| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
ADS5121 Rev 3 board is now the default config
config targets are now
ads5121_config
Rev 3 board with
PCI
M41T62 on board RTC
512MB DRAM
ads5121_rev2_config
Rev 2 board with
No PCI
256MB DRAM
Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: John Rigby <jrigby@freescale.com>
|
|
Consolidate ADS5121 IO Pin configuration to one file
board/ads5121/iopin.c.
Remove pin config from cpu/mpc512x/fec.c
Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: John Rigby <jrigby@freescale.com>
|
|
Currently, END_OF_RAM is used by the trap code to determine if
we should attempt to access the stack pointer or not. However,
on systems with a lot of RAM, only a subset of the RAM is
guaranteed to be mapped in and accessible. Change END_OF_RAM
to use get_effective_memsize() instead of using the raw ram
size out of the bd.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).
Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Adds PCI support for MPC5121
Tested with drivers/net/rtl8139.c
Support is conditional since PCI on old silicon does not work.
ads5121_PCI_config turns on PCI
In this version, condition compilation of PCI code has been moved
from ifdef in board/ads5121/pci.c to board/ads5121/Makefile as
suggested by Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: John Rigby <jrigby@freescale.com>
|
|
R29 was an unlucky choice as with recent toolchains (gcc-4.2.x) gcc
will refuse to use load/store multiple insns; instead, it issues a
list of simple load/store instructions upon function entry and exit,
resulting in bigger code size, which in turn makes the build for a
few boards fail.
Use r2 instead.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
|
|
Changes to match 5121 device tree going mainline in 2.6.25.
Change OF_SOC from "soc5121" to plain "soc".
Remove unneeded "ref-frequency" fixups.
Remove "address" enetaddr fixup.
Add bus-frequency fixup for old OF_SOC so old
kernels with old device trees will work with new
u-boot with 66MHz IPS clock
Signed-off-by: John Rigby <jrigby@freescale.com>
|
|
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
|
|
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
|
|
This reverts commit 8d17979d0359492a822a0a409d26e3a3549b4cd4.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
- convert frame size settings to be derived from a single base
- set frame size to the recommended default value
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
|
|
When frame larger than local RX buffer is received, it is split and handled
by two buffer descriptors. Prior to this patch the FEC driver discarded
contents of a buffer descriptor without the 'LAST' bit set, so the first
part of the frame was lost in case of larger frames. This fix allows to
safely combine the two pieces into the whole frame.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
|
|
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
|
|
Also update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
The following MPC5121e subsystems are supported:
- low-level CPU init
- NOR Boot Flash (common CFI driver)
- DDR SDRAM
- FEC
- I2C
- Watchdog
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
Signed-off-by: Jan Wrobel <wrr@semihalf.com>
|
