| Age | Commit message (Collapse) | Author |
|---|
|
The usbboot environment variable has 'usb start' command but
doesn't have the corresponding 'usb stop' command. This breaks
usb peripheral mode if tried after 'run usbboot' fails to load
the images in usb host mode.
Fix it here by adding 'usb stop' command in usbboot env.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Commit 181bd9dc61d2da88b78f1c1138a685dae39354d6 introduced Kconfig selection
for SYS_PROMPT. When applying the new picosam9g45 board this change slipped
through, adopt it.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Various U-Boot adoptions/extensions to MTD/NAND/UBI did not take buffer
alignment into account which led to failures of the following form:
ERROR: v7_dcache_inval_range - start address is not aligned - 0x1f7f0108
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x1f7f1108
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Scott Wood <scottwood@freescale.com>
[trini: Add __UBOOT__ hunk to lib/zlib/zutil.c due to malloc.h in common.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This patch brings the following changes to the x600 board support:
- Add USB EHCI support
- Add VFAT support for USB key file access
- Increase malloc size (for UBI / UBIFS usage)
- Enable Thumb mode to save some image space
- Remove unreferenced CONFIG_STACKSIZE
- Remove unreferenced CONFIG_SPL_NO_PRINTF
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
|
|
The SPL implementation for SPEAr600 is older than the common SPL
infrastructure. This patch now moves the SPEAr600 SPL over to the
common SPL code.
Tested on the only SPEAr board that currently uses SPL in mainline
U-Boot, the x600.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
|
|
Currently u-boot stack is defined at the beginning of MSMC RAM.
This is a problem for uart boot mode as ROM downloads directly to
starting of MSMC RAM.
Fixing it by moving stack to the end of u-boot section and shifting
SYS_TEXT_BASE to the start of MSMC RAM.
Updated division of MSMC RAM is shown below:
-----------------------------------------
| | | |
| U-Boot text |U-Boot | SPL text |
| download | Stack | Download + |
| | | SPL_BSS + |
| | | SPL_STACK |
-----------------------------------------
[1] [2] [3] [4]
[1] SYS_TEXT_BASE (Start of MSMC RAM)
[2] SPL_TEXT_BASE - GBL_DATA_SIZE
[3] SPL_TEXT_BASE
[4] END of SPL
[1] + [2] is at least 1M on all platforms, so no chance of overlap.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Remove ag101 and ag102 support
Signed-off-by: Kun-Hua Huang <kunhua@andestech.com>
|
|
Add nds32 ag101p generic board support.
Signed-off-by: Kun-Hua Huang <kunhua@andestech.com>
|
|
Raspberry Pi by default loads the FDT to 0x00000100 so set fdt_addr_r to
match and move scriptaddr to 0x02000000 to avoid clobbering the FDT.
Signed-off-by: Jonathan Liu <net147@gmail.com>
|
|
|
|
So far we only enabled one legacy serial port on the SMSC LPC47m
superio chipset on Intel Crown Bay board. As the board also has
dual PS/2 ports routed out, enable the keyboard controller which
is i8042 compatible so that we can use PS/2 keyboard and mouse.
In order to make PS/2 keyboard work with the VGA console, remove
CONFIG_VGA_AS_SINGLE_DEVICE. To boot Linux kernel with PIC mode
using PIRQ routing table, adjust the mask in the device tree to
reserve irq12 which is used by PS/2 mouse.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
- Rename CamelCase variables to conform U-Boot coding convention
- Rename wait_until_kbd_output_full() to kbd_output_full()
- Change to use macros for i8042 command and control register bits
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
These functions are defined by macros so do not show up with grep. Add
a comment to help.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add an api to enable and configure the integrated keyboard controller
on SMSC LPC47m superio chipset. It also adds several macros to help
future extension.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
When booting as a coreboot payload, the framebuffer details are
passed from coreboot via configuration tables. We save these
information into vesa_mode_info structure for future use.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
It looks that x86 chipset always contains a host bridge at pci
b.d.f 0.0.0, so enable this for all boards.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
When running U-Boot bare-metal, the cbfs command is useless.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
|
|
This patch enables NAND support on the Marvell Armada XP
DB-MV784MP-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter Morrow <peter@senient.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
|
Increase max sizes for OOB, Page size and eccpos to
suit for Micron MT29F32G08 part
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
|
|
Update the NAND code to match Linux v4.1. The previous sync was
from Linux v3.15 in commit 4e67c57125290b25.
