aboutsummaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2011-11-29mpc8xxx: update module_type values from JEDEC DDR3 SPD SpecificationIra W. Snyder
Newer JEDEC DDR3 SPD Specifications define several additional values for the DDR3 module_type field which were undefined when this code was written. Update the code to handle the newer module types. Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Cc: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29powerpc/p3060qds: Add board related support for P3060QDS platformShengzhou Liu
The P3060QDS is a Freescale reference board for the six-core P3060 SOC. P3060QDS Board Overview: Memory subsystem: - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus) - 128M Bytes NOR flash single-chip memory - 16M Bytes SPI flash - 8K Bytes AT24C64 I2C EEPROM for RCW Ethernet: - Eight Ethernet controllers (4x1G + 4x1G/2.5G) - Three VSC8641 PHYs on board (2xRGMII + 1xMII) - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3 PCIe: Two PCI Express 2.0 controllers/ports USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board I2C: Four I2C controllers UART: Supports two dUARTs up to 115200 bps for console RapidIO: Two RapidIO, sRIO1 and sRIO2 Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29powerpc/85xx: clean up and document the QE/FMAN microcode macrosTimur Tabi
Several macros are used to identify and locate the microcode binary image that U-boot needs to upload to the QE or Fman. Both the QE and the Fman use the QE Firmware binary format to package their respective microcode data, which is why the same macros are used for both. A given SOC will only have a QE or an Fman, so this is safe. Unfortunately, the current macro definition and usage has inconsistencies. For example, CONFIG_SYS_FMAN_FW_ADDR was used to define the address of Fman firmware in NOR flash, but CONFIG_SYS_QE_FW_IN_NAND contains the address of NAND. There's no way to know by looking at a variable how it's supposed to be used. In the future, the code which uploads QE firmware and Fman firmware will be merged. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29powerpc/85xx: CONFIG_FSL_SATA_V2 should be defined in config_mpc85xx.hTimur Tabi
Macro CONFIG_FSL_SATA_V2 is defined if the SOC has a V2 Freescale SATA controller, so it should be defined in config_mpc85xx.h instead of the various board header files. So now CONFIG_FSL_SATA_V2 is always defined on the P1013, P1022, P2041, P3041, P5010, and P5020. It was already defined for the P1010 and P1014. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-27dataflash: fix parameters order in write_dataflash()Igor Grinberg
Fix parameters order in write_dataflash() function extern declaration in the header file. Parameters order, as in function definition, should be: addr_dest, addr_src, size. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2011-11-27davinci_sonata: define CONFIG_MACH_TYPE for davinci_sonata boardChristian Riesch
This patch fixes the build breakage for the davinci_sonata board. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Sergey Kubushyn <ksi@koi8.net> Cc: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-27davinci_schmoogie: define CONFIG_MACH_TYPE for davinci_schmoogie boardChristian Riesch
This patch fixes the build breakage for the davinci_schmoogie board. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Sergey Kubushyn <ksi@koi8.net> Cc: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-27arm: a320evb: define mach-type in board config fileYan-Pai Chen
MACH_TYPE_FARADAY was dropped from mach-types.h. Add it back to board config file. Signed-off-by: Yan-Pai Chen <ypchen@faraday-tech.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2011-11-27Fix Stelian's email addressStelian Pop
Change my old email address which is no longer valid. Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-11-27Merge branch 'master' of git://git.denx.de/u-boot-mmcWolfgang Denk
* 'master' of git://git.denx.de/u-boot-mmc: Revert "mmc: retry the cmd8 to meet 74 clocks requirement in the spec" mmc: mv_sdhci: Fix host version read for Armada100
2011-11-27microblaze: usable uart16550 for big endian systemsStephan Linz
