aboutsummaryrefslogtreecommitdiff
path: root/include/netdev.h
AgeCommit message (Collapse)Author
2023-02-07armada: usb: net: Drop unused USB driversSimon Glass
These are not used. Drop the drivers and Kconfig option. Also drop an old declaration in the netdev.h header. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-12-22net: Remove more legacy functionsTom Rini
Remove some of the board and arch specific non-DM_ETH helper code. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-08-08net: mpc8xx_fec: Migrate to DM_ETHChristophe Leroy
Migrate mpc8xx_fec driver to DM_ETH. Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-09-21net: remove unused CONFIG_DRIVER_AT91EMAC_*Eugen Hristev
AT91EMAC driver is unused, thus removing. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-07-22net: Use phys_addr_t for SMC net device addressesPeter Hoyes
Use same type as eth_device->iobase and support addresses greater than INT_MAX. Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2021-04-20net: calxedagmac: Convert to DM_ETHAndre Przywara
To squash that nasty warning message and make better use of the newly gained OF_CONTROL feature, let's convert the calxedagmac driver to the "new" driver model. The conversion is pretty straight forward, mostly just adjusting the use of the involved data structures. The only actual change is the required split of the receive routine into a receive and free_pkt part. Also this allows us to get rid of the hardcoded platform information and explicit init calls. This also uses the opportunity to wrap the code decoding the MMIO register base address, to make it safe for using PHYS_64BIT later. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-02-02common: Drop asm/global_data.h from common headerSimon Glass
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-17treewide: convert bd_t to struct bd_info by coccinelleMasahiro Yamada
The Linux coding style guide (Documentation/process/coding-style.rst) clearly says: It's a **mistake** to use typedef for structures and pointers. Besides, using typedef for structures is annoying when you try to make headers self-contained. Let's say you have the following function declaration in a header: void foo(bd_t *bd); This is not self-contained since bd_t is not defined. To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h> #include <asm/u-boot.h> void foo(bd_t *bd); Then, the include direcective pulls in more bloat needlessly. If you use 'struct bd_info' instead, it is enough to put a forward declaration as follows: struct bd_info; void foo(struct bd_info *bd); Right, typedef'ing bd_t is a mistake. I used coccinelle to generate this commit. The semantic patch that makes this change is as follows: <smpl> @@ typedef bd_t; @@ -bd_t +struct bd_info </smpl> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
2020-05-01net: Fix warning when including netdev.h on DM systemsMarek Vasut
If the DM_ETH is enabled and netdev.h is included somewhere, the struct eth_device may not be defined, yet it is used in the header file as an argument to fecmxc_register_mii_postcall. Add forward declaration to remove the warning. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2019-09-04net: dwc_et_qos: update weak function board_interface_eth_initPatrick Delaunay
Align the board and driver prototype for board_interface_eth_init to avoid execution issue (the interface_type parameter is defined as int or phy_interface_t). To have a generic weak function (it should be reused by other driver) I change the prototype to use directly udevice. This prototype is added in netdev.h to allow compilation check and avoid warning when compiling with W=1 on file board/st/stm32mp1/stm32mp1.c warning: no previous prototype for 'board_interface_eth_init'\ [-Wmissing-prototypes] int board_interface_eth_init(int interface_type, .... ^~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25net: davinci_emac: convert to using the driver modelBartosz Golaszewski
Now that we removed all legacy boards selecting TI_EMAC we can completely convert the driver code to using the driver model. This patch also updates all remaining users of davinci_emac. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Tested-by: Adam Ford <aford173@gmail.com> #am3517-evm & da850-evm Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2018-11-05net: ftgmac100: convert to driver modelCédric Le Goater
The driver is based on the previous one and the code is only adapted to fit the driver model. The support for the Faraday ftgmac100 controller is the same with MAC and MDIO bus support for RGMII/RMII modes. Configuration is updated to enable compile again. At this stage, the driver compiles but is not yet functional. Signed-off-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-08mips: au1x00: Remove support for these SoCsTom Rini
The only platform left for the AU1x00 SoCs was the pb1x00 platform, an apparent clone of the dbau1x00 platform. As pb1x00 had no listed maintainer I am assuming that it is also orphaned. Remove this platform and then remove the unused SoC support. Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-05-23net: Drop CONFIG_TSI108_ETHTuomas Tynkkynen
Last user of this driver went away in June 2015 in commit d928664f4101e24 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support") Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-13net: fec_mxc: simplify fec_get_miibusPeng Fan
