| Age | Commit message (Collapse) | Author |
|---|
|
This driver initializes PIC32 DDR2 SDRAM controller and internal DDR2 Phy module.
DDR2 controller operates in half-rate mode (upto 533MHZ frequency).
Signed-off-by: Paul Thacker <paul.thacker@microchip.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
A Platform Controller Hub is an Intel concept - it is like the peripherals
on an SoC and is often in a separate chip from the CPU. The chip is typically
found on the first PCI bus and integrates multiple devices.
We have a very simple uclass to support PCHs. Add a few operations, such as
setting up the devices on the PCH and finding the SPI controller base
address. Also move it into drivers/pch/ since we will be adding a few PCH
drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Until now, the SoC selection for the ARCH_MVEBU platforms has been done
in the config header. Using CONFIG_ARMADA_XP in a non-clear way. As
it needed to get selected for AXP and A38x based boards. This patch
now changes this to move the SoC selection to Kconfig. And also
uses CONFIG_ARCH_MVEBU as a common define for both AXP and A38x.
This makes things a bit clearer - especially for new board additions.
Additionally the defines CONFIG_SYS_MVEBU_DDR_AXP and
CONFIG_SYS_MVEBU_DDR_A38X are replaced with the already available
CONFIG_ARMADA_38X and CONFIG_ARMADA_XP.
And CONFIG_DDR3 is removed, as its not referenced anywhere.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
|
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This commit adds:
- new uclass id: UCLASS_ADC
- new uclass driver: drivers/adc/adc-uclass.c
The new uclass's API allows for ADC operation on:
* single-channel with channel selection by a number
* multti-channel with channel selection by bit mask
ADC uclass's functions:
* single-channel:
- adc_start_channel() - start channel conversion
- adc_channel_data() - get conversion data
- adc_channel_single_shot() - start/get conversion data
* multi-channel:
- adc_start_channels() - start selected channels conversion
- adc_channels_data() - get conversion data
- adc_channels_single_shot() - start/get conversion data for channels
selected by bit mask
* general:
- adc_stop() - stop the conversion
- adc_vdd_value() - positive reference Voltage value with polarity [uV]
- adc_vss_value() - negative reference Voltage value with polarity [uV]
- adc_data_mask() - conversion data bit mask
The device tree can provide below constraints/properties:
- vdd-polarity-negative: if true: Vdd = vdd-microvolts * (-1)
- vss-polarity-negative: if true: Vss = vss-microvolts * (-1)
- vdd-supply: phandle to Vdd regulator's node
- vss-supply: phandle to Vss regulator's node
And optional, checked only if the above corresponding, doesn't exist:
- vdd-microvolts: positive reference Voltage [uV]
- vss-microvolts: negative reference Voltage [uV]
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Implement a Timer uclass to work with lib/time.c.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Many System on Chip(SoC) solutions are complex with multiple processors
on the same die dedicated to either general purpose of specialized
functions. Many examples do exist in today's SoCs from various vendors.
Typical examples are micro controllers such as an ARM M3/M0 doing a
offload of specific function such as event integration or power
management or controlling camera etc.
Traditionally, the responsibility of loading up such a processor with a
firmware and communication has been with a High Level Operating
System(HLOS) such as Linux. However, there exists classes of products
where Linux would need to expect services from such a processor or the
delay of Linux and operating system being able to load up such a
firmware is unacceptable.
To address these needs, we need some minimal capability to load such a
system and ensure it is started prior to an Operating System(Linux or
any other) is started up.
NOTE: This is NOT meant to be a solve-all solution, instead, it tries to
address certain class of SoCs and products that need such a solution.
A very simple model is introduced here as part of the initial support
that supports microcontrollers with internal memory (no MMU, no
execution from external memory, or specific image format needs). This
basic framework can then (hopefully) be extensible to other complex SoC
processor support as need be.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
This creates a new framework for handling of pin control devices,
i.e. devices that control different aspects of package pins.
This uclass handles pinmuxing and pin configuration; pinmuxing
controls switching among silicon blocks that share certain physical
pins, pin configuration handles electronic properties such as pin-
biasing, load capacitance etc.
