aboutsummaryrefslogtreecommitdiff
path: root/include/configs/nsa310s.h
AgeCommit message (Collapse)Author
2023-10-26arm: kirkwood: Enable bootstd for Zyxel NSA310S boardTony Dinh
Enable bootstd for Zyxel NSA310S board, and remove distroboot. Signed-off-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
2022-12-23global: Migrate CONFIG_EXTRA_ENV_SETTINGS to CFGTom Rini
Perform a simple rename of CONFIG_EXTRA_ENV_SETTINGS to CFG_EXTRA_ENV_SETTINGS Signed-off-by: Tom Rini <trini@konsulko.com>
2022-12-22global: Remove unused CONFIG symbolsTom Rini
This removes the following unreferenced CONFIG symbols: CONFIG_FDTADDR CONFIG_FDTFILE CONFIG_FLASH_SECTOR_SIZE CONFIG_FSL_CPLD CONFIG_HDMI_ENCODER_I2C_ADDR CONFIG_I2C_MVTWSI CONFIG_I2C_RTC_ADDR CONFIG_IRAM_END CONFIG_IRAM_SIZE CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE CONFIG_L1_INIT_RAM CONFIG_MACB_SEARCH_PHY CONFIG_MIU_2BIT_21_7_INTERLEAVED CONFIG_MTD_NAND_VERIFY_WRITE CONFIG_MVGBE_PORTS CONFIG_NETDEV CONFIG_NUM_DSP_CPUS CONFIG_PHY_BASE_ADR CONFIG_PHY_INTERFACE_MODE CONFIG_PSRAM_SCFG CONFIG_RAMBOOT_SPIFLASH CONFIG_RAMBOOT_TEXT_BASE CONFIG_RD_LVL CONFIG_ROCKCHIP_SDHCI_MAX_FREQ CONFIG_SETUP_INITRD_TAG CONFIG_SH_QSPI_BASE CONFIG_SMDK5420 CONFIG_SOCRATES CONFIG_SPI_ADDR CONFIG_SPI_FLASH_QUAD CONFIG_SPI_FLASH_SIZE CONFIG_SPI_HALF_DUPLEX CONFIG_SPI_N25Q256A_RESET CONFIG_TEGRA_SLINK_CTRLS CONFIG_TPM_TIS_BASE_ADDRESS CONFIG_UBOOT_SECTOR_COUNT CONFIG_UBOOT_SECTOR_START CONFIG_VAR_SIZE_SPL CONFIG_VERY_BIG_RAM And also: BL1_SIZE PHY_NO RESERVE_BLOCK_SIZE Signed-off-by: Tom Rini <trini@konsulko.com>
2022-08-23arm: kirkwood: nsa310s: Add Distro boot capabilityTony Dinh
- Add distro boot to board include file and deconfig file - Miscellaneous changes: - Remove Gerald from maintainer list (email bounced) - Add CONFIG_SUPPORT_PASSING_ATAGS and friends to support legacy kernel method of booting (e.g. OpenWrt) with appended DTB. - Add CONFIG_UBIFS_SILENCE_MSG to reduce binary size. Note that this patch is depended on the following patch: https://patchwork.ozlabs.org/project/uboot/patch/20220807192709.21717-1-pali@kernel.org/ Signed-off-by: Tony Dinh <mibodhi@gmail.com>
2022-06-28Complete migration of MTDPARTS_DEFAULT / MTDIDS_DEFAULT, include in environmentTom Rini
- Ensure that everyone setting mtdids= and mtdparts= is doing so via the CONFIG options. - If the CONFIG options are set, ensure that the default environment sets mtdparts / mtdids. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-28Convert CONFIG_LBA48 et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_LBA48 CONFIG_SYS_64BIT_LBA Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-02arm: kirkwood: nsa310s: Use Marvell uclass mvgbe and PHY driver for DM EthernetTony Dinh
The Zyxel NSA310s board has the network chip Marvell Alaska 88E1318S. Use uclass mvgbe and the compatible driver M88E1310 driver to bring up Ethernet. - Use uclass mvgbe to bring up the network. And remove ad-hoc code. - Remove CONFIG_RESET_PHY_R. - Enable CONFIG_PHY_MARVELL to properly configure the network. - Add phy mode RGMII to kirkwood-nsa310s.dts - Miscellaneous changes: Move constants to .c file and remove header file board/zyxel/nsa310s/nsa310s.h, add support for large USB and SATA HDDs, use BIT macro, add/cleanup comments, and cosmetic changes. Note that this patch is depended on the following patch: https://patchwork.ozlabs.org/project/uboot/patch/20220412201820.10291-1-mibodhi@gmail.com/ Signed-off-by: Tony Dinh <mibodhi@gmail.com>
2022-03-25Convert CONFIG_RESET_PHY_R to KconfigTom Rini