No need to provide two prototype for this function. Use ulong for the first parameter, then this function could be shared for DM/non DM case. Signed-off-by: Peng Fan <peng.fan@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22net: Drop CONFIG_ENC28J60Tuomas Tynkkynen
Last user of this driver went away in October 2014 in commit d58a9451e7339ed4 ("ppc/arm: zap EMK boards"). Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-23net: Remove Xilinx ll_temac driverMichal Simek
ll_temac driver was used by Xilinx Microblaze big endian and Xilinx ppc405/ppc440 SoCs. ppc support was removed by: "powerpc: remove 4xx support" (sha1: 98f705c9cefdfdba62c069821bbba10273a0a8ed) and Microblaze BE is not tested for a long time that's why this driver can be removed because none is going to updated it to DM anyway. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-07-28net: fec_mxc: adjust prototype of fec_get_miibus() for DM_ETHLothar Waßmann
commit 306dd7dabd64 ("net: fec_mxc: fix PHY initialization bug with CONFIG_DM_ETH") has broken the build of the fec_mxc driver with CONFIG_DM_ETH enabled because it changed the parameters passed to *fec_get_miibus() without changing the functions prototype. This patch fixes up the prototype of fec_get_miibus() for the DM_ETH case. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
2017-06-16powerpc, 82xx: remove some missed mpc82xx remainsHeiko Schocher
we removed 82xx support. Missed some 82xx remains, remove them now. Signed-off-by: Heiko Schocher <hs@denx.de>
2017-06-16powerpc, 5xxx, 512x: remove support for mpc5xxx and mpc512xHeiko Schocher
There was for long time no activity in the mpx5xxx area. We need to go further and convert to Kconfig, but it turned out, nobody is interested anymore in mpc5xxx, so remove it. Signed-off-by: Heiko Schocher <hs@denx.de>
2017-04-05SPARC: RemoveTom Rini
The SPARC architecture is currently unmaintained, remove. Cc: Francois Retief <fgretief@spaceteq.co.za> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-05-24net: Remove unused mv88e61xx switch driverKevin Smith
No boards are using this driver. Remove in preparation for a new driver with integrated PHY support. Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de>
2016-01-27net: emaclite: Move driver to DMMichal Simek
Move driver to DM. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Remove ancient OF probe functionMichal Simek
Prepare for DM move. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: axi_emac: Move driver to DMMichal Simek
Move driver to DM. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-12-07net: gem: Move driver to DMMichal Simek
- Enable DM_ETH by default for Zynq and ZynqMP - Remove board_eth_init code - Change miiphy_read function to return value instead of error code based on DM requirement - Do not enable EMIO DT support by default Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-12-07net: gem: Remove zynq_gem_of_init()Michal Simek
This function was used for OF init before DM. Remove this function as the part of move to DM. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-11-12net: zap altera_tse_initialize prototypesThomas Chou
Zap the altera_tse_initialize() prototypes, since it is converted to driver model. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Reviewed-by: Marek Vasut <marex@denx.de>
2015-09-09net: pch_gbe: Convert to driver modelBin Meng
This commit converts pch_gbe ethernet driver to driver model. Since this driver is only used by Intel Crown Bay board, the conversion does not keep the non-dm version. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Simon Glass <sjg@chromium.org>
2015-05-04sunxi: emac: Remove non driver-model codeHans de Goede
All sunxi boards now use the driver-model, so remove the non driver-model code. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04sunxi: gmac: Move sunxi_gmac_initialize proto out of netdev.hHans de Goede
netdev.h should not be included in driver-model enabled builds (doing so causes compiler warnings about struct eth_driver not being declared), but we do use sunxi_gmac_initialize in the driver-model case, so move it out of netdev.h . Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-04-10lpc32xx: add Ethernet supportAlbert ARIBAUD \(3ADEV\)
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-03-24net: Add Intel Topcliff GMAC driverBin Meng
Add a new driver for the Gigabit Ethernet MAC found on Intel Topcliff Platform Controller Hub. Tested under 10/100 half/full duplex and 1000 full duplex modes using ping and tftpboot commands. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-02-24ARM: remove cm4008 and cm41xx board supportMasahiro Yamada
These are still non-generic boards. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Greg Ungerer <greg.ungerer@opengear.com> Acked-by: Marek Vasut <marex@denx.de>
2015-01-21net: gem: Use phys_addr_t instead of int for addressesMichal Simek
Use phys_addr_t for physical address declaration. It is also unsigned type instead of sign. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-10-23net: mvneta.c: Add support for the ethernet controller of the Marvell Armada ↵Stefan Roese