This framework can support the same device tree bindings, but if you
do not need full interface support, you can disable some features to
reduce memory foot print. Typically around 1.5KB is necessary to
include full-featured uclass support on ARM board (CONFIG_PINCTRL +
CONFIG_PINCTRL_FULL + CONFIG_PINCTRL_GENERIC + CONFIG_PINCTRL_PINMUX),
for example.
We are often limited on code size for SPL. Besides, we still have
many boards that do not support device tree configuration. The full
pinctrl, which requires OF_CONTROL, does not make sense for those
boards. So, this framework also has a Do-It-Yourself (let's say
simple pinctrl) interface. With CONFIG_PINCTRL_FULL disabled, the
uclass itself provides no systematic mechanism for identifying the
peripheral device, applying pinctrl settings, etc. They must be
done in each low-level driver. In return, you can save much memory
footprint and it might be useful especially for SPL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Just preparing for upcoming cleaning.
The board-specific linker script board/vpac270/u-boot-spl.lds
has been touched to avoid build error. It does not change the
size of spl/u-boot-spl.bin for this board, so it should be OK.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Clocks are an important feature of platforms and have become increasing
complex with time. Most modern SoCs have multiple PLLs and dozens of clock
dividers which distribute clocks to on-chip peripherals.
Some SoC implementations have a clock API which is private to that SoC family,
e.g. Tegra and Exynos. This is useful but it would be better to have a
common API that can be understood and used throughout U-Boot.
Add a simple clock API as a starting point. It supports querying and setting
the rate of a clock. Each clock is a device. To reduce memory and processing
overhead the concept of peripheral clocks is provided. These do not need to
be explicit devices - it is possible to write a driver that can adjust the
I2C clock (for example) without an explicit I2C clock device. This can
dramatically reduce the number of devices (and associated overhead) in a
complex SoC.
Clocks are referenced by a number, and it is expected that SoCs will define
that numbering themselves via an enum.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add support for a driver which sets up DRAM and can return information about
the amount of RAM available. This is a first step towards moving RAM init
to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add a simple uclass for LEDs, so that these can be controlled by the device
tree and activated when needed. LEDs are referred to by their label.
This implementation requires a driver for each type of LED (e.g GPIO, I2C).
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
It is useful to be able to keep track of the available CPUs in a multi-CPU
system. This uclass is mostly intended for use with SMP systems.
The uclass provides methods for getting basic information about each CPU.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
|
|
Add a new thermal uclass for thermal sensor and implement the imx
thermal driver basing on this uclass.
Signed-off-by: Ye.Li <B37916@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
ls1021 is arm-core and support qe which is u-qe.
add u-qe init for arm board.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
[York Sun: Fix compiling error caused by u_qe_init()]
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This patch split the Keystone II SGMII SerDes related code from
Ethernet driver and create a separate SGMII SerDes driver.
The SerDes driver can be used by others keystone subsystems
like PCI, sRIO, so move it to driver/soc/keystone directory.
Add soc specific drivers directory like in the Linux kernel.
It is going to be used by keysotone soc specific drivers.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
[1] Move driver/core/, driver/input/ and drivers/input/ entries
from the top Makefile to drivers/Makefile
[2] Remove the conditional by CONFIG_DM in drivers/core/Makefile
because the whole drivers/core directory is already selected
by CONFIG_DM in the upper level
[3] Likewise for CONFIG_DM_DEMO in drivers/demo/Makefile
[4] Simplify common/Makefile - both CONFIG_DDR_SPD and
CONFIG_SPD_EEPROM are boolean macros so they can directly
select objects
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
add basic support for the pwm modul found on imx6.
Pieces of this code are based on linux code from drivers/pwm/pwm-imx.c
Commit "cd3de83f1476 Linux 3.16-rc4"
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
|
|
Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF
definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
- Descend into drivers/fpga/ only when CONFIG_FPGA=y
- Descend into drivers/bios_emulator only when CONFIG_BIOSEMU=y
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
This commit moves some drivers subdirectory entry
from the toplevel Makefile to drivers/Makefile
using Kbuild descending feature.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Conflicts:
drivers/Makefile
|
|
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This change is in preparation for condtitionial compile support in the
build system. By spliting them all into seperate lines now, subsequent
patches that change 'COBJS-y += ' into 'COBJS-$(CONFIG_<blah>) += ' will
be less invasive and easier to review
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
