------------------------------- default omap3-beagle-mmc-ext4 label omap3-beagle-mmc-ext4 kernel /boot/zImage fdt /boot/omap3-beagle.dtb append console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait ---8<------------------------------------------------------------------- [UBIFS(ubi0:rootfs)/boot/extlinux/extlinux.conf] ---8<------------------------------------------------------------------- default omap3-beagle-nand-ubifs label omap3-beagle-nand-ubifs kernel /boot/zImage fdt /boot/omap3-beagle.dtb append console=ttyO2,115200n8 root=ubi0:rootfs rw ubi.mtd=rootfs rootfstype=ubifs rootwait ---8<------------------------------------------------------------------- The board's 'bootcmd' can also be overridden with: CONFIG_BOOTCOMMAND="run findfdt; run mmcboot" CONFIG_BOOTCOMMAND="run findfdt; run nandboot" CONFIG_BOOTCOMMAND="run findfdt; run ramboot" or CONFIG_BOOTCOMMAND="run findfdt; run somethingelse" The use of 'run findfdt' is required. Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2018-03-13configs: stm32: Enable DOS_PARTITION for STM32F4/F7 boardsPatrice Chotard
Enable DOS_PARTITION for boards STM32F429-eval, STM32F469-disco and STM32F746-disco. This allows to read FAT partition on mmc. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-03-13rockchip: rk3288-vyasa: defconfig: Enable gmac supportJagan Teki
Enable gmac support for rk3288-vyasa board. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-03-13sunxi: Add A20-SOM204-EVB-eMMC boardStefan Mavrodiev
A20-SOM204 board has option with onboard 16GB eMMC. The chip is wired to MMC2 slot. This patch adds defconfig and dts files for this board. The dts is same with mainline kernel. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-13sunxi: Add A20-SOM204-EVB boardStefan Mavrodiev
This is new System-On-Module platform with universal dimm socket for easy insertation. The EVB board is designed to be universal with future modules. Base features of A20-SOM204 board includes: * 1GB DDR3 RAM * AXP209 PMU * KSZ9031 Gigabit PHY * AT24C16 EEPROM * Status LED * LCD connector * GPIO connector There will be variants with the following options: * Second LAN8710A Megabit PHY * 16MB SPI Flash memory * eMMC card * ATECC508 crypto device The EVB board has: * Debug UART * MicroSD card connector * USB-OTG connector * Two USB host * RTL8723BS WiFi/BT combo * IrDA transceiver/receiver * HDMI connector * VGA connector * Megabit ethernet transceiver * Gigabit ethernet transceiver * SATA connector * CAN driver * CSI camera * MIC and HP connectors * PCIe x4 connector * USB3 connector * Two UEXT connectors * Two user LEDs Some of the features are multiplexed and cannot be used the same time: CAN and Megabit PHY. Others are not usable with A20 SoC: PCIe and USB3. This patch adds defconfig and dts files for this board. The dts is same with mainline kernel, except some nodes are removed to make file compatible with existing dtsi file. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-13Move CONFIG_PHY_ADDR to KconfigStefan Mavrodiev
CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-13sunxi: Pine64: temporarily remove extra Pine64 non-plus DTAndre Przywara
With the merge of the new u-boot.itb size check now the build for pine64_plus_defconfig breaks, as this file gets too large: ============= u-boot.itb exceeds file size limit: limit: 516096 bytes actual: 521852 bytes excess: 5756 bytes make: *** [u-boot.itb] Error 1 ============= One easily fixable reason is that we actually have two .dtbs in our FIT image, one for the regular Pine64+ board, and one for the non-plus version. The only difference U-Boot cares about is the 100Mbit Ethernet PHY used on the non-plus version, however Ethernet isn't enabled in the non-plus DT anyway. So we could avoid the non-plus special handling, and remove that extra .dtb from the FIT image, which saves a few KBs and brings us back below the limit. The Pine64 would boot with a Pine64+ .dtb, and would fail to enable Ethernet. Given that it didn't work in the first place, this is not a regression. Once we switch to a non-MMC environment, we can bring this back, then with a proper .dtb and hopefully working Ethernet. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-09configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-05Merge git://git.denx.de/u-boot-shTom Rini
2018-03-05MPC8315ERDB: Enable DHCP supportEd Bartosh
Enable DHCP support for this board. Signed-off-by: Ed Bartosh <ed.bartosh@linux.intel.com> Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-05spl: Kconfig: Rename SPL_USBETH_SUPPORT to SPL_USB_ETHER to match with the ↵Faiz Abbas
U-boot CONFIG Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER. This enables users to block text using CONFIG_IS_ENABLED() instead of resorting to #if ladders with SPL and non-SPL cases. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2018-03-05ARM: rmobile: Add R8A77965 Salvator-XS board supportMarek Vasut
Add R8A77965 M3N Salvator-XS development kit support. This kit is similar to the other Salvator-X(S) ones, except is has M3N SoC on it. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-03-01Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2018-03-01mmc: Added Kconfig support for CONFIG_ZYNQ_SDHCI_MIN_FREQVipul Kumar
This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MIN_FREQ and enabled it in respective defconfig. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-01mmc: Added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQVipul Kumar