XP SoC This patch adds support for the NETA ethernet controller which is integrated in the Marvell Armada XP SoC's. This port is based on the Linux driver which has been stripped of the in U-Boot unused portions. Tested on the Marvell MV78460 eval board db-78460-bp. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Joe Hershberger <joe.hershberger@gmail.com> Tested-by: Luka Perkov <luka@openwrt.org>
2014-08-30arm: bcm281xx: net: Add Ethernet DriverJiandong Zheng
The Broadcom StarFighter2 Ethernet driver is used in multiple Broadcom SoC(s) and: - supports multiple MAC blocks, - provides support for the Broadcom GMAC. This driver requires MII and PHYLIB. Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com> Signed-off-by: Steve Rae <srae@broadcom.com>
2014-08-21drivers: net: remove dead driversMasahiro Yamada
The following configs are not defined at all: - CONFIG_INCA_IP_SWITCH - CONFIG_PBL2800_ETHER - CONFIG_PHY_ICPLUS Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-07-06net: Rename and cleanup sunxi (Allwinner) emac driverStefan Roese
There have been 3 versions of the sunxi_emac support patch during its development. Somehow version 2 ended up in upstream u-boot where as the u-boot-sunxi git repo got version 3. This bumps the version in upstream u-boot to version 3 of the patch: - Initialize MII clock earlier so mii access to allow independent use - Name change from WEMAC to EMAC to match mainline kernel & chip manual - Cosmetic code cleanup Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-05-25sunxi: add gmac Ethernet supportIan Campbell
Add support for the GMAC Ethernet controller on Allwinner A20 (sun7i) processors. Enable for the Cubietruck. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Tom Rini <trini@ti.com>
2014-04-20MIPS: drop incaip boardDaniel Schwierzeck
This is dead hardware and no one is interested in making the necessary changes for upcoming features like generic board or driver model. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Wolfgang Denk <wd@denx.de>
2014-03-04net: gem: Add OF initialization supportMichal Simek
Gem can be directly initialized from DTB. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-03-04net: emaclite: Fix OF initializationMichal Simek
- Add xilinx_emaclite_of_init to netdev.h - Remove global data pointer from the driver - Add better handling for error state. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-07net/designware - switch driver to phylib usageAlexey Brodkin
With this change driver will benefit from existing phylib and thus custom phy functionality implemented in the driver will go away: * Instantiation of the driver is now much shorter - 2 parameters instead of 4. * Simplified phy management/functoinality in driver is replaced with rich functionality of phylib. * Support of custom phy initialization is now done with existing "board_phy_config". Note that after this change some previously used config options (driver-specific PHY configuration) will be obsolete and they are simply substituted with similar options of phylib. For example: * CONFIG_DW_AUTONEG - no need in this one. Autonegotiation is enabled by default. * CONFIG_DW_SEARCH_PHY - if one wants to specify attached phy explicitly CONFIG_PHY_ADDR board config option has to be used, otherwise automatically the first discovered on MDIO bus phy will be used I believe there's no need now in "doc/README.designware_eth" because user only needs to instantiate the driver with "designware_initialize" whose prototype exists in "include/netdev.h". Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Vipin Kumar <vipin.kumar@st.com> Cc: Stefan Roese <sr@denx.de> Cc: Mischa Jonker <mjonker@synopsys.com> Cc: Shiraz Hashim <shiraz.hashim@st.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Amit Virdi <amit.virdi@st.com> Cc: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2013-07-24Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
2013-06-24net: add Faraday FTMAC110 10/100Mbps ethernet supportKuo-Jung Su
Faraday FTMAC110 10/100Mbps supports half-word data transfer for Linux. However it has a weird DMA alignment issue: (1) Tx DMA Buffer Address: 1 bytes aligned: Invalid 2 bytes aligned: O.K 4 bytes aligned: O.K (2) Rx DMA Buffer Address: 1 bytes aligned: Invalid 2 bytes aligned: O.K 4 bytes aligned: Invalid!!! Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Tom Rini <trini@ti.com>
2013-06-24net: ks8851_mll: add ethernet supportRoberto Cerati
The device interface is 16 bits wide. All the available packets are read from the incoming fifo. Signed-off-by: Roberto Cerati <roberto.cerati@bticino.it> Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it> [voice.shen@atmel.com: address comments from review results] [voice.shen@atmel.com: clean up for submit] Signed-off-by: Bo Shen <voice.shen@atmel.com> Tested-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
2013-06-24net: Add sunxi (Allwinner) wemac driverHenrik Nordström
This patch adds support for the WEMAC, the ethernet controller included in the Allwinner A10 SoC. It will get used in the upcoming A10 board support. From: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
2013-05-30Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD
Conflicts: common/cmd_fpga.c drivers/usb/host/ohci-at91.c
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-14 23:10:01 +0000