aboutsummaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2020-06-07rockchip: rockpro64: Store default env into SPIMarcin Juszkiewicz
Board has flash chip on board so let store U-Boot environment there. Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07roc-rk3399-pc: Mark default env from SPIJagan Teki
Mark the default U-Boot environment as SPI flash since this is an on board flash device. Updated env offset, size in contrast with default since the U-Boot proper has to start from 384K. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-04Convert CONFIG_BOARD_LATE_INIT to KconfigTom Rini
This converts the following to Kconfig: CONFIG_BOARD_LATE_INIT Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04Convert CONFIG_CMD_ASKENV et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CMD_ASKENV CONFIG_CMD_BMP CONFIG_CMD_BOOTD CONFIG_CMD_CACHE CONFIG_CMD_CRC32 CONFIG_CMD_DHCP CONFIG_CMD_ENV CONFIG_CMD_EXPORTENV CONFIG_CMD_EXT2 CONFIG_CMD_EXT4 CONFIG_CMD_FLASH CONFIG_CMD_FS_GENERIC CONFIG_CMD_FUSE CONFIG_CMD_GPIO CONFIG_CMD_GPT CONFIG_CMD_GREPENV CONFIG_CMD_I2C CONFIG_CMD_IMLS CONFIG_CMD_IMPORTENV CONFIG_CMD_LOADB CONFIG_CMD_LOADS CONFIG_CMD_MEMINFO CONFIG_CMD_MII CONFIG_CMD_MTDPARTS CONFIG_CMD_NAND CONFIG_CMD_NAND_TRIMFFS CONFIG_CMD_NFS CONFIG_CMD_PCA953X CONFIG_CMD_PCA953X_INFO CONFIG_CMD_PCI CONFIG_CMD_PING CONFIG_CMD_READ CONFIG_CMD_SF CONFIG_CMD_SPI CONFIG_CMD_SPL CONFIG_CMD_SPL_WRITE_SIZE CONFIG_CMD_TIME CONFIG_CMD_TRACE CONFIG_CMD_UBI CONFIG_CMD_UBIFS CONFIG_CMD_UNZIP CONFIG_FS_EXT4 Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04Convert CONFIG_BZIP2 et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_BZIP2 CONFIG_GZIP CONFIG_LZO CONFIG_ZLIB CONFIG_LZMA CONFIG_LZO Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04topic_miami: Disable GPIOTom Rini
Per the boards config header file, there is no useful GPIO on these boards. Remove CONFIG_CMD_GPIO from the defconfigs. Cc: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04ARM: rmobile: blanche: Disable CONFIG_CMD_SF / CONFIG_CMD_SPITom Rini
The config header for this platform disables both CMD_SF and CMD_SPI and the defconfig leaves them enabled. Disable them from the defconfig and enable them in the header. Cc: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04bcmstb: Migrate CONFIG_CMD_EXT[24]Tom Rini
The common config header for bcm7260 and bcm7445 enable CONFIG_CMD_EXT2/EXT4 but the defconfigs do not. This results in the commands being disabled. Enable them via the defconfig. Cc: Thomas Fitzsimmons <fitzsim@fitzsim.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04mx6memcal: Finish migration to defconfig optionsTom Rini
The config header for this platform uses '#undef' in a number of cases. All of the MMC related ones were already handled correctly in the defconfig file. In the case of CONFIG_CMD_FUSE, the command was being built and enabled via defconfig. Disable it in the defconfig, cleanup the header. Reviewed-by: Eric Nelson <eric@nelint.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04pfla02: Rework excluding NAND from SPLTom Rini
Rather than only enable CONFIG_CMD_NAND for non-SPL builds, move the CMD options to defconfig and rework the guards to not try and call the function in SPL builds. Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Stefano Babic <sbabic@denx.de>
2020-06-04serial: Convert ARM_DCC to KconfigTom Rini
The symbol "CONFIG_ARM_DCC" is used to control building drivers/serial/arm_dcc.c. Provide a simple Kconfig entry for this. Cc: Luca Ceresoli <luca@lucaceresoli.net> Cc: Michal Simek <monstr@monstr.eu> Cc: Tom McLeod <tom.mcleod@opalkelly.com> Cc: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
2020-06-04Merge https://gitlab.denx.de/u-boot/custodians/u-boot-riscvTom Rini
- Fixes 7e249bc13aaf: ("riscv: Move all SMP related SBI calls to SBI_v01") Move sbi_probe_extension() out of CONFIG_SBI_V01. - SiFive FU540 support SPL.