CONFIG_SYS_NAND_RESET_CNT is removed, as the upstream Linux code now
has its own timeout. Plus, CONFIG_SYS_NAND_RESET_CNT was undocumented
and not selected by any board.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
In addition to mtd_block_isbad(), which checks if a block is bad or
reserved, it's needed to check if a block is reserved only (but not
bad). This commit adds an MTD interface for it, in a similar fashion to
mtd_block_isbad().
While here, fix mtd_block_isbad() so the out-of-bounds checking is done
before the callback check.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[scottwood: Cherry-picked from Linux 8471bb73ba10ed67]
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
I didn't approve the patch that added them. Get them out of the way
before doing a sync.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
This is useful once Andrew's PXA I2C driver gets merged.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
|
|
Add optional LCD support. Note that depending on the toolchain used
one might have to drop some other features to stay within the 0x40000
size limit.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
|
|
Add some more NOR flash details like size, bus width and lock/unlock
time outs.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
|
|
Looks like the define CONFIG_SYS_LCD_PXA_NO_L_BIAS is not used anywhere
else throughout the U-Boot sources any more. Drop it.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
|
|
Conflicts:
configs/socfpga_arria5_defconfig
configs/socfpga_cyclone5_defconfig
configs/socfpga_socrates_defconfig
Merged these by hand and re-ran savedefconfig on them.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
Enable the DWAPB GPIO driver for SoCFPGA Cyclone V and Arria V.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Move config for the E1000 Ethernet driver to Kconfig and tidy up affected
boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Also move the spi flash configurations to the at91-sama5_common.h.
Current at91 zImage size is about 3.3M, the old mapping is not
suitable. So update the spi flash map as following:
0x0 ~ 0x004000: at91bootstrap(16k)
0x04000 ~ 0x008000: u-boot env(16k)
0x08000 ~ 0x060000: u-boot(352k)
0x60000 ~ 0x06c000: dtb (48k)
0x6c000 ~ 0x400000: kernel (3M+592k)
In AT91Bootstrap, the U-Boot in spi flash also update to 0x8000, refer
to following commit in AT91Bootstrap:
3e91e54 Kconfig: fix spi flash address
So also update SPL's u-boot load address to 0x8000 in spi flash.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
As all sama5 nandflash env configurations are same, so move them to
at91-sama5_common.h.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
|
|
Since sama5d3xek boards has different type of dtb blobs, so we need to detect
the cpu type in runtime.
So we add a new variable $dtb_name. if $dtb_name is not defined, we just use
at91-${board_name}.dtb
as the $dtb_name. Otherwise, we will just load the dtb with
$dtb_name.
For sama5d3xek, we will detect cpu type and make up $dtb_name in
runtime.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
|
|
As almost all sama5 sd/mmc env configurations are same, so move them to
at91-sama5_common.h.
Also define CONFIG_ENV_VARS_UBOOT_CONFIG to have the varaible: $board_name.
Then we can use 'at91-${board_name}.dtb' as the dtb name.
TODO: since sama5d3xek has different dtb name, we need to some extra
stuff to make it work on sama5d3xek boards.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
|
|
Bootlog:
U-Boot SPL 2015.10-rc1-00452-g96a7ed1 (Aug 17 2015 - 10:32:21)
mci: setting clock 258000 Hz, block size 512
mci: setting clock 258000 Hz, block size 512
mci: setting clock 258000 Hz, block size 512
mci: setting clock 33024000 Hz, block size 512
reading u-boot.img
reading u-boot.img
U-Boot 2015.10-rc1-00452-g96a7ed1 (Aug 17 2015 - 10:32:21 +0000)
CPU: AT91SAM9G45
Crystal frequency: 12 MHz
CPU clock : 400 MHz
Master clock : 133.333 MHz
Watchdog enabled
DRAM: 256 MiB
WARNING: Caches not enabled
MMC: mci: 0
mci: setting clock 260416 Hz, block size 512
mci: setting clock 260416 Hz, block size 512
mci: setting clock 260416 Hz, block size 512
mci: setting clock 33333333 Hz, block size 512
reading uboot.env
In: serial
Out: serial
Err: serial
Net: macb0
Error: macb0 address not set.
