aboutsummaryrefslogtreecommitdiff
path: root/include/configs/wandboard.h
AgeCommit message (Collapse)Author
2019-11-20env: Finish migration of common ENV optionsTom Rini
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-10-08imx: wandboard: convert FEC support to DM_ETHAnatolij Gustschin
Remove CONFIG_DM_ETH conversion warning to avoid board removal. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-09-21imx: wandboard: fix splash logo drawingAnatolij Gustschin
After mxc_ipuv3 DM_VIDEO conversion showing splash image doesn't work. Fix this. Also enable white on black console configuration as it used to be with cfb_console driver. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-07-07imx6: wandboard: allow booting from MMC 2Heinrich Schuchardt
One of the SD-CARD slots on the Wandboard Quad B1 is MMC 2. Enable it as a boot device. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-04-13imx6: wandboard: convert to DM_I2CAnatolij Gustschin
Allow building with DM_I2C enabled. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-13imx6: wandboard: convert to DM_PMICAnatolij Gustschin
Enable DM_PMIC_PFUZE100 driver and add PMIC description to DTS. Rework power_init_board() code. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-13imx6: wandboard: convert to DM_VIDEOAnatolij Gustschin
Enable DM_VIDEO in defconfig. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-13imx6: wandboard: convert to DM_USBAnatolij Gustschin
Drop CONFIG_USB_MAX_CONTROLLER_COUNT and enable DM_USB in defconfig. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-13imx: move CONFIG_VIDEO_IPUV3 to defconfigsAnatolij Gustschin
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2018-08-17Convert CONFIG_MII et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-16configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-18wandboard: Remove hardcoded baudrate from "console" variableOtavio Salvador
We should use the baudrate variable available inside U-Boot environment to allow it to be changed dynamically. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-08Migrate CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to KconfigAlex Kiernan
Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Petr Vorel <petr.vorel@gmail.com> Reviewed-by: Petr Vorel <petr.vorel at gmail.com>
2018-04-08treewide: Migrate CONFIG_DISPLAY_BOARDINFO_LATE to KconfigMario Six
Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc> [trini: Re-run migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-23Remove config_distro_defaults.hAdam Ford
With the contents of config_distro_defaults.h migrated to Kconfig, we can remove this header file completely Signed-off-by: Adam Ford <aford173@gmail.com>
2017-12-12ata: Migrate CONFIG_LIBATA to KconfigTuomas Tynkkynen
This symbol enables some library code used by various SATA drivers, so make this a non-user-visible symbol select'ed by the respective drivers, and let moveconfig handle the rest. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12ata: Migrate CONFIG_DWC_AHSATA to KconfigTuomas Tynkkynen
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-11-17Kconfig: Introduce USE_BOOTCOMMAND and migrate BOOTCOMMANDTom Rini
We first introduce CONFIG_USE_BOOTCOMMAND, similar to CONFIG_USE_BOOTARGS. We then migrate CONFIG_BOOTCOMMAND for most CONFIG_DISTRO_DEFAULT users. In some cases platforms have a complex scheme around this usage, and these have been defered for the moment so that platform maintainers can work on a migration plan. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2017-10-31wandboard: Add support for the MX6QP variantFabio Estevam
Add support for the latest MX6QP wandboard variant. Based on Richard Hu's work from Technexion's U-Boot tree. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-10-12wandboard: Add support for the latest revd1 revisionFabio Estevam
Latest wandboard hardware revision is revd1, which brings the following new features: - PFUZE100 PMIC - AR8035 Ethernet PHY - Upgrade Wifi/BT chip to BCM4339/BCM43430. The detection mechanism is to probe the PMIC and when it is found, then the revision of the board is revd1. As the detection is done via PMIC, we need to print the board version at a later stage via CONFIG_DISPLAY_BOARDINFO_LATE and also need to disable CONFIG_DISPLAY_BOARDINFO, which is done much earlier. Make the necessary adjustments for the AR8035 PHY to work on revd1. Based on Richard Hu's work from Technexion's U-Boot tree. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-09-11ipu_common: Let the MX6 IPU clock be calculated in run-timeFabio Estevam
MX6Q/QP IPU operates at 264MHz and MX6DL IPU at 198MHz. When running a SPL target, which supports multiple MX6 variants we cannot properly setup the IPU clock frequency via CONFIG_IPUV3_CLK option as such decision is done in build-time currently. Remove the CONFIG_IPUV3_CLK option and let the IPU clock frequency be configured in run-time on mx6. Reported-by: Eric Nelson <eric@nelint.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com> Reviewed-by: Stefano Babic <sbabic@denx.de> [agust: fixed #endif in cgtqmx6eval.h] Signed-off-by: Anatolij Gustschin <agust@denx.de>
2017-08-16Merge git://www.denx.de/git/u-boot-imxTom Rini
