| Age | Commit message (Collapse) | Author |
|---|
|
Since the switch may be re-configured for VLAN usage in Linux (or any
other OS), lets reset the switch to its default register values upon
power-up. Otherwise network might not be available in U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Tom Rini <trini@ti.com>
|
|
Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
- dxr2: define unused pins as input
- do not enable RTC32K OSC on dxr2 board
- update default environment
- add splashpos=m,m to default environment, so splash screen is always
centered.
- adapt environment for bootcount feature
- add altbootcmd to default environment
- rut: SPL add early reset pulse for eth-phy, maXTouch and display
- rut: display timing aenderungen
- siemens boards: adapt for background color = white
- add boutcount feature for the siemens boards
store the bootcount in the environment, as we have no softreset
save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV
bootcount driver.
- change spi mode from 3 to 0 for the lcd init
- add gpio pin for lcd reset with state 0 and add mdelay
- siemens boards: use own USB id's
- add dfu serial and device number for siemens boards
Add for the siemens boards the possibility to define in dfu mode,
the iSerialNumber and the bcdDevice fields in the USB Device
descriptor.
- fix upgrade mechanism based on bootcount
Correct location of saveenv and remove not active variable.
Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to
reboot board in case of empty kernel partition. Without
these defines an empty kernel partition leads to an
abort of boot process and one remains in u-boot prompt.
- general cleanup of dxr2, pxm2 and rut boards
all:
* Remove net boot from bootcmd
Ping can cause a crash on boards without ethernet phy.
net_nfs command is used only for development
* Add reset at the end of bootcmd
In order to have an immediate reset of the boot when bootcmd
fails, add reset at the end of bootcmd.
rut:
* add nand_img_size
dxr2:
* update nand_img_size
* ddr3 timings updated with iocontrol property that can be
modified via eeprom. New default parameters from software
leveling with draco ES2.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Pascal Bach <pascal.bach@siemens.com>
Signed-off-by: Roger Meier <r.meier@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matthias Michel <matthias.michel@siemens.com>
Cc: Tom Rini <trini@ti.com>
|
|
add support for the am335x based boards from siemens:
dxr2:
- DDR3 128MiB
- NAND 256MiB
- Ethernet with external Switch SMSC LAN9303
- no PMIC
- internal Watchdog
- DFU support
pxm2:
- DDR2 512 MiB
- NAND 1024 MiB
- PMIC
- PHY atheros ar803x
- USB Host
- internal Watchdog
- DFU support
rut:
- DDR3 256 MiB
- NAND 256 MiB
- PMIC
- PHY natsemi dp83630
- external Watchdog
- DFU support
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Roger Meier <r.meier@siemens.com>
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Pascal Bach <pascal.bach@siemens.com>
Cc: Tom Rini <trini@ti.com>
|
