| Age | Commit message (Collapse) | Author |
|---|
|
log2 of the device block size serves as the shift value used to calculate
the block number to read in file systems when implementing avaiable block
sizes.
It is needed quite often in file systems thus it is pre-calculated and
stored in the block device descriptor.
Signed-off-by: Egbert Eich <eich@suse.com>
|
|
Disks beyond 2T in size use blocksizes of 4096 bytes. However a lot of
code in u-boot still assumes a 512 byte blocksize.
This patch fixes the handling of GPTs.
Signed-off-by: Egbert Eich <eich@suse.com>
|
|
The restoration of GPT table (both primary and secondary) is now possible.
Function 'gpt_restore' presents example of partition restoration process.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
Each EFI partition table entry contains a UUID. Extend U-Boot's struct
disk_partition to be able to store this information, and modify
get_partition_info_efi() to fill it in.
The implementation of uuid_string() was derived from the Linux kernel,
tag v3.6-rc4 file lib/vsprintf.c function uuid_string().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Rework get_device_and_partition() to:
a) Implement a new partition ID of "auto", which requests that U-Boot
search for the first "bootable" partition, and fall back to the first
valid partition if none is found. This way, users don't need to
specify an explicit partition in their commands.
b) Make use of get_device().
c) Add parameter to indicate whether returning a whole device is
acceptable, or whether a partition is mandatory.
d) Make error-checking of the user's device-/partition-specification
more complete. In particular, if strtoul() doesn't convert all
characters, it's an error rather than just ignored.
The resultant device/partition returned by the function will be as
follows, based on whether the disk has a partition table (ptable) or not,
and whether the calling command allows the whole device to be returned
or not.
(D and P are integers, P >= 1)
D
D:
No ptable:
!allow_whole_dev: error
allow_whole_dev: device D
ptable:
device D partition 1
D:0
!allow_whole_dev: error
allow_whole_dev: device D
D:P
No ptable: error
ptable: device D partition P
D:auto
No ptable:
!allow_whole_dev: error
allow_whole_dev: device D
ptable:
first partition in device D with bootable flag set.
If none, first valid paratition in device D.
Note: In order to review this patch, it's probably easiest to simply
look at the file contents post-application, rather than reading the
patch itself.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
[swarren: Rob implemented scanning for bootable partitions. I fixed a
couple of issues there, switched the syntax to ":auto", added the
error-checking rework, and ":0" syntax for the whole device]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
This patch introduces function get_device(). This looks up a
block_dev_desc_t from an interface name (e.g. mmc) and device number
(e.g. 0). This function is essentially the non-partition-specific
prefix of get_device_and_partition().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
All block device related commands (scsiboot, fatload, ext2ls, etc.) have
simliar duplicated device and partition parsing and selection code. This
adds a common function to replace various implementations.
The new function has an enhancement over current versions. If no device
or partition is specified on the command line, the bootdevice env variable
will be used (scsiboot does this).
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Determine which partitions are bootable/active. In the partition listing,
print "Boot" for partitions with the bootable/active flag set.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Indent at the same level as other struct members.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
If we don't want to build support for any partition types we can now
add #undef CONFIG_PARTITIONS in a board config file to keep this from
being compiled in. Otherwise boards assume this is compiled in by
default
Signed-off-by: Matthew McClintock <msm@freescale.com>
|
|
Erase is a very basic function since the begin of sd specification is
announced. Although we could write a bulk of full 0xff memory to the
range to take place of erase, it is more convenient and safe to
implement the erase function itself.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
|
|
Mflash is fusion memory device mainly targeted consumer eletronic and
mobile phone.
Internally, it have nand flash and other hardware logics and supports
some different operation (ATA, IO, XIP) modes.
IO mode is custom mode for the host that doesn't have IDE interface.
(Many mobile targeted SoC doesn't have IDE bus)
This driver support mflash IO mode.
Followings are brief descriptions about IO mode.
