| Age | Commit message (Collapse) | Author |
|---|
|
- add additional function erratum_a009942_check_cpo to check if the
board needs tuning CPO calibration for optimal setting.
- move ERRATUM_A009942(with revision to check cpo_sample option) from
fsl_ddr_gen4.c to ctrl_regs.c for reuse on all DDR4/DDR3 parts.
- move ERRATUM_A008378 from fsl_ddr_gen4.c to ctrl_regs.c
- remove obsolete ERRATUM_A004934 which is replaced with ERRATUM_A009942.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
[YS: Replaced CONFIG_QEMU_E500 with CONFIG_ARCH_QEMU_E500]
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Fix following warning in case multiple erratum macro was not defined.
warning: unused variable 'tmp'
warning: unused variable 'ddr_freq'
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Replace CONFIG_MPC8555 with ARCH_MPC8555 in Kconfig and clean up existing
macros.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Replace CONFIG_MPC8541 with ARCH_MPC8541 in Kconfig and clean up existing
macros.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
To enable configuration of sdr.ctrlcfg.extratime1 register which enable
extra clocks for read to write command timing. This is critical to
ensure successful LPDDR2 interface
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Fix various misspellings of:
* deprecated
* partition
* preceding,preceded
* preparation
* its versus it's
* export
* existing
* scenario
* redundant
* remaining
* value
* architecture
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
trini: Drop local memset() from
examples/standalone/mem_to_mem_idma2intr.c
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Instead of using multiple macros, a data structure is used to pass
board-specific parameters to MMDC DDR driver.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Remove unneeded variables and assignments.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
When CONFIG_SYS_FSL_ERRATUM_A009801 is defined but
CONFIG_SYS_FSL_ERRATUM_A008511 not defined, there is compile error
that temp32 undeclared, this patch fixes it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
This general MMDC driver adds basic support for Freescale MMDC
(Multi Mode DDR Controller). Currently MMDC is integrated on ARMv8
LS1012A SoC for DDR3L, there will be a update to this driver to
support more flexible configuration if new features (DDR4, multiple
controllers/chip selections, etc) are implimented in future.
Meantime, reuse common MMDC driver for LS1012ARDB/LS1012AQDS/
LS1012AFRDM.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
DDR controller 5.2.1 has this erratum A008511 partially fixed.
The workaround needs to be adjusted to take advantage of Vref
training. This patch enables the training and force output
enable to be off.
Erratum A009803 requires the controller to be idel before enabling
address parity. It was combined with workaround for A008511. With
new A008511 flow, this flow needs to be changed to enabling
data init (D_INIT) after the address parity is enabled.
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
|
|
32 more debug registers are added for newer DDR controllers.
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
|
|
Commit 5605dc6 tried to fix wr_lat bit in timing_cfg_2, but the
change was wrong. wr_lat has 5 bits with MSB at [13] and lower
4 bits at [9:12], in big-endian convention.
Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Thomas Schaefer <Thomas.Schaefer@kontron.com>
|
|
Fix a number of typos, including:
* "compatble" -> "compatible"
* "eanbeld" -> "enabled"
* "envrionment" -> "environment"
* "FTD" -> "FDT" (for "flattened device tree")
* "ommitted" -> "omitted"
* "overriden" -> "overridden"
* "partiton" -> "partition"
* "propogate" -> "propagate"
* "resourse" -> "resource"
* "rest in piece" -> "rest in peace"
* "suport" -> "support"
* "varible" -> "variable"
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
|
|
Add condition of checking the enabled of address parity
for erratum A-009803, if parity is not enabled, the
workaround of erratum A-009803 should not be applied.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
If ECC is not enabled, data init can be disabled to speed up booting.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Commit 34e026f9 added one extra bit to wr_lat for timing_cfg_2, but
with wrong bit position. It is bit 13 in big-endian, or left shift
18 from LSB. This error hasn't had any impact because we don't have
fast enough DDR4 using the extra bit so far.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
The clk_adjust is of SDRAM_CLK_CNTL[5:8] 4-bits on MPC85xx and P-series,
but is of SDRAM_CLK_CNTL[5:9] 5-bits on T-series and LS-series SoCs.
We should update it to adapt the case that clk_adjust is odd data.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
|
|
For reason unknown, recently, the DDR init code writers are really fond
of hiding some small floating point operating deep in their creations.
This patch removes one from the Marvell A38x code.
Instead of returning size of chip as float from ddr3_get_device_size()
in GiB units, return it as int in MiB units. Since this would interfere
with the huge switch code in ddr3_calc_mem_cs_size(), rework the code
to match the change.
Before this patch, the cs_mem_size variable could have these values:
( { 16, 32 } x { 8, 16 } x { 0.01, 0.5, 1, 2, 4, 8 } ) / 8 =
{ 0.000000, 0.001250, 0.002500, 0.005000, 0.062500, 0.125000,
0.250000, 0.500000, 1.000000, 2.000000, 4.000000, }
The switch code checked for a subset of the resulting RAM sizes, which
is in range 128 MiB ... 2048 MiB.
With this patch, the cs_mem_size variable can have these values:
( { 16, 32 } x { 8, 16 } x { 0, 512, 1024, 2048, 4096, 8192 } ) / 8 =
{ 0, 64, 128, 256, 512, 1024, 2048, 4096 }
To retain previous behavior, filter out 0 MiB (invalid size), 64 MiB
and 4096 MiB options.
