u-boot.git - U-Boot bootloader

Age	Commit message (Collapse)	Author
2014-08-20	powerpc/t4qds: Move doc/README.t4240qds under board/freescale/t4qds	York Sun
	Board specific README file should be moved to board folder. Signed-off-by: York Sun <yorksun@freescale.com>
2014-08-20	powerpc/T4240QDS/eth: some fix for XFI	Shaohui Xie
	XFI is supported on T4QDS-XFI board, which removed slot3, and four LANEs of serdes2 are routed to a SFP+ cages, which to house fiber cable or direct attach cable(copper), the copper cable is used to emulate the 10GBASE-KR scenario. So, for XFI usage, there are two scenarios, one will use fiber cable, another will use copper cable. For fiber cable, there is NO PHY, while for copper cable, we need to use internal PHY which exist in Serdes to do auto-negotiation and link training, which implemented in kernel. We use hwconfig to define cable type for XFI, and fixup dtb based on the cable type. For copper cable, set below env in hwconfig: fsl_10gkr_copper:<10g_mac_name> the <10g_mac_name> can be fm1_10g1, fm1_10g2, fm2_10g1, fm2_10g2. The four <10g_mac_name>s do not have to be coexist in hwconfig. For XFI ports, if a given 10G port will use the copper cable for 10GBASE-KR, set the <10g_mac_name> of the port in hwconfig, otherwise, fiber cable will be assumed to be used for the port. For ex. if four XFI ports will both use copper cable, the hwconfig should contain: fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm2_10g1,fm2_10g2 For fiber cable: 1. give PHY address to a XFI port, otherwise, the XFI ports will not be available in U-boot, there is no PHY physically for XFI when using fiber cable, this is just to make U-boot happy and we can use the XFI ports in U-boot. 2. fixup dtb to use fixed-link in case of fiber cable which has no PHY. Kernel requests that a MAC must have a PHY or fixed-link. When using XFI protocol, the MAC 9/10 on FM1 should init as 10G interface. Change serdes 2 protocol 56 to 55 which has same feature as 56 since 56 is not valid any longer. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22	powerpc/T4QDS: add two stage boot of nand/sd	Shaohui Xie
	Add support of 2 stage NAND/SD boot loader using SPL framework. PBL initialise the internal SRAM and copy SPL, this further initialise DDR using SPD and environment and copy u-boot from NAND/SD to DDR, finally SPL transfer control to u-boot. NOR uses CS1 instead of CS2 when NAND boot, fix it. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2013-05-24	board/t4240qds, b4860qds: LAW/TLB for DCSR set to size 32M	Stephen George
	Debug trace buffers are memory mapped in DCSR space beyond 4M. Signed-off-by: Stephen George <stephen.george@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24	powerpc/t4240qds: Add VDD override	York Sun
	Allow VDD voltage overriding with a command. This is an add-on feasture of VID. To override VDD, use command vdd_override with the value of voltage in mV, for example vdd_override <voltage in mV, eg. 1050> The above example will set the VDD to 1.050 volt. Any wrong value out of range of 0.8188 to 1.2125 volt or invalid string is ignored. In addition to the command, if overriding VDD is needed earlier in booting process, save an variable and reboot: setenv t4240qds_vdd_mv <voltage in mV> saveenv Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22	powerpc/t4qds: Add T4QDS board	York Sun
	The T4240QDS is a high-performance computing evaluation, development and test platform supporting the T4240 QorIQ Power Architecture™ processor. SERDES Connections 32 lanes grouped into four 8-lane banks Two “front side” banks dedicated to Ethernet Two “back side” banks dedicated to other protocols DDR Controllers Three independant 64-bit DDR3 controllers Supports rates up to 2133 MHz data-rate Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller QIXIS System Logic FPGA Each DDR controller has two DIMM slots. The first slot of each controller has up to 4 chip selects to support single-, dual- and quad-rank DIMMs. The second slot has only 2 chip selects to support single- and dual-rank DIMMs. At any given time, up to total 4 chip selects can be used. Detail information can be found in doc/README.t4qds Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>