Update pfla02 for setenv changes and PHYLIB/etc migration to Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-07Move PHYLIB to KconfigAlexandru Gagniuc
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-07-28arm: imx: Enable booting from SATA on wandboard.Vagrant Cascadian
Enable booting from SATA on the wandboard. Sata support was already enabled, but distro_bootcmd is not configured to boot from it. Signed-off-by: Vagrant Cascadian <vagrant@debian.org> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-07-25Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_ENV_IS_IN_MMC CONFIG_ENV_IS_IN_NAND CONFIG_ENV_IS_IN_UBI CONFIG_ENV_IS_NOWHERE In fact this already exists for sunxi as a 'choice' config. However not all the choices are available in Kconfig yet so we cannot use that. It would lead to more than one option being set. In addition, one purpose of this series is to allow the environment to be stored in more than one place. So the existing choice is converted to a normal config allowing each option to be set independently. There are not many opportunities for Kconfig updates to reduce the size of this patch. This was tested with ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC And then manual updates. This is because for CHAIN_OF_TRUST boards they can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic now. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-12wandboard: Use PARTUUID to specify the rootfs locationFabio Berton
Currently the rootfs location is passed via mmcblk number and the problem with this approach is that the mmcblk number for the eMMC changes depending on the kernel version. In order to avoid such issue, use UUID method to specify the rootfs location. This change was made based on U-Boot commit: - ca4f338e2efece5196eb2178e5f7d07be828da6e Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-07-11Convert CONFIG_CMD_SATA to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CMD_SATA Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-05-22Convert CONFIG_CMD_HDMIDETECT to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CMD_HDMIDETECT Note that we cannot do 'default y if VIDEO' because this option is only enabled for a small subset of mx6 boards. Also this command is is not a great implementation (it doesn't use driver model). Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-15Kconfig: USB: Migrate existing USB_EHCI_xxx optionsTom Rini
The following options are migrated over fully now: - USB_EHCI_ATMEL - USB_EHCI_MARVELL - USB_EHCI_MX6 - USB_EHCI_MX7 - USB_EHCI_MSM - USB_EHCI_ZYNQ - USB_EHCI_GENERIC This also requires fixing the depends on USB_EHCI_MARVELL as it's used by Orion5X and Kirkwood as well. Cc: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Marek Vasut <marex@denx.de>
2017-05-15Kconfig: USB: Migrate CONFIG_USB_EHCI_HCD users to KconfigTom Rini
Migrate the rest of the users of CONFIG_USB_EHCI_HCD over to Kconfig. For a few SoCs, imply or default y this if USB is enabled. In some cases we had not already migrated to CONFIG_USB so do that as well. Cc: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Marek Vasut <marex@denx.de>
2017-05-15Kconfig: USB: Migrate CONFIG_USB_EHCI to CONFIG_USB_EHCI_HCDTom Rini
In order to be able to migrate the various SoC EHCI CONFIG options we first need to finish the switch from CONFIG_USB_EHCI to CONFIG_USB_EHCI_HCD. Cc: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Marek Vasut <marex@denx.de>
2017-04-30Convert CONFIG_CMD_BMODE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CMD_BMODE Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Make this default y and depend on mx5/6/7] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-28arm: Clean up MACH_TYPE_xxx usage after re-sync of mach-typesTom Rini
With the latest mach-types values we have many instances where we no longer need to define a value and a few cases where the name (but not value) have changed slightly. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-25Convert CONFIG_BOARD_EARLY_INIT_F to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_BOARD_EARLY_INIT_F Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-21config: Move CONFIG_BOARD_LATE_INIT to defconfigsJagan Teki
Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Jagan Teki <jagan@openedev.com>
2016-11-29arm: imx: wandboard: fix compile error if CONFIG_VIDEO is deactivatedSven Ebenfeld
When I tried to deactivate VIDEO support for the Wandboard, it still tried to initialize the Framebuffer and so on. That is the reason for the added ifdefs. CONFIG_VIDEO is enabled in the configuration as default and therefore nothing changes for the default user. The structs mx6dl_i2c2_pad_info and mx6q_i2c2_pad_info are only available when CONFIG_IPUV3 are set and should not be tried to access, when that define is not defined. Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
2016-10-23Convert CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-23Convert CONFIG_VGA_AS_SINGLE_DEVICE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_VGA_AS_SINGLE_DEVICE Once we migrate to driver model for video, we should be able to drop this option. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-10-23Convert CONFIG_CFB_CONSOLE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CFB_CONSOLE Signed-off-by: Simon Glass <sjg@chromium.org>
