| Age | Commit message (Collapse) | Author |
|---|
|
The SPARC architecture is currently unmaintained, remove.
Cc: Francois Retief <fgretief@spaceteq.co.za>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The architecture is currently unmaintained, remove.
Cc: Benjamin Matthews <mben12@gmail.com>
Cc: Chong Huang <chuang@ucrobotics.com>
Cc: Dimitar Penev <dpn@switchfin.org>
Cc: Haitao Zhang <hzhang@ucrobotics.com>
Cc: I-SYST Micromodule <support@i-syst.com>
Cc: M.Hasewinkel (MHA) <info@ssv-embedded.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Strubel <strubel@section5.ch>
Cc: Peter Meerwald <devel@bct-electronic.com>
Cc: Sonic Zhang <sonic.adi@gmail.com>
Cc: Valentin Yakovenkov <yakovenkov@niistt.ru>
Cc: Wojtek Skulski <info@skutek.com>
Cc: Wojtek Skulski <skulski@pas.rochester.edu>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
The new function dm_remove_devices_flags() is intented for driver specific
last-stage cleanup operations before the OS is started. This patch adds
this functionality and hooks it into the common device_remove()
function.
Drivers wanting to use this feature for some last-stage removal calls,
need to add one of the DM_REMOVE_xx flags to their driver .flags.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch adds the flags parameter to device_remove() and changes all
calls to this function to provide the default value of DM_REMOVE_NORMAL
for "normal" device removal.
This is in preparation for the driver specific pre-OS (e.g. DMA
cancelling) remove support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The clock driver for the RK3399 mistakenly used (24 * 2^20) where it
should have used (24 * 10^6) in a few calculations.
This commits fixes this.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The GMAC in the RK3399 is very similar to the RK3288 variant (i.e. it
is a Designware GMAC core and requires similar configuration as the
RK3288 to switch it to RGMII and set up the TX/RX delays for Gigabit).
The key difference is that the register offsets (within the GRF block)
and bit-offsets (within those registers) used to hold the configuration
differ between the various RK32/33 CPUs.
This change refactors the gmac_rockchip.c driver to use a function
table (selected via driver_data) to factor out these differences. Each
function's implementation then matches the underlying processor.
Some collateral changes are needed in the definitions describing the
bits and offsets in the GRF are needed to prefix each set of symbolic
constants with the SoC name to avoid name clashes... and in doing so,
the shifts for masks and constants have been moved into the header
files for readability (and to make it easier to stay below 80 chars).
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed commit message typo s/factor our/factor out/:
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The Ethernet driver for the RK3288/3399 GMAC makes sure that the clock
is ungated through a call to clk_set_rate(...). Even though nothing
needs to be done on the RK3399 (the clock gates are open and the clock
is external), we need to implement enough support to at least return
success to enable driver probing.
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Due to differences in the code paths for SPL and non-SPL, some static
constant structures remain unused in each build variant. This raises
warnings with recent GCC versions (we currently use GCC-6.3).
The warnings addressed in this commit (by matching #if conditions for
the variable definition with their uses) are:
* for the SPL build:
drivers/clk/rockchip/clk_rk3399.c:53:29: warning: 'cpll_init_cfg' defined but not used [-Wunused-const-variable=]
static const struct pll_div cpll_init_cfg = PLL_DIVISORS(CPLL_HZ, 1, 2, 2);
^~~~~~~~~~~~~
drivers/clk/rockchip/clk_rk3399.c:52:29: warning: 'gpll_init_cfg' defined but not used [-Wunused-const-variable=]
static const struct pll_div gpll_init_cfg = PLL_DIVISORS(GPLL_HZ, 2, 2, 1);
^~~~~~~~~~~~~
* for the non-SPL build:
drivers/clk/rockchip/clk_rk3399.c:54:29: warning: 'ppll_init_cfg' defined but not used [-Wunused-const-variable=]
static const struct pll_div ppll_init_cfg = PLL_DIVISORS(PPLL_HZ, 2, 2, 1);
^~~~~~~~~~~~~
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
To add GMAC (Gigabit Ethernet) support (limited to RGMII only at this
point), we need support for additional pin-configuration. This commit
adds the pinctrl support for GMAC in RGMII signalling mode:
* adds a PERIPH_ID_GMAC and the mapping from IRQ number to PERIPH_ID
* adds the required defines (in the GRF support) for configuring the
GPIOC pins for RGMII
* configures the RGMII pins (in GPIOC) when requested via pinctrl
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Designware HDMI controller and phy are used in other SoCs as well. Split
out platform independent code.
DW HDMI has 8 bit registers but they can be represented as 32 bit
registers as well. Add support to select access mode.
EDID reading code use reading by blocks which is not supported by other
SoCs in general. Make it more general using byte by byte approach, which
is also used in Linux driver.