This converts the following to Kconfig: CONFIG_RESET_PHY_R Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-02-09Convert CONFIG_SCSI_AHCI_PLAT et al to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_SCSI_AHCI_PLAT CONFIG_SYS_SCSI_MAX_SCSI_ID CONFIG_SYS_SCSI_MAX_LUN CONFIG_SYS_SATA_MAX_DEVICE Drop CONFIG_SCSI for everything except the sandbox build. We only need one build for tests. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de>
2021-12-27Convert CONFIG_88F5182 et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_88F5182 CONFIG_BOARD_IS_OPENRD_BASE CONFIG_BOARD_IS_OPENRD_CLIENT CONFIG_BOARD_IS_OPENRD_ULTIMATE CONFIG_D2NET_V2 CONFIG_FEROCEON CONFIG_FEROCEON_88FR131 CONFIG_INETSPACE_V2 CONFIG_KW88F6192 CONFIG_KW88F6281 CONFIG_KW88F6702 CONFIG_NET2BIG_V2 CONFIG_NETSPACE_LITE_V2 CONFIG_NETSPACE_MAX_V2 CONFIG_NETSPACE_MINI_V2 CONFIG_NETSPACE_V2 CONFIG_SHEEVA_88SV131 At this point mv-plug-common.h is now only an include of mv-common.h so remove that indirection. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-27Convert CONFIG_CONS_INDEX et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CONS_INDEX CONFIG_DEBUG_UART_CLOCK CONFIG_FSL_TZPC_BP147 CONFIG_GENERIC_ATMEL_MCI CONFIG_IDENT_STRING CONFIG_LIBATA CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE CONFIG_LPC32XX_GPIO CONFIG_MP CONFIG_MPC8XXX_GPIO CONFIG_MTD_PARTITIONS CONFIG_MVGBE CONFIG_MXC_GPIO CONFIG_NR_DRAM_BANKS CONFIG_OF_BOARD_SETUP CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_OF_SYSTEM_SETUP CONFIG_PREBOOT CONFIG_ROCKCHIP_SERIAL CONFIG_RTC_ENABLE_32KHZ_OUTPUT CONFIG_RTC_MV CONFIG_SCSI_AHCI CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_SPEED CONFIG_SOFT_SPI CONFIG_SPI_FLASH_EON CONFIG_SPI_FLASH_MACRONIX CONFIG_SPI_FLASH_MTD CONFIG_SPI_FLASH_SPANSION CONFIG_SPI_FLASH_SST CONFIG_SPI_FLASH_STMICRO CONFIG_SUPPORT_RAW_INITRD CONFIG_SYS_ARCH_TIMER CONFIG_SYS_BOARD CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE CONFIG_SYS_DCACHE_OFF CONFIG_SYS_FDT_SAVE_ADDRESS CONFIG_SYS_FLASH_CFI CONFIG_SYS_FSL_ERRATUM_ESDHC135 CONFIG_SYS_HAS_SERDES CONFIG_SYS_L2CACHE_OFF CONFIG_SYS_LITTLE_ENDIAN CONFIG_SYS_LOAD_ADDR CONFIG_SYS_MMCSD_FS_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR CONFIG_SYS_NS16550 CONFIG_SYS_PLLFIN CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_TIMER_SYS_TICK_CH CONFIG_USB_EHCI_FSL CONFIG_U_QE CONFIG_VERSION_VARIABLE Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-01Convert CONFIG_USE_BOOTCOMMAND et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_USE_BOOTCOMMAND CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND CONFIG_NFSBOOTCOMMAND Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-31Convert CONFIG_SKIP_LOWLEVEL_INIT et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SKIP_LOWLEVEL_INIT CONFIG_SKIP_LOWLEVEL_INIT_ONLY In order to do this, we need to introduce SPL and TPL variants of these options so that we can clearly disable these options only in SPL in some cases, and both instances in other cases. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-19arm: kirkwood: NSA310S: Add DM SATA configsTony Dinh
Enable DM SATA, removed IDE driver, and add SATA MV driver. Signed-off-by: Tony Dinh <mibodhi@gmail.com>
2021-07-07Revert "arm: Remove nsa310s board"Tom Rini
While this platform has not yet been converted, there is active efforts to do so. Keep the platform for now. This reverts commit aa697e6904ba1b3144a46ec642d4695e7c0cdc3e. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07arm: Remove nsa310s boardTom Rini