2020-06-04sifive: fu540: Add sample SD gpt partition layoutJagan Teki
This is a sample GPT partition layout for SD card, right now three important partitions are added to make the system bootable. partition layout: Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000022 0x00000821 "loader1" attrs: 0x0000000000000000 type: 5b193300-fc78-40cd-8002-e86c45580b47 guid: cbcbef44-e627-42bc-b134-93b6f3784b8c 2 0x00000822 0x00002821 "loader2" attrs: 0x0000000000000000 type: 2e54b353-1271-4842-806f-e436d6af6985 guid: f54eba28-d8de-4852-978d-1a673777e2ae 3 0x00002822 0x00020821 "rootfs" attrs: 0x0000000000000004 type: 0fc63daf-8483-4772-8e79-3d69d8477de4 type: linux guid: 9561df46-8d55-4799-a83b-cfee9ef6ff93 Note: - loader1 would be fsbl or spl - loader2 would be U-Boot or U-Boot proper Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
2020-06-04riscv: sifive: fu540: add SPL configurationPragnesh Patel
Add a support for SPL which will boot from L2 LIM (0x0800_0000) and then SPL will boot U-Boot FIT image (OpenSBI FW_DYNAMIC + u-boot.bin) from MMC boot devices. SPL related code is leveraged from FSBL (https://github.com/sifive/freedom-u540-c000-bootloader.git) Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2020-06-03Merge tag 'efi-2020-07-rc4' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for efi-2020-07-rc4 This patch series addresses the following issues: * allow compiling with clang * add missing function descriptions to the HTML documentation * simplify the validation of UEFI images * validate load options in the UEFI boot manager In a preparatory patch a structure definition is moved.
2020-06-03Merge https://gitlab.denx.de/u-boot/custodians/u-boot-spiTom Rini
- Toshiba spinand (Yoshio) - SPI/SPI Flash cleanup (Jagan) - Remove SH SPI (Jagan)
2020-06-03efi_loader: validate load optionHeinrich Schuchardt
For passing the optional data of the load option to the loaded imaged protocol we need its size. efi_deserialize_load_option() is changed to return the size of the optional data. As a by-product we get a partial validation of the load option. Checking the length of the device path remains to be implemented. Some Coverity defects identified the load options as user input because get_unaligned_le32() and get_unaligned_le16() is called. But non of these Coverity defects can be resolved without marking functions with Coverity specific tags. Reported-by: Coverity (CID 303760) Reported-by: Coverity (CID 303768) Reported-by: Coverity (CID 303776) Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-06-02dma-mapping: Add header file for ARCH_DMA_MINALIGNSimon Glass
This is defined in the asm/cache.h header file. Update this header file to include it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
2020-06-01sf: Drop spl_flash_get_sw_write_protJagan Teki
The get_sw_write_prot API is used to get the write-protected bits of flash by reading the status register and other wards it's API for reading register bits. 1) This kind of requirement can be achieved using existing flash operations and flash locking API calls instead of making a separate flash API. 2) Technically there is no real hardware user for this API to use in the source tree. 3) Having a flash operations API for simple register read bits also make difficult to extend the flash operations. 4) Instead of touching generic code, it is possible to have this functionality inside spinor operations in the form of flash hooks or fixups for associated flash chips. Considering all these points, this patch drops the get_sw_write_prot and associated code bases. Cc: Simon Glass <sjg@chromium.org> Cc: Vignesh R <vigneshr@ti.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-05-31rockchip: Add initial support for the Pinebook Pro laptop from Pine64.Peter Robinson
Specification: - Rockchip RK3399 - 4GB Dual-Channel LPDDR4 - eMMC socket - mSD card slot - 128Mbit (16Mb) SPI Flash - AP6256 for 11AC WiFi + BT5 - 14 inch 1920*1080 eDP MiPi display - Camera - USB 3.0, 2.0 ports - Type-C port with alt-mode display (DP 1.2) and 15W charge - DC 5V/3A - optional PCIe slot for NVMe SSD drive Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Tested-by: Vagrant Cascadian <vagrant@debian.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-05-31dt-bindings: input: adopt Linux gpio-keys binding constantsPeter Robinson
Sync the gpio-keys input bindings from linux 5.7-rc1. Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
2020-05-29usb: dwc3: amend UTMI/UTMIW phy interface setupFrank Wang
Let move 8/16-bit UTMI+ interface initialization into DWC3 core init that is convenient for both DM_USB and u-boot traditional process. Signed-off-by: Frank Wang <frank.wang@rock-chips.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-05-29usb: dwc3: Add disable u2mac linestate check quirkJagan Teki