Finally, not all DW HDMI controllers are accompanied with DW HDMI phy.
Support custom phys by making controller code independent from phy code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Nickey Yang <nickey.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The Cortex-A9 socs rk3066 and rk3188 share the IP but have their own
compatible values, so add them to make the i2c on these platforms accessible.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The armclk starts in slow mode (24MHz) on the rk3188, which makes the whole
startup take a lot of time. We therefore want to at least move to the safe
600MHz value we can use with default pmic settings.
This is also the freqency the proprietary sdram-init leaves the cpu at.
For boards that have pmic control later in u-boot, we also add the option
to set the maximum frequency of 1.6GHz, if they so desire.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The config options for pinctrl on the RK3188, RK3288, RK3328 and
RK3399 previously showed up in menuconfig with the generic string
descriptor "Rockchip pin control driver" requiring one to look through
the help/full description to identify which chip each menu entry was
for.
This change renames each option with the chip-name in the description
string to make it easy to identify the configuration options in
menuconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
|
|
|
|
This includes Marvell mvpp2 patches with the ethernet support for the
ARMv8 Armada 7k/8k platforms. The ethernet patches are all acked by Joe
and he is okay with me pushing them via the Marvell tree.
|
|
|
|
|
|
Introduce CONFIG_TEGRA124_MMC_DISABLE_EXT_LOOPBACK to disable the external clock
loopback and use the internal one on SDMMC3 as per the SDMMC_VENDOR_MISC_CNTRL_0
register's SDMMC_SPARE1 bits being set to 0xfffd according to the TRM.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This is a preparation work for the support of CONFIG_BLK.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
For consistency, use an accessor to access the private data. Also for the
same reason, rename all priv_data to priv.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
As pointed out by Stefan Chulski, this variable is unused and should be
removed.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
On PPv2.2 we enable PHY polling, so we also need to configure the PHY
address in the specific PHY address rgisters.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Testing shows, that PHY polling needs to be enabled on Armada 7k/8k.
Otherwise ethernet transfers will not work correctly. PHY polling
is enabled per default after reset, so we do not need to specifically
enable it, but this makes it clearer.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Add a missing occurrance of PHY_INTERFACE_MODE_RGMII_ID, which should
be handled identical to PHY_INTERFACE_MODE_RGMII.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This patch adds the GoP (Group of Ports) and NetC (Net Complex) setup to
the Marvell mvpp2 ethernet driver for the missing port 0. This code is
mostly copied from the Marvell U-Boot version and was written by Stefan
Chulski. Please note that only SFI support have been added, as this
is the only interface that this code has been tested with. XAUI and
RXAUI support might follow at a later stage.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This patch adds the GoP (Group of Ports) and NetC (Net Complex) setup to
the Marvell mvpp2 ethernet driver. This code is mostly copied from the
Marvell U-Boot version and was written by Stefan Chulski. Please
note that only RGMII and SGMII support have been added, as these are
the only interfaces that this code has been tested with.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Read the "phy-speed" DT property to differentiate between 1 and 2.5GB
SGMII operations. Please note that its unclear right now, if this
DT property will be accepted in mainline Linux. If not, we need to
revisit this code and change it to use the accepted property.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This patch does a bit of restructuring of the probe / init functions,
mainly to allow earlier register access as it is needed for the upcoming
GoP (Group of Ports) and NetC (Net Complex) code.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This patch adds the PPv2.2 specific FIFO configuration to the mvpp2
driver. The RX FIFO packet data size is changed to the recommended
FIFO sizes. The TX FIFO configuration is newly added.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Currently, the naming of the ethernet ports is not handled correctly in
the multi-CP (Communication Processor) case. On Armada 8k, the slave-CP
also instantiates an ethernet controller with the same device ID's.
This patch now takes this into account and adds the required base-id
so that the slave-CP ethernet devices will be named "mvpp2-3 ...".
This patch also updates my Copyright notice to include 2017 as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Since Armada 7K/8K is also equipped with a newer version of the MVPP2
ethernet controller, lets enable compilation of this driver for these
platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This fixes problems noticed with the PPv2.2 A7k/8k port, when not all
elements of the descriptors had been cleared before use.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This patch moves the base_probe function mvpp2_base_probe() from the
MISC driver to the ETH driver. When integrated in the MISC driver,
probe is called too early before the U-Boot ethernet infrastructure
(especially the MDIO / PHY interface) has been initialized. Resulting
in errors in mdio_register().