Removing the floating point stuff also saves 1.5k from text segment:
clearfog : spl/u-boot-spl:all -1592 spl/u-boot-spl:text -1592
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
During DDR-2133 operation, the transmit data eye margins determined
during the memory controller initialization may be sub-optimal, set
DEBUG_29[12] and DEBUG_29[13:16] = 4'b0100 before MEM_EN is set.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
The initial training for the DDRC may provide results that are not
optimized. The workaround provides better read timing margins.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Per the latest erratum document, update step 4 and step 8, only
DEBUG_29[21] is changed, all other bits should not be changed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The code uses a lot of signed numbers, which ended up in variables
of unsigned type, which resulted in all sorts of underflows. This
in turn caused incorrect calibration on certain boards. Moreover,
repair the readout of the DQ delay, which was being pulled from
wrong register.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
Just staticize global variables in sequencer, since there is no
point in having these symbols available outside of the DDR code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
Originally, the DLEVEL selects the debug level within the sequencer code,
but only displays the messages on that particular debug level. Tweak the
handling such that for particular debug level, debug messages on that
level and lower are displayed. This allows better regulation of debug
message verbosity.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
This one last set of delay configuration registers was not properly
zeroed out originally, fix it and zero them out.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
There is no point in resetting the ODT setting if the write test
failed, since the code will always retry the calibration and thus
reconfigure the ODT anyway OR the code will fail calibration and
halt.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
Every invocation of the scc_mgr_set_dqs_en_delay_all_ranks() is
followed by SCC manager update. Moreover, only this function
triggers the SCC manager update internally. Thus, remove the
internal invocation to avoid triggering the update twice.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
The hi address bitfield in the protection rule must be set to
the last address in the region which the rule represents. The
behavior is now in-line with code generated by Quartus 15.1 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
The code should be setting registers to zero, not one register to value.
Swap the order of arguments to correct the behavior. The behavior is now
in-line with code generated by Quartus 15.1 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
In the most unlikely case the DQS tracking was to be disabled,
make sure we do not errornously re-enable it. Note that DQS
tracking is enabled on all systems observed thus far.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
The bit 22 is in fact DQS tracking enable bit (dqstrken) and there
is a macro for this bit already, so use it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
|
|
Minor change: chosen is written with one "o".
No code change here, only comment & printf.
Signed-off-by: Alexander Merkle <alexander.merkle@lauterbach.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Armada 38x has a maximum of two cores. Probably copy/paste
bug from Armada XP.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
During initial DDR training, false parity errors may be detected.
This patch adds workaround to fix the erratum.
Tested on LS2085QDS and LS2080RDB.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Add support of address parity for DDR4 UDIMM or discrete memory.
It requires to configurate corresponding MR5[2:0] and
TIMING_CFG_7[PAR_LAT]. Parity can be turned on by hwconfig,
e.g. hwconfig=fsl_ddr:parity=on.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This driver initializes PIC32 DDR2 SDRAM controller and internal DDR2 Phy module.
DDR2 controller operates in half-rate mode (upto 533MHZ frequency).
Signed-off-by: Paul Thacker <paul.thacker@microchip.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Following commit 61bd2f75, exclude unused DDR controller from
calculating RAM size for SPL boot.
Signed-off-by: Ed Swarthout <Ed.Swarthout@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Erratum A-009663 workaround requires to set DDR_INTERVAL[BSTOPRE] to 0
before setting DDR_SDRAM_CFG[MEM_EN] and set DDR_INTERVAL[BSTOPRE]
to the desired value after DDR initialization has completed.
When DDR controller is configured to operate in auto-precharge
mode(DDR_INTERVAL[BSTOPRE]=0), this workaround is not needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
During the receive data training, the DDRC may complete on a
non-optimal setting that could lead to data corruption or
initialization failure.
Workaround: before setting MEM_EN, set DEBUG_29 register with
specific value for different data rates.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Init the rule ID, otherwise the debug code will always dump the
protection settings entry 0.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
|
|
This should make it clear that this symbol is meant to be defined by
board headers.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
If MV_DEBUG_WL is defined, DEBUG_WL_S and DEBUG_WL_D macros are missing.
In addition to that, get rid of debug output printing non-existent
counter variable.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Currently, ECC support is enabled for all Armada XP boards. So the
DDR3 driver tries to configure the controller with ECC support, even
on boards without ECC. This patch makes this ECC optional which now
can be configured on a board-per-board basis.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Phil Sutter <phil@nwl.cc>
|
|
gcc 5.1 generates this new warning (for Armada 38x platforms):
drivers/ddr/marvell/a38x/ddr3_debug.c: In function 'hws_ddr3_tip_read_training_result':
drivers/ddr/marvell/a38x/ddr3_debug.c:177:40: warning: 'sizeof' on array
function parameter 'result' will return size of 'enum hws_result (*)[1]' [-Wsizeof-array-argument]
memcpy(result, training_result, sizeof(result));
^
drivers/ddr/marvell/a38x/ddr3_debug.c:171:31: note: declared here
u32 dev_num, enum hws_result result[MAX_STAGE_LIMIT][MAX_INTERFACE_NUM])
^
Since this functions is not referenced anywhere, lets just remove it.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