As a result of the commit 6833260 the uart16550 driver is broken for Microblaze big endian systems, because of the missing 3 byte offset. Other than as described, not all U-Boot BSP will treat properly the 3 byte offset. This why prefer to mask out the 3 byte offset in general and setup correct _REG_SIZE value depending on edianess. Signed-off-by: Stephan Linz <linz@li-pro.net> Tested-by: Michal Simek <monstr@monstr.eu>
2011-11-25mmc: mv_sdhci: Fix host version read for Armada100Ajay Bhargav
sdhci_readw does not work for host version read in Armada100 series SoCs. This patch fix this issue by making a sdhci_readl call to get host version. Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
2011-11-23Fix clash between IH_ARCH_NDS32 and IH_ARCH_SANDBOXStefan Kristiansson
NDS32 and SANDBOX architecture were sharing the same IH_ARCH number Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Acked-by: Macpaul Lin <macpaul@andestech.com> Acked-by: Marek Vasut <marek.vasut@gmail.com>
2011-11-22env: clean env_common.c checkpatch and code styleIgor Grinberg
Cleanup the env_common.c checkpatch warnings, errors and coding style. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2011-11-22env: clean env_dataflash.c checkpatch and code styleIgor Grinberg
Cleanup the env_dataflash.c checkpatch warnings, errors and coding style. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2011-11-22env: clean cmd_nvedit.c checkpatch and code styleIgor Grinberg
Cleanup the cmd_nvedit.c checkpatch warnings, errors and coding style. There are 10 wanrings left about the simple_strtoul() function: WARNING: simple_strtoul is obsolete, use kstrtoul instead #359: FILE: cmd_nvedit.c:359: + load_addr = simple_strtoul(argv[2], NULL, 16); ... total: 0 errors, 10 warnings, 1043 lines checked Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2011-11-22env: move extern environment[] to environment.hIgor Grinberg
Extract all extern declarations for environment out of c files into the environment.h header. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2011-11-22env: move extern default_environment[] to environment.hIgor Grinberg
Extract all extern declarations for default_environment[] out of c files into the environment.h header. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Cc: Stefan Roese <sr@denx.de> Acked-by: Stefan Roese <sr@denx.de>
2011-11-22common: move extern char console_buffer[] to common.hIgor Grinberg
Extract all extern declarations for console_buffer[] out of c files into the common.h header. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Cc: Frank Gottschling <fgottschling@eltec.de> Cc: Murray Jensen <Murray.Jensen@csiro.au>
2011-11-22env: clean environment.h checkpatch and code styleIgor Grinberg
Though one warning left: WARNING: do not add new typedefs #149: FILE: u-boot/include/environment.h:149: +typedef struct environment_s { total: 0 errors, 1 warnings, 181 lines checked Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2011-11-22Define uintptr_t as long int to simplify printf() format stringsSimon Glass
If uintptr_t can be either an unsigned int or an unsigned long int, it is tricky to use it in a printf() format string. This changes it to unsigned long int consistently. This should do the right thing on both 32-bit and 64-bit architectures. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-11-21Merge branch 'sr@denx.de' of git://git.denx.de/u-boot-stagingWolfgang Denk
* 'sr@denx.de' of git://git.denx.de/u-boot-staging: Makefile: Add the missing dependency for spl target gpio: Adapt PCA9698 to standard GPIO API
2011-11-21Merge branch 'master' of git://git.denx.de/u-boot-niosWolfgang Denk
* 'master' of git://git.denx.de/u-boot-nios: nios2: Offer ft_board_setup() capability and call fdt_fixup_ethernet(). board/nios2-generic: Use altera_pio driver and remove board specific driver gpio: Add driver for Altera's PIO core nios2: Pseudo implement dcache_status/enable/disable()
2011-11-18gpio: Adapt PCA9698 to standard GPIO APIDirk Eibach
Signed-off-by: Dirk Eibach <eibach@gdsys.de> Acked-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Stefan Roese <sr@denx.de>