Hit any key to stop autoboot: 0
U-Boot>
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
[add 'picosam9g45_defconfig' to MAINTAINERS]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
The mpddr.c depends on ATMEL_BASE_MPDDRC for the base address to configure the controller.
This cannot be used when there is more than one controller (i.e. AT91SAM9G45, AT91SAM9M10).
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
[remove 'new blank line at EOF']
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Use embedded DTB to let users use u-boot instead of u-boot-dtb.bin.
And fix SPL to use this target.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Added usb dwc3 driver support for zynqmp
this also supports the DFU and LTHOR to download
the linux images on to RAM and cen be booted from
those linux images.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Enable gem0 and setup phy addr for EP.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As we discussed a couple of times, negative CONFIG options make our
life difficult; CONFIG_SYS_NO_FLASH, CONFIG_SYS_DCACHE_OFF, ...
and here is another one.
Now, there are three boards enabling OF_CONTROL on SPL:
- socfpga_arria5_defconfig
- socfpga_cyclone5_defconfig
- socfpga_socrates_defconfig
This commit adds CONFIG_SPL_OF_CONTROL for them and deletes
CONFIG_SPL_DISABLE_OF_CONTROL from the other boards to invert
the logic.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
There is no case where defined(SPL_DISABLE_OF_CONTROL) is true.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
We do not want to compile the DM remove code for SPL. Currently,
we undef it in include/config_uncmd_spl.h (for C files) and in
scripts/Makefile.uncmd_spl (for Makefiles). This is really ugly.
This commit demonstrates how we can deprecate those two files.
Use $(SPL_) for the entry in the Makfile and CONFIG_IS_ENABLED()
in C files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The previous commit introduced a useful macro used in makefiles,
in order to reference to different variables (CONFIG_... or
CONFIG_SPL_...) depending on the build context.
Per-image config option control is a PITA in C sources, too.
Here are some macros useful in C/CPP expressions.
CONFIG_IS_ENABLED(FOO) can be used as a shorthand for
(!defined(CONFIG_SPL_BUILD) && defined(CONFIG_FOO)) || \
(defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_FOO))
For example, it is useful to describe C code as follows,
#if CONFIG_IS_ENABLED(OF_CONTROL)
(device tree code)
#else
(board file code)
#endif
The ifdef conditional above is switched by CONFIG_OF_CONTROL during
the U-Boot proper building (CONFIG_SPL_BUILD is not defined), and by
CONFIG_SPL_OF_CONTROL during SPL building (CONFIG_SPL_BUILD is
defined).
The macro can be used in C context as well, so you can also write the
equivalent code as follows:
if (CONFIG_IS_ENABLED(OF_CONTROL)) {
(device tree code)
} else {
(board file code)
}
Another useful macro is CONFIG_VALUE().
CONFIG_VALUE(FOO) is expanded into CONFIG_FOO if CONFIG_SPL_BUILD is
undefined, and into CONFIG_SPL_FOO if CONFIG_SPL_BUILD is defined.
You can write as follows:
text_base = CONFIG_VALUE(TEXT_BASE);
instead of:
#ifdef CONFIG_SPL_BUILD
text_base = CONFIG_SPL_TEXT_BASE;
#else
text_base = CONFIG_TEXT_BASE;
#endif
This commit also adds slight hacking on fixdep so that it can
output a correct list of fixed dependencies.
If the fixdep finds CONFIG_IS_ENABLED(FOO) in a source file,
we want
$(wildcard include/config/foo.h)
in the U-boot proper building context, while we want
$(wildcard include/config/spl/foo.h)
in the SPL build context.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
A number of LPC32xx SLC NAND defines is dictated by controller
hardware limits and OOB layout is defined by operating system, the
definitions are common for all users. Since those macro are used
in out of NAND SLC driver code (simple NAND SPL framework), they can
not be placed into the driver, therefore move them from board config
files to arch/config.h
The change also adds OOB layout details specific to small page NAND
devices taken from Linux kernel.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
|
|
|
|
|
|
This causes widespread breakage due to the operation of the low-level code
in crt0.S and cro0_64.S for ARM at least.
The fix is not complicated but it seems safer to revert this for now.
This reverts commit 2afddae07523f23f77acd066ad1719f53d289f98.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