These boards have not been converted to CONFIG_DM_USB by the deadline and is also missing conversion to CONFIG_DM. Remove it Cc: Gerald Kerma <dreagle@doukki.net> Cc: Tony Dinh <mibodhi@gmail.com> Cc: Luka Perkov <luka.perkov@sartura.hr> Signed-off-by: Tom Rini <trini@konsulko.com>
2021-04-10drivers: ata: Remove mvsata_ide driverTom Rini
The mvsata_ide driver was due for DM conversion by v2019.07. As that has long passed, remove the driver and disable it in the boards which had enabled it. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-08-23Convert CONFIG_NETCONSOLE to KconfigTom Rini
This converts the following to Kconfig: CONFIG_NETCONSOLE Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04Convert CONFIG_CMD_ASKENV et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CMD_ASKENV CONFIG_CMD_BMP CONFIG_CMD_BOOTD CONFIG_CMD_CACHE CONFIG_CMD_CRC32 CONFIG_CMD_DHCP CONFIG_CMD_ENV CONFIG_CMD_EXPORTENV CONFIG_CMD_EXT2 CONFIG_CMD_EXT4 CONFIG_CMD_FLASH CONFIG_CMD_FS_GENERIC CONFIG_CMD_FUSE CONFIG_CMD_GPIO CONFIG_CMD_GPT CONFIG_CMD_GREPENV CONFIG_CMD_I2C CONFIG_CMD_IMLS CONFIG_CMD_IMPORTENV CONFIG_CMD_LOADB CONFIG_CMD_LOADS CONFIG_CMD_MEMINFO CONFIG_CMD_MII CONFIG_CMD_MTDPARTS CONFIG_CMD_NAND CONFIG_CMD_NAND_TRIMFFS CONFIG_CMD_NFS CONFIG_CMD_PCA953X CONFIG_CMD_PCA953X_INFO CONFIG_CMD_PCI CONFIG_CMD_PING CONFIG_CMD_READ CONFIG_CMD_SF CONFIG_CMD_SPI CONFIG_CMD_SPL CONFIG_CMD_SPL_WRITE_SIZE CONFIG_CMD_TIME CONFIG_CMD_TRACE CONFIG_CMD_UBI CONFIG_CMD_UBIFS CONFIG_CMD_UNZIP CONFIG_FS_EXT4 Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04Convert CONFIG_BZIP2 et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_BZIP2 CONFIG_GZIP CONFIG_LZO CONFIG_ZLIB CONFIG_LZMA CONFIG_LZO Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-20env: Finish migration of common ENV optionsTom Rini
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-02-02Kconfig: Migrate CONFIG_BUILD_TARGETJagan Teki
Migrate CONFIG_BUILD_TARGET into Kconfig. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-22Convert CONFIG_MTD_PARTITIONS et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MTD_PARTITIONS CONFIG_MTD_DEVICE Signed-off-by: Adam Ford <aford173@gmail.com>
2018-05-29configs: remove CONFIG_SYS_MVFSChris Packham
This was being used by some Marvell boards to enable some file system related features (many of which have already been moved to Kconfig). Make the future migration of the final 2 or 3 config options easier by expanding #define CONFIG_SYS_MVFS into the options that it enables and remove CONFIG_SYS_MVFS. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-05Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULTTom Rini
We move all instances of CONFIG_MTDIDS_DEFAULT and CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files. There's a few cases here where we need to expand upon what was in the header file. Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-27net: remove CONFIG_NET_MULTIMasahiro Yamada
This macro is defined, but not referenced by anyone. I did not touch config_whitelist.txt - the CONFIG will be dropped by the next re-sync. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-08configs: Finish migration of PHY_GIGETom Rini