2011-11-16Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: api: export LCD device to external apps font: split font data from video_font.h tools: logo: split bmp arrays from bmp_logo.h lcd: add clear and draw bitmap declaration VIDEO: mx3fb: GCC4.6 fix build warnings Powerpc/DIU: Fixed the 800x600 and 1024x768 resolution bug
2011-11-16Merge branch 'master' of git://git.denx.de/u-boot-videoWolfgang Denk
* 'master' of git://git.denx.de/u-boot-video: api: export LCD device to external apps font: split font data from video_font.h tools: logo: split bmp arrays from bmp_logo.h lcd: add clear and draw bitmap declaration VIDEO: mx3fb: GCC4.6 fix build warnings Powerpc/DIU: Fixed the 800x600 and 1024x768 resolution bug
2011-11-16Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: arm, davinci: add DAVINCI_MMC_CLKID arm, davinci_emac: fix driver bug if more then 3 PHYs are detected arm, davinci: da850/dm365 lowlevel cleanup omap5: Add omap5_evm board build support. omap4/5: Add support for booting with CH. omap5: emif: Add emif/ddr configurations required for omap5 evm omap5: clocks: Add clocks support for omap5 platform. omap5: Add minimal support for omap5430. omap: Checkpatch fixes omap4: make omap4 code common for future reuse GCC4.6: Squash warnings in onenand_base.c GCC4.6: Fix common/usb.c on xscale OneNAND: Add simple OneNAND SPL PXA: vpac270: Enable the new generic MMC driver PXA: Cleanup serial_pxa PXA: Drop csb226 and innokom boards (unmaintained) m28evk: Fix comment about the number of RAM banks mx31: Fix checkpatch warnings in generic.c mx31: Use proper IO accessor for GPR register mx31: Remove duplicate definition for GPR register qong: Use generic function for configuring GPR register M28EVK: Enable USB HOST support iMX28: Add USB HOST driver iMX28: Add USB and USB PHY register definitions M28: Add memory detection into SPL iMX28: Fix ARM vector handling M28: Add doc/README.m28 documentation M28: Add MMC SPL iMX28: Add support for DENX M28EVK board iMX28: Add u-boot.sb target to Makefile iMX28: Add image header generator tool iMX28: Add driver for internal RTC iMX28: Add GPMI NAND driver iMX28: Add APBH DMA driver iMX28: Add SPI driver iMX28: Add GPIO control iMX28: Add I2C bus driver iMX28: Add PINMUX control FEC: Add support for iMX28 quirks iMX28: Add SSP MMC driver iMX28: Initial support for iMX28 CPU MX25: zmx25: GCC4.6 fix build warnings da850: add new config file for AM18xx BeagleBoard: config: Switch to ttyO2 OMAP3: Change omap3_evm maintainer devkit8000: Fix NAND SPL on boards with 256MB NAND integrator: enable Vpp and disable flash protection integrator: add system controller header integrator: make flash writeable on boot integrator: use io-accessors for board init integrator: move text offset to config integrator: pass configs for core modules ARM: remove superfluous setting of arch_number in board specific code. SPL: Allow ARM926EJS to avoid compiling in the CPU support code integrator: do not test first part of the memory arm: a320: fix broken timer ARM: define CONFIG_MACH_TYPE for all ronetix boards dm646x: pass board revision info to kernel dm646x: add new configuration for dm6467T arm, davinci: Fix setting of the SDRAM configuration register arm, davinci: Remove the duplication of LPSC functions arm, davinci: Rename AM1808 lowlevel functions to DA850 da8xxevm: fix build error ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE
2011-11-16Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
* 'master' of git://git.denx.de/u-boot-arm: arm, davinci: add DAVINCI_MMC_CLKID arm, davinci_emac: fix driver bug if more then 3 PHYs are detected arm, davinci: da850/dm365 lowlevel cleanup omap5: Add omap5_evm board build support. omap4/5: Add support for booting with CH. omap5: emif: Add emif/ddr configurations required for omap5 evm omap5: clocks: Add clocks support for omap5 platform. omap5: Add minimal support for omap5430. omap: Checkpatch fixes omap4: make omap4 code common for future reuse GCC4.6: Squash warnings in onenand_base.c GCC4.6: Fix common/usb.c on xscale OneNAND: Add simple OneNAND SPL PXA: vpac270: Enable the new generic MMC driver PXA: Cleanup serial_pxa PXA: Drop csb226 and innokom boards (unmaintained) m28evk: Fix comment about the number of RAM