2016-10-23Convert CONFIG_SYS_CONSOLE_IS_IN_ENV and CONFIG_CONSOLE_MUX to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_SYS_CONSOLE_IS_IN_ENV CONFIG_CONSOLE_MUX Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Re-order, re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-23Convert CONFIG_VIDEO to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_VIDEO Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-10-04wandboard: Remove videoargs scriptFabio Estevam
The videoargs script is kernel version dependent and since wandboard uses distro config, there is no need to handle videoargs locally. In case such video related settings are needed, then the proper location would be the distro extlinux.conf or boot.scr files. So remove 'videoargs' script. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-09-16Convert CONFIG_SPL_MMC_SUPPORT to KconfigSimon Glass
Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16Convert CONFIG_SPL_LIBCOMMON_SUPPORT to KconfigSimon Glass
Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-09configs: Migrate CONFIG_USB_STORAGETom Rini
In some cases we were missing CONFIG_USB=y so enable that when needed. Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-07-19wandboard: move environment partition farther from u-boot.imgAlexey Brodkin
Recently I started to notice that u-boot.img built for Wandboard by some toolchains becomes so large that it basically overlaps with U-Boot environment area on SD-card. According to http://wiki.wandboard.org/index.php/Boot-process#sdcard_boot_data_layout Wandboard's SD-card layout is as follows: ------------------------------>8--------------------------- Acked-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Fabio Estevam <fabio.estevam@nxp.com> ========================================================== 1. 0x00000000 Reserved For MBR 2. 0x00000200 512 Secondary Image Table (optional) 3. 0x00000400 1024 uBoot Image (Starting From IVT) 4. 0x00060000 393216 start of uboot env (size:8k) 5. 0x00062000 end of uboot env 6. 0x00100000 1048576 Linux kernel start 7. 0x0076AC00 7777280 start of partition 1 ------------------------------>8--------------------------- So for U-Boot we have 383kB (392192 bytes). But in up to date U-Boot for Wandboard we build separately a) SPL b) u-boot.img which gives us a bit more detailed SD-card layout: ------------------------------>8--------------------------- ========================================================== 1. 0x00000000 Reserved For MBR 2. 0x00000200 512 Secondary Image Table (optional) 3. 0x00000400 1024 SPL 4. 0x00011400 70656 u-boot.img 5. 0x00060000 393216 start of uboot env (size:8k) 6. 0x00062000 end of uboot env ... ------------------------------>8--------------------------- >From that layout we may calculate amount of space reserved for u-boot.img. It's just 315kb (322560 bytes). Now if I build U-Boot with Sourcery CodeBench ARM 2014.05 produced u-boot.img is already more than we expected (323840 bytes instead of "< 322560"): ------------------------------>8--------------------------- ls -la u-boot.img -rw-rw-r-- 1 user user 323840 Jul 5 07:38 u-boot.img ------------------------------>8--------------------------- Funny enough if I rebuild U-Boot with ARM toolchain available in my Fedora 23 distro u-boot.img becomes a little bit smaller: ------------------------------>8--------------------------- ls -la u-boot.img -rw-rw-r-- 1 user user 322216 Jul 5 07:39 u-boot.img ------------------------------>8--------------------------- What's worse this problem might not affect people most of the time because what happens people would just copy u-boot.img on SD-card and live in happiness with it... well until somebody attempts to save environment in U-Boot with "saveenv" command which will simply overwrite the very end of u-boot.img. That will lead to unusable SD-card until user dd u-boot.img on SD-card again. I may foresee this issue in the future to become more visible once we add more features in U-Boot for Wandboard or just existing code base becomes bulkier and people will consistently get larger u-boot.img files produced. IMHO there's an obvious solution for all that - just move U-Boot's env to the very end of the gap between U-Boot and the first real partition on the SD-card. This patch will follow 8fb9eea5653796 ("mx6sabre_common: Fix U-Boot corruption after 'saveenv'"). So env is still not in the very end of the gap (obviously 256kb is way too much for U-Boot's env) but at least we have now the same partitioning for i.MX6 boards. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Peter Robinson <pbrobinson@gmail.com> Cc: Tom Rini <trini@konsulko.com> Cc: Peter Korsgaard <peter@korsgaard.com> Cc: Wolfgang Denk <wd@denx.de>
2016-07-12wandboard: enable SATA with imx6qGilles Chanteperdrix
Signed-off-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
2016-04-25configs: Re-sync with cmd/KconfigTom Rini
Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-25configs: Re-sync almost all of cmd/KconfigTom Rini
This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: Tom Rini <trini@konsulko.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-14 07:02:27 +0000