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
In U-Boot the MDIO / SMI support is integrated in the mvpp2 driver,
currently only supporting the 32bit platforms (Armada 37x). This patch
now adds the A7k/8k PPv2.2 MDIO support to that the phy / mii IF
can be used as well on these platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Now that the mvpp2 driver has been modified to accommodate the support
for PPv2.2, we can finally advertise this support by adding the
appropriate compatible string.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
In PPv2.1, we have a maximum of 8 RXQs per port, with a default of 4
RXQs per port, and we were assigning RXQs 0->3 to the first port, 4->7
to the second port, 8->11 to the third port, etc.
In PPv2.2, we have a maximum of 32 RXQs per port, and we must allocate
RXQs from the range of 32 RXQs available for each port. So port 0 must
use RXQs in the range 0->31, port 1 in the range 32->63, etc.
This commit adapts the mvpp2 to this difference between PPv2.1 and
PPv2.2:
- The constant definition MVPP2_MAX_RXQ is replaced by a new field
'max_port_rxqs' in 'struct mvpp2', which stores the maximum number of
RXQs per port. This field is initialized during ->probe() depending
on the IP version.
- MVPP2_RXQ_TOTAL_NUM is removed, and instead we calculate the total
number of RXQs by multiplying the number of ports by the maximum of
RXQs per port. This was anyway used in only one place.
- In mvpp2_port_probe(), the calculation of port->first_rxq is adjusted
to cope with the different allocation strategy between PPv2.1 and
PPv2.2. Due to this change, the 'next_first_rxq' argument of this
function is no longer needed and is removed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This commit adjusts how the MVPP2_ISR_RXQ_GROUP_REG register is
configured, since it changed between PPv2.1 and PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
The PPv2.2 unit is connected to an AXI bus on Armada 7K/8K, so this
commit adds the necessary initialization of the AXI bridge.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This commit handles a few miscellaneous differences between PPv2.1 and
PPv2.2 in different areas, where code done for PPv2.1 doesn't apply for
PPv2.2 or needs to be adjusted (getting the MAC address, disabling PHY
polling, etc.).
Changed by Stefan for U-Boot:
Since mvpp2_port_power_up() has multiple callers in U-Boot, the U-Boot
version of this patch does not remove this function but simply adds the
check for MVPP21 before the mvpp2_port_fc_adv_enable() call.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This commit adjusts the mvpp2 driver register mapping and access logic
to support PPv2.2, to handle a number of differences.
Due to how the registers are laid out in memory, the Device Tree binding
for the "reg" property is different:
- On PPv2.1, we had a first area for the common registers, and then one
area per port.
- On PPv2.2, we have a first area for the common registers, and a
second area for all the per-ports registers.
In addition, on PPv2.2, the area for the common registers is split into
so-called "address spaces" of 64 KB each. They allow to access the same
registers, but from different CPUs. Hence the introduction of cpu_base[]
in 'struct mvpp2', and the modification of the mvpp2_write() and
mvpp2_read() register accessors. For PPv2.1, the compatibility is
preserved by using an "address space" size of 0.
Changed by Stefan for U-Boot:
Since we don't support multiple CPUs in U-Boot, I've removed all the
code, macros and variables introduced in the Linux patch version for this.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
In PPv2.2, the MVPP2_RXQ_DESC_ADDR_REG and MVPP2_TXQ_DESC_ADDR_REG
registers have a slightly different layout, because they need to contain
a 64-bit address for the RX and TX descriptor arrays. This commit
adjusts those functions accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This commit modifies the mvpp2_defaults_set() function to not do the
loopback and FIFO threshold initialization, which are not needed for
PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
The MVPP2_RXQ_CONFIG_REG register has a slightly different layout
between PPv2.1 and PPv2.2, so this commit adapts the functions modifying
this register to accommodate for both the PPv2.1 and PPv2.2 cases.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This commit adjusts the allocation and freeing of BM pools to support
PPv2.2. This involves:
- Checking that the number of buffer pointers is a multiple of 16, as
required by the hardware.
- Adjusting the size of the DMA coherent area allocated for buffer
pointers. Indeed, PPv2.2 needs space for 2 pointers of 64-bits per
buffer, as opposed to 2 pointers of 32-bits per buffer in
PPv2.1. The size in bytes is now stored in a new field of the
mvpp2_bm_pool structure.
- On PPv2.2, getting the physical and virtual address of each buffer
requires reading the MVPP2_BM_ADDR_HIGH_ALLOC to get the high order
bits of those addresses. A new utility function
mvpp2_bm_bufs_get_addrs() is introduced to handle this.
- On PPv2.2, releasing a buffer requires writing the high order 32 bits
of the physical address to MVPP2_BM_PHY_VIRT_HIGH_RLS_REG. We no
longer need to write the virtual address to MVPP2_BM_VIRT_RLS_REG.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This commit adds the definition of the PPv2.2 HW descriptors, adjusts
the mvpp2_tx_desc and mvpp2_rx_desc structures accordingly, and adapts
the accessors to work on both PPv2.1 and PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