1. IO mode based on ATA protocol and uses some custom command. (read
confirm, write confirm)
2. IO mode uses SRAM bus interface.
Signed-off-by: unsik Kim <donari75@gmail.com>
|
|
The GUID (Globally Unique Identifier) Partition Table (GPT) is a part
of EFI. See http://en.wikipedia.org/wiki/GUID_Partition_Table
Based on linux/fs/partitions/efi.[ch]
Signed-off-by: Richard Retanubun <RichardRetanubun@RugggedCom.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
- add the SATA framework
- add the SATA command line
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|
MMC support for X_Scale PXA is broken and does not work.
Mainly, the mmc_init() function cannot recognize current SD/MMC cards.
There were already some patches around the world but none of them was
merged into the official u-boot tree.
This patch makes order fixing this issue. Resubmit after code cleanup.
Applied and tested on PXA 270 (TrizepsIV module).
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
The pxa255_idp being an old unmaintained board showed several issues:
1. CONFIG_INIT_CRITICAL was still defined.
2. Neither CONFIG_MAC_PARTITION nor CONFIG_DOS_PARTITION was defined.
3. Symbol flash_addr was undeclared.
4. The boards lowlevel_init function was still called memsetup.
5. The TEXT_BASE was still 0xa3000000 rather than 0xa3080000.
6. Using -march=armv5 instead of -march=armv5te resulted in lots of
'target CPU does not support interworking' warnings on recent compilers.
7. The PXA's serial driver redefined FFUART, BTUART and STUART used as
indexes rather than the register definitions from the pxa-regs header
file. Renamed them to FFUART_INDEX, BTUART_INDEX and STUART_INDEX to
avoid any ambiguities.
8. There were several redefinition warnings concerning ICMR, OSMR3,
OSCR, OWER, OIER, RCSR and CCCR in the PXA's assembly start file.
9. The board configuration file was rather outdated.
10. The part header file defined the vendor, product and revision arrays
as unsigned chars instead of just chars in the block_dev_desc_t
structure.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
|
|
buffer pointers
Block device read/write is anonymous data; there is no need to use a
typed pointer. void * is fine. Also add a hook for block_read functions
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Preparation for future patches which support block device writing
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Each of the filesystem drivers duplicate the get_dev routine. This change
merges them into a single function in part.c
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
* Patch by Rune Torgersen, 16 Apr 2004:
LBA48 fixes
* Patches by Pantelis Antoniou, 16 Apr 2004:
- Fix some compile problems;
add "once" functionality for the netretry variable
|
|
Fix buffer overflow in IDE identification
|
|
|
|
add FAT support for IDE, SCSI and USB
* Patches by Gleb Natapov, 2 Sep 2003:
- cleanup of POST code for unsupported architectures
- MPC824x locks way0 of data cache for use as initial RAM;
this patch unlocks it after relocation to RAM and invalidates
the locked entries.
* Patch by Gleb Natapov, 30 Aug 2003:
new I2C driver for mpc107 bridge. Now works from flash.
* Patch by Dave Ellis, 11 Aug 2003:
- JFFS2: fix typo in common/cmd_jffs2.c
- JFFS2: fix CFG_JFFS2_SORT_FRAGMENTS option
- JFFS2: remove node version 0 warning
- JFFS2: accept JFFS2 PADDING nodes
- SXNI855T: add AM29LV800 support
- SXNI855T: move environment from EEPROM to flash
- SXNI855T: boot from JFFS2 in NOR or NAND flash
* Patch by Bill Hargen, 11 Aug 2003:
fixes for I2C on MPC8240
- fix i2c_write routine
- fix iprobe command
- eliminates use of global variables, plus dead code, cleanup.
|
|
(autoscript, bmp, bsp, fat, mmc, nand, portio, ...)
|
|
- remove trailing white space, trailing empty lines, C++ comments, etc.
- split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c)
* Patches by Kenneth Johansson, 25 Jun 2003:
- major rework of command structure
(work done mostly by Michal Cendrowski and Joakim Kristiansen)
|
|
Add code for AmigaOne board
(preliminary merge to U-Boot, still WIP)
* Patch by Jon Diekema, 12 Nov 2002:
- Adding URL for IEEE OUI lookup
- Making the autoboot #defines dependent on CONFIG_AUTOBOOT_KEYED
being defined.
- In the CONFIG_EXTRA_ENV_SETTINGS #define, the root-on-initrd and
root-on-nfs macros are designed to switch how the default boot
method gets defined.
|
|
|