banks mx31: Fix checkpatch warnings in generic.c mx31: Use proper IO accessor for GPR register mx31: Remove duplicate definition for GPR register qong: Use generic function for configuring GPR register M28EVK: Enable USB HOST support iMX28: Add USB HOST driver iMX28: Add USB and USB PHY register definitions M28: Add memory detection into SPL iMX28: Fix ARM vector handling M28: Add doc/README.m28 documentation M28: Add MMC SPL iMX28: Add support for DENX M28EVK board iMX28: Add u-boot.sb target to Makefile iMX28: Add image header generator tool iMX28: Add driver for internal RTC iMX28: Add GPMI NAND driver iMX28: Add APBH DMA driver iMX28: Add SPI driver iMX28: Add GPIO control iMX28: Add I2C bus driver iMX28: Add PINMUX control FEC: Add support for iMX28 quirks iMX28: Add SSP MMC driver iMX28: Initial support for iMX28 CPU MX25: zmx25: GCC4.6 fix build warnings da850: add new config file for AM18xx BeagleBoard: config: Switch to ttyO2 OMAP3: Change omap3_evm maintainer devkit8000: Fix NAND SPL on boards with 256MB NAND integrator: enable Vpp and disable flash protection integrator: add system controller header integrator: make flash writeable on boot integrator: use io-accessors for board init integrator: move text offset to config integrator: pass configs for core modules ARM: remove superfluous setting of arch_number in board specific code. SPL: Allow ARM926EJS to avoid compiling in the CPU support code integrator: do not test first part of the memory arm: a320: fix broken timer ARM: define CONFIG_MACH_TYPE for all ronetix boards dm646x: pass board revision info to kernel dm646x: add new configuration for dm6467T arm, davinci: Fix setting of the SDRAM configuration register arm, davinci: Remove the duplication of LPSC functions arm, davinci: Rename AM1808 lowlevel functions to DA850 da8xxevm: fix build error ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE
2011-11-16Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: Fix constness of the fdt void pointer in fdt_getprop_u32_default Add some missing endian conversions in fdt_support.c
2011-11-16Merge branch 'master' of git://git.denx.de/u-boot-fdtWolfgang Denk
* 'master' of git://git.denx.de/u-boot-fdt: Fix constness of the fdt void pointer in fdt_getprop_u32_default Add some missing endian conversions in fdt_support.c
2011-11-16Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: powerpc/85xx: Fix builds of P1020/P2020RDB-PC_36BIT_NAND arch/powerpc/cpu/mpc8xxx/ddr/ctrl_regs.c: Fix GCC 4.6 build warning arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c: Fix GCC 4.6 build warning arch/powerpc/cpu/mpc8xxx/ddr/options.c: Fix GCC 4.6 build warning drivers/qe/uec.c: Fix GCC 4.6 build warning drivers/usb/host/ehci-fsl.c: Fix GCC 4.6 build warning drivers/net/fm/fm.c: Fix GCC 4.6 build warning board/sbc8560/sbc8560.c: Fix GCC 4.6 build warning board/sbc8548/sbc8548.c: Fix GCC 4.6 build warning board/freescale/mpc8569mds/mpc8569mds.c: Fix GCC 4.6 build warning board/freescale/mpc8568mds/mpc8568mds.c: Fix GCC 4.6 build warning board/freescale/mpc8548cds/mpc8548cds.c: Fix GCC 4.6 build warning board/freescale/common/pixis.c: Fix GCC 4.6 build warning board/freescale/common/cds_pci_ft.c: Fix GCC 4.6 build warning arch/powerpc/cpu/mpc8xxx/fsl_lbc.c: Fix GCC 4.6 build warning arch/powerpc/cpu/mpc85xx/tlb.c: Fix GCC 4.6 build warning arch/powerpc/cpu/mpc85xx/cpu_init.c: Fix GCC 4.6 build warning phylib: Enable AR8021 phy support powerpc/85xx: Set max alloc length to 10MB on P1022DS powerpc/mpc85xx: Set SYSCLK to the required frequency powerpc/85xx: Fix NAND SPL support powerpc/85xx: Fix MPC8572DS NAND build fsl_ifc: Fixed a bug in the erratum handling code for IFC_A003399 powerpc/85xx: Add support for Book-E MMU Arch v2.0 powerpc/85xx: Make inclusion of USB device fixup conditional powerpc/85xx: Fix warning for USB device-fixup powerpc/85xx: resize the boot page TLB before relocating CCSR powerpc/85xx: verify the current address of CCSR before relocating it powerpc/85xx: add some missing sync instructions in the CCSR relocation code powerpc/85xx: fix some comments in the CCSR relocation code powerpc/85xx: fix definition of MAS register macros powerpc/mpc8548cds: Fix network initialization powerpc/mpc8548: Add workaround for erratum NMG_eTSEC129 powerpc/QorIQ: fix network frame manager TBI PHY address settings
