| Age | Commit message (Collapse) | Author |
|---|
|
Warp has a MAX77696 PMIC connected via I2C1 bus.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Add support for MAX77696 PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
It seems that many comments were copied from the I2C uclass, so adjust
the comments for the thermal class.
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
This patch adds support for the "OHB System AG" baseboard
with is equipped with the TQMa6S SoM.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
|
|
|
|
Currently PCI expansion ROM address is assigned by a call to
pciauto_setup_rom() outside of the pci auto config process.
This does not work when expansion ROM is on a device behind
PCI bridge where bridge's memory limit register was already
programmed to a value that does not cover the newly assigned
expansion ROM address. To fix this, we should configure the
ROM address during the auto config process.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Commit afbbd413a fixed this for non-driver-model. Make sure that the driver
model code handles this also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Adjust minnowmax to use driver model for PCI. This requires adding a device
tree node to specify the ranges, removing the board-specific PCI code and
ensuring that the host bridge is configured.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Enable a SPI environment and store it in a suitable place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
Store VESA parameters to Linux setup header so that vesafb driver
in the kernel could work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Jian Luo <jian.luo4@boschrexroth.de>
|
|
Enable graphics support on Intel Crown Bay board With the help of
vgabios for Intel TunnelCreek IGD. Tested with an external LVDS
panel connected to X4 connector and SDVO adapter connected to X9
connector on the board.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Move X86_OPTION_ROM_FILE & X86_OPTION_ROM_ADDR to arch/x86/Kconfig
and rename them to VGA_BIOS_FILE & VGA_BIOS_ADDR which depend on
HAVE_VGA_BIOS. The new names are consistent with other x86 binary
blob options like HAVE_FSP/FSP_FILE/FSP_ADDR.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Only the PCI controller has access to the PCI region information. Make sure
to use the controller (rather than any attached bridges) when configuring
devices.
This corrects a failure to scan and configure devices when driver model is
enabled for PCI.
Also add a comment to explain the problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Introduce a new method 'get_count' in the UCLASS_CPU ops to get
the number of CPUs in the system.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
|
|
|
|
Since commit 09c3280754f8 (mtd, nand: Move common functions from
cmd_nand.c to common place), NAND commands would not work at all
on large devices.
=> nand read 80000000 10000 10000
NAND read: Offset exceeds device limit
=> nand erase 100000 100000
NAND erase: Offset exceeds device limit
The type of the "size" of "struct mtd_info" is uint64_t, while
mtd_arg_off_size() and mtd_arg_off() treat chipsize as int type.
The chipsize is wrapped around if the argument is given with 2GB
or larger.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This patch enabled the USB/EHCI support for the Marvell
DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
|
Configure and enable the SATA/SCSI (AHCI) support for the Marvell
DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
|
This patch adds support for the common AHCI controller on the Marvell
Armada 38x.
Tested on the Marvell DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
|
This patch adds MMC/SDIO support to the Marvell DB-88F6820-GP board
configuration. Including support for the common partitions and
filesystems.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
|
According to README.mxc_ocotp the OCOTP is a stanard i.MX6 SoC feature
so centralise the config in mx6_common.h so functionality is standard
across all boards
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
|
|
When compling under 64bit platforms, there are lots of warnings,
like:
drivers/block/ahci.c:114:18: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
u8 *port_mmio = (u8 *)probe_ent->port[port].port_mmio;
^
drivers/block/ahci.c: In function ?.hci_host_init?.
drivers/block/ahci.c:218:49: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
probe_ent->port[i].port_mmio = ahci_port_base((u32) mmio, i);
......
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
|
|
Baltos has USB0 connected to a USB hub and thus is host-only. USB1
is connected to microUSB connector and thus should use OTG mode.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
|
|
Because it is possible for the MTD number to change, causing a
filesystem mount failure, we should use the volume name instead
of the MTD number and let Linux resolve the correct one.
Signed-off-by: Mike Scherban <m-scherban@ti.com>
|
|
On STM32F429 gpio PC6/PC7 can be allocated for USART6, as
reported in the comment.
But current code in
drivers/serial/serial_stm32.c
uses a different gpio mapping (PG14/PG9) for USART6.
Fix the comment to match current code in the driver.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: u-boot@lists.denx.de
To: Kamil Lulko <rev13@wp.pl>
Cc: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: u-boot@lists.denx.de
To: Kamil Lulko <rev13@wp.pl>
Cc: Tom Rini <trini@konsulko.com>
|
|
Use one mtd partition for rootfs and configuration by
means of ubi volumes and get rid of configuration partition.
We can use partition layout for both 256MB and 512MB flash.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
Specify proper U-Boot offset, enable prefetch mode,
increase bootm size and add FIT fallback, if board_name
is not present in kernel-fit.itb image.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
|
|
This action is need to make I2C communication with PMIC
stable for low temperature. Print current I2C speed in
SPL for visual control.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
|
|
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add CONFIG_SYS_GENERIC_BOARD to board's config header.
Boot-tested on am3517_evm board.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
|
|
This also came from Linux - according to this thread it has a GPL v2
license like arch/arm/mach-omap2/mux.h:
http://lists.denx.de/pipermail/u-boot/2015-June/217827.html
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Ingrid Viitanen <ingrid.viitanen@nokia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Instead of selecting REGEX when NET is enabled, make it the default, but
allow boards that are tiny to disable it and lose functionality on all
but the first Ethernet adapter.
cm-bf548, bf538f-ezkit, and bf533-stamp need this. None appear to have
more than one Ethernet interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This patch uses generic 'load' command instead of 'fatload' for 'loadbootscript', 'loadimage' and 'loadfdt' for mx53loco board.
This allows to use EXT partition instead of FAT, while keeping FAT compatibility.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Jason Liu <r64343@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <r64343@freescale.com>
|
|
Conflicts:
configs/tbs2910_defconfig
configs/tqma6q_mba6_mmc_defconfig
configs/tqma6q_mba6_spi_defconfig
configs/tqma6s_mba6_mmc_defconfig
configs/tqma6s_mba6_spi_defconfig
include/configs/mx6_common.h
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This patch does all the board configurations required to use the qspi
controller & attached spi flash memory.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
|
|
CONFIG_OF_SEPARATE is default define with CONFIG_OF_CONTROL, removing
this define from the board file to avoid multiple definition warning.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
|
|
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
|
|
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
|
|
Increase console IO buffer size to 1024 from the previous value of 256.
The previous value was too short for editing environment variables like
ubiboot from the console.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
|
|
This commit moves:
- CONFIG_SPI_FLASH_BAR
from include/configs/*.h into configs/*_defconfigs
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Rename CONFIG_SF_DATAFLASH into CONFIG_SPI_FLASH_DATAFLASH
as it follows the naming convention same as remaining configs.
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
- Adjust tab spaces
- Add comments
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Move common functions from cmd_nand.c (for calculating offset
and size from cmdline paramter) to common place, so they could
used from other commands which use mtd partitions.
For onenand the arg_off_size() is left in common/cmd_onenand.c.
It should use now the common arg_off() function, but as I could
not test onenand I let it there ...
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
|
|
Enable Driver Model SPI for ls1021atwr board.
DSPI and QSPI only be enabled when boot from QSPI.
DSPI and QSPI are compatible under Driver Model SPI.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
Enable Driver Model SPI for ls1021aqds board.
DSPI and QSPI is enabled only when boot from QSPI.
DSPI and QSPI are compatible under Driver Model SPI.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
|