This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ and enabled it in respective defconfig. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-01microblaze: Added Kconfig support for CONFIG_XILINX_GPIOVipul Kumar
This patch added Kconfig support for CONFIG_XILINX_GPIO and enabled it in respective defconfig. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-01i2c: Added kconfig support for CONFIG_ZYNQ_I2C0 and CONFIG_ZYNQ_I2C1Vipul Kumar
This patch added Kconfig support for CONFIG_ZYNQ_I2C0 and CONFIG_ZYNQ_I2C1 and enabled it in respective defconfig. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-01i2c: Added Kconfig support for CONFIG_ZYNQ_GEM_I2C_MAC_OFFSETVipul Kumar
This patch added Kconfig support for CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET and enabled it in respective defconfig. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-01i2c: Enabled CONFIG_SYS_I2C_ZYNQ in the respective defconfigVipul Kumar
This patch enabled CONFIG_SYS_I2C_ZYNQ in the respective defconfig. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-02-28arm: zynq: fpga: Added Kconfig support for CONFIG_FPGA_ZYNQPLVipul Kumar
This patch added Kconfig support for CONFIG_FPGA_ZYNQPL and migrates the values over to the defconfigs. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
2018-02-28fpga: Added Kconfig support for FPGA_SPARTAN3Vipul Kumar
This patch added Kconfig support for FPGA_SPARTAN3 and migrates the values over to the defconfigs. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
2018-02-27Kconfig: cmd: Make networking command dependent on NETMichal Simek
Enable networking command only when NET is enabled. And remove selecting NET for CMD_NET Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-27arm: socfpga: cyclone5: Enable Macronix flash supportChin Liang See
Enable Macronix flash support for Cyclone5 SoC Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
2018-02-26ARM: socfpga: Add new CycloneV SoC Devboards DBM-SoC1 boardMarek Vasut
Add support for a new boards from devboards.de , the DBM-SoC1 . This board has one ethernet port, one USB OTG port and USB UART. Signed-off-by: Marek Vasut <marex@denx.de>
2018-02-25Merge git://git.denx.de/u-boot-rockchipTom Rini
2018-02-25Merge git://git.denx.de/u-boot-imxTom Rini
2018-02-25bootcount: Migrate CONFIG_SYS_BOOTCOUNT_ADDRTom Rini
Migrate the users of CONFIG_SYS_BOOTCOUNT_ADDR to Kconfig. We can provide a default for BOOTCOUNT_AM33XX as that's a specific part of the RTC in use. We can also provide a default for ARCH_LS1043A and ARCH_LS1021A as they had been previously calculated and their symbols are in Kconfig. In the case of other QE-enabled platforms, they are not so we must update the relevant defconfig files. The previous default only applied in some cases, even on a specific SoC family. Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-24rockchip: rk3288: Fix wrong TPL_TEXT_BASEJagan Teki
TPL offset 0xff704004 is unaligned address which is adding nearest 8-bytes for next instruction, So 0xff704004 is adding 0x20 for proper alignment which is causing the next instruction data 0xefffffff is moved. Hexdump with overlaped bytes: ----------------------------- 0000000 0000 0000 0000 0000 0000 0000 0000 0000 0000010 0000 0000 0000 0000 0000 0000 ffff eaff So, Fix the TEXT_BASE for proper aligned address 0xff704000 Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-02-24Convert CONFIG_BOOTCOUNT_EXT to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_BOOTCOUNT_EXT Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-02-24Convert CONFIG_BOOTCOUNT_I2C to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_BOOTCOUNT_I2C Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2018-02-24Convert CONFIG_BOOTCOUNT_RAM to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_BOOTCOUNT_RAM Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2018-02-24Convert CONFIG_BOOTCOUNT_ENV to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_BOOTCOUNT_ENV Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2018-02-24Merge CONFIG_BOOTCOUNT and CONFIG_BOOTCOUNT_LIMITAlex Kiernan
CONFIG_BOOTCOUNT was only used in mx53ppd, merge it with CONFIG_BOOTCOUNT_LIMIT Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Ian Ray <ian.ray@ge.com>
2018-02-23Convert CONFIG_BOOTP_BOOTPATH et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-23omap3_logic: Fix Environmental locationAdam Ford
For the omap3_logic boards, the environment is always in NAND. This removes the ENV_IS_IN_FAT flag to eliminate the extra chatter. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-02-23configs: am335x_evm_usbspl: Add CONFIG_SPL_NET_VCI_STRINGFaiz Abbas
Add CONFIG_SPL_NET_VCI_STRING to enable USB-Ethernet boot mode support. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-02-23defconfig: k2x_hs_evm: Re-enable TI_SECURE_DEVICE in HS K2x partsAndrew F. Davis
These got removed in config re-syncs due to a Kconfig bug. Add these back here. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-02-23configs: Re-sync with CONFIG_DISTRO_DEFAULTSTom Rini
A number of platforms include config_distro_defaults.h but do not enable CONFIG_DISTRO_DEFAULTS. As they plainly intended to, set that flag and re-sync config files. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-22imx6q: engicam: Use SPL_LOAD_FIT for MMC boardsJagan Teki
Currently SPL_LOAD_FIT is unable to boot from nand on i.MX6QDL platform, so enable only for MMC boards. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-09-21 19:59:32 +0000