2011-11-16Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
* 'master' of git://git.denx.de/u-boot-mpc85xx: powerpc/85xx: Fix builds of P1020/P2020RDB-PC_36BIT_NAND arch/powerpc/cpu/mpc8xxx/ddr/ctrl_regs.c: Fix GCC 4.6 build warning arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c: Fix GCC 4.6 build warning arch/powerpc/cpu/mpc8xxx/ddr/options.c: Fix GCC 4.6 build warning drivers/qe/uec.c: Fix GCC 4.6 build warning drivers/usb/host/ehci-fsl.c: Fix GCC 4.6 build warning drivers/net/fm/fm.c: Fix GCC 4.6 build warning board/sbc8560/sbc8560.c: Fix GCC 4.6 build warning board/sbc8548/sbc8548.c: Fix GCC 4.6 build warning board/freescale/mpc8569mds/mpc8569mds.c: Fix GCC 4.6 build warning board/freescale/mpc8568mds/mpc8568mds.c: Fix GCC 4.6 build warning board/freescale/mpc8548cds/mpc8548cds.c: Fix GCC 4.6 build warning board/freescale/common/pixis.c: Fix GCC 4.6 build warning board/freescale/common/cds_pci_ft.c: Fix GCC 4.6 build warning arch/powerpc/cpu/mpc8xxx/fsl_lbc.c: Fix GCC 4.6 build warning arch/powerpc/cpu/mpc85xx/tlb.c: Fix GCC 4.6 build warning arch/powerpc/cpu/mpc85xx/cpu_init.c: Fix GCC 4.6 build warning phylib: Enable AR8021 phy support powerpc/85xx: Set max alloc length to 10MB on P1022DS powerpc/mpc85xx: Set SYSCLK to the required frequency powerpc/85xx: Fix NAND SPL support powerpc/85xx: Fix MPC8572DS NAND build fsl_ifc: Fixed a bug in the erratum handling code for IFC_A003399 powerpc/85xx: Add support for Book-E MMU Arch v2.0 powerpc/85xx: Make inclusion of USB device fixup conditional powerpc/85xx: Fix warning for USB device-fixup powerpc/85xx: resize the boot page TLB before relocating CCSR powerpc/85xx: verify the current address of CCSR before relocating it powerpc/85xx: add some missing sync instructions in the CCSR relocation code powerpc/85xx: fix some comments in the CCSR relocation code powerpc/85xx: fix definition of MAS register macros powerpc/mpc8548cds: Fix network initialization powerpc/mpc8548: Add workaround for erratum NMG_eTSEC129 powerpc/QorIQ: fix network frame manager TBI PHY address settings
2011-11-16Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: adp-ag101p: add product into MAINTAINERS list adp-ag101p: Add SoC and board support of ag101p nds32: fix data section of linker script dwcddr21mctl: Synopsys DWC DDR2/1 Memory Controller andes_pcu.h: header file of andes_pcu power control unit
2011-11-15api: export LCD device to external appsChe-Liang Chiou
This patch exports LCD info-query and bitmap-rendering functions to external apps. This patch is tested on a Seaboard. Because the LCD driver is not yet upstreamed, the test was done in a local downstream repo. Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
2011-11-15font: split font data from video_font.hChe-Liang Chiou
While video_font.h is useful even without referencing the font data, it is not possible to be included multiple times because it defines font data array right in the header. This patch splits the font data array into video_font_data.h and so now video_font.h can be included multiple times. This at least solves the code duplication in board/mcc200/lcd.c. Signed-off-by: Che-Liang Chiou <clchiou@chromium.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-11-15tools: logo: split bmp arrays from bmp_logo.hChe-Liang Chiou
The generated header bmp_logo.h is useful even outside common/lcd.c for the logo dimension. However, the problem is, the generated bmp_logo.h cannot be included multiple times because bmp_logo_palette[] and bmp_logo_bitmap[] are defined in the bmp_logo.h. This patch fixes this by defining these arrays in another header bmp_logo_data.h and in bmp_logo.h only declaring these arrays. Signed-off-by: Che-Liang Chiou <clchiou@chromium.org> Acked-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-11-15lcd: add clear and draw bitmap declarationChe-Liang Chiou
The functions for clearing and drawing bitmaps on the screen were not exposed publicly and are made public in this patch in preparation for implementing the display interface of api_public.h. Signed-off-by: Che-Liang Chiou <clchiou@chromium.org> Acked-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-11-15omap5: Add omap5_evm board build support.Sricharan