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-25Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_ENV_IS_IN_MMC CONFIG_ENV_IS_IN_NAND CONFIG_ENV_IS_IN_UBI CONFIG_ENV_IS_NOWHERE In fact this already exists for sunxi as a 'choice' config. However not all the choices are available in Kconfig yet so we cannot use that. It would lead to more than one option being set. In addition, one purpose of this series is to allow the environment to be stored in more than one place. So the existing choice is converted to a normal config allowing each option to be set independently. There are not many opportunities for Kconfig updates to reduce the size of this patch. This was tested with ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC And then manual updates. This is because for CHAIN_OF_TRUST boards they can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic now. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22Convert CONFIG_LZMA to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_LZMA Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22Kconfig: Add a CONFIG_IDE optionSimon Glass
At present IDE support is controlled by CONFIG_CMD_IDE. Add a separate CONFIG_IDE option so that IDE support can be enabled without requiring the 'ide' command. Update existing users and move the ide driver into drivers/block since it should not be in common/. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22Convert CONFIG_CMD_IDE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CMD_IDE Signed-off-by: Simon Glass <sjg@chromium.org>
2017-02-12flash: complete CONFIG_SYS_NO_FLASH move with renamingMasahiro Yamada
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is not completed. Finish this work by the tool. During this move, let's rename it to CONFIG_MTD_NOR_FLASH. Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH" than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will make the code more readable. Besides, negative meaning symbols do not fit in obj-$(CONFIG_...) style Makefiles. This commit was created as follows: [1] Edit "default n" to "default y" in the config entry in common/Kconfig. [2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH" [3] Rename the instances in defconfigs by the following: find . -path './configs/*_defconfig' | xargs sed -i \ -e '/CONFIG_SYS_NO_FLASH=y/d' \ -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/' [4] Change the conditionals by the following: find . -name '*.[ch]' | xargs sed -i \ -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \ -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \ -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \ -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/' [5] Modify the following manually - Rename the rest of instances - Remove the description from README - Create the new Kconfig entry in drivers/mtd/Kconfig - Remove the old Kconfig entry from common/Kconfig - Remove the garbage comments from include/configs/*.h Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-28disk: convert CONFIG_DOS_PARTITION to KconfigPatrick Delaunay
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
2016-04-25configs: Re-sync with cmd/KconfigTom Rini
Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2015-11-29arm: kirkwood: add ZyXEL NSA310S deviceGerald Kerma
This patch add ZyXEL NSA310S 1-Bay Media Server The ZyXEL NSA310S device is a Kirkwood based NAS: - SoC: Marvell 88F6702 1000Mhz - SDRAM memory: 256MB DDR2 400Mhz - Gigabit ethernet: PHY Marvell 88E1318 - Flash memory: 128MB - 1 Power button - 1 Power LED (blue) - 4 Status LED (green) - 1 Copy/Sync button - 1 Reset button - 1 SATA II port - 2 USB 2.0 ports (front and back) - Smart fan Signed-off-by: Gerald Kerma <dreagle@doukki.net> Signed-off-by: Tony Dinh <mibodhi@gmail.com> Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-10 08:15:24 +0000