This patch adds the build support for the omap5_evm board. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15omap4/5: Add support for booting with CH.Sricharan
Configuration header(CH) is 512 byte header attached to an OMAP boot image that will help ROM code to initialize clocks, SDRAM etc and copy U-Boot directly into SDRAM. CH can help us in by-passing SPL and directly boot U-boot, hence it's an alternative for SPL. However, we intend to support both CH and SPL for OMAP4/5. Initialization done through CH is limited and is not equivalent to that done by SPL. So U-Boot has to distinguish between the two cases and handle them accordingly. This patch takes care of doing this. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15omap5: Add minimal support for omap5430.Sricharan
This patch adds the minimal support for OMAP5. The platform and machine specific headers and sources updated for OMAP5430. OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture. It's a dual core SOC with GIC used for interrupt handling and SCU for cache coherency. Also moved some part of code from the basic platform support that can be made common for OMAP4/5. Rest is kept out seperately. The same approach is followed for clocks and emif support in the subsequent patches. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15OneNAND: Add simple OneNAND SPLMarek Vasut
This introduces small OneNAND loader, fitting into 1kB of space (smallest possible OneNAND RAM size). Some devices equipped with such crappy chips will use this. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Scott Wood <scottwood@freescale.com> V2: Introduce spl_onenand_load_image() to load data from OneNAND in SPL V3: Cleanup, align with nand_spl. Skip whole blocks.
2011-11-15PXA: vpac270: Enable the new generic MMC driverMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-11-15PXA: Drop csb226 and innokom boards (unmaintained)Marek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Robert Schwebel <robert@schwebel.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-11-13Fix constness of the fdt void pointer in fdt_getprop_u32_defaultGabe Black
The function fdt_getprop_u32_default doesn't modify the fdt, so it can use a const void * for its fdt argument. Signed-off-by: Gabe Black <gabeblack@chromium.org>
2011-11-11phylib: Enable AR8021 phy supportXie Xiaobo
Enable AR8021 as it used on Freescale boards: P1020RDB-PC, P1021RDB-PC, P2020RDB-PC, P1020UTM-PC, and P1020MSBG-PC. Signed-off-by: Xie Xiaobo <X.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-11powerpc/85xx: Set max alloc length to 10MB on P1022DSJerry Huang
In order to support 1920x01080 resolution, we must increase the alloc length. Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> CC: Anatolij Gustschin <agust@denx.de> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-11m28evk: Fix comment about the number of RAM banksFabio Estevam
m28evk has one bank of RAM. Fix the comment. Cc: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marek.vasut@gmail.com>
2011-11-11M28EVK: Enable USB HOST supportMarek Vasut
This enables the second port, aka. the port with the USB connector on the M28EVK. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Remy Bohmer <linux@bohmer.net>
2011-11-11M28: Add memory detection into SPLMarek Vasut
This code allows the DDR DRAM size to be detected at runtime. The RAM size is stored into two scratch registers, from which it is then fetched in U-Boot. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-11-11iMX28: Fix ARM vector handlingMarek Vasut
This patch introduces proper ARM vector handling for i.MX28 CPU. This issue wasn't addressed because the interrupts weren't enabled on any ARMv5 core, therefore the issue wasn't noticed earlier. In previous implementation, the vectoring code used by i.MX28 CPU when an exception happened was that of the SPL. With this change, the branch target when an exception happens can be reconfigured by U-Boot. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>