This patch adds a quirk to disable USB 2.0 MAC linestate check during HS transmit. Refer the dwc3 databook, we can use it for some special platforms if the linestate not reflect the expected line state(J) during transmission. When use this quirk, the controller implements a fixed 40-bit TxEndDelay after the packet is given on UTMI and ignores the linestate during the transmit of a token (during token-to-token and token-to-data IPGAP). On some rockchip platforms (e.g. rk3399), it requires to disable the u2mac linestate check to decrease the SSPLIT token to SETUP token inter-packet delay from 566ns to 466ns, and fix the issue that FS/LS devices not recognized if inserted through USB 3.0 HUB. Reference from below Linux commit, commit <65db7a0c9816> ("usb: dwc3: add disable u2mac linestate check quirk") Cc: Marek Vasut <marex@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-05-29usb: dwc3: add dis_u2_freeclk_exists_quirkFrank Wang
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit, which specifies whether the USB2.0 PHY provides a free-running PHY clock, which is active when the clock control input is active. Refer to commit 27f83eeb6b42("usb: dwc3: add dis_u2_freeclk_exists_quirk") in Linux Rockchip Kernel. Signed-off-by: Frank Wang <frank.wang@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2020-05-29usb: dwc3: add dis_enblslpm_quirkFrank Wang
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls whether the PHY receives the suspend signal from the controller. Refer to commit ec791d149bca("usb: dwc3: Add dis_enblslpm_quirk") in Linux Kernel. Signed-off-by: Frank Wang <frank.wang@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2020-05-29rockchip: enable USB OHCI host for RockPro64Marcin Juszkiewicz
U-Boot has video output enabled so time to get keyboard working. => usb reset;usb tree resetting USB... Bus usb@fe380000: USB EHCI 1.00 Bus usb@fe3a0000: USB OHCI 1.0 Bus usb@fe3c0000: USB EHCI 1.00 Bus usb@fe3e0000: USB OHCI 1.0 Bus dwc3: usb maximum-speed not found Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 scanning bus usb@fe380000 for devices... 1 USB Device(s) found scanning bus usb@fe3a0000 for devices... 1 USB Device(s) found scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found scanning bus usb@fe3e0000 for devices... 3 USB Device(s) found scanning bus dwc3 for devices... cannot reset port 1!? 2 USB Device(s) found scanning usb for storage devices... 2 Storage Device(s) found USB device tree: 1 Hub (480 Mb/s, 0mA) u-boot EHCI Host Controller 1 Hub (12 Mb/s, 0mA) U-Boot Root Hub 1 Hub (480 Mb/s, 0mA) u-boot EHCI Host Controller 1 Hub (12 Mb/s, 0mA) | U-Boot Root Hub | +-2 Hub (12 Mb/s, 100mA) | ALCOR Generic USB Hub | +-3 Mass Storage (12 Mb/s, 200mA) Kingston DT 101 G2 001478544887BB3157380157 1 Hub (5 Gb/s, 0mA) | U-Boot XHCI Host Controller | +-2 Mass Storage (5 Gb/s, 76mA) ADATA ADATA USB Flash Drive 1520405012240002 Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-05-29rk3399: Enable NVMe distro bootcmdMark Kettenis
Include NVME in the list of boot targets if CONFIG_NVME is enabled. Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-05-27Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvellTom Rini
- Fix SPI boot on ds414 (Ezra) - Fix PHY mode definition on armada-3720-uDPU (Jakov) - Convert CRS305-1G-4S to generic version (Luka)
2020-05-27cbfs: Don't require the CBFS size with cbfs_init_mem()Simon Glass
The size is not actually used since it is present in the header. Drop this parameter. Also tidy up error handling while we are here. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-05-27cbfs: Allow reading a file from a CBFS given its base addrSimon Glass
Currently we support reading a file from CBFS given the address of the end of the ROM. Sometimes we only know the start of the CBFS. Add a function to find a file given that. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-05-27cbfs: Change file_cbfs_find_uncached() to return an errorSimon Glass
This function currently returns a node pointer so there is no way to know the error code. Also it uses data in BSS which seems unnecessary since the caller might prefer to use a local variable. Update the function and split its body out into a separate function so we can use it later. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-05-27cbfs: Return the error code from file_cbfs_init()Simon Glass
We may as well return the error code and use it directly in the command code. CBFS still uses its own error enum which we may be able to remove, but leave it for now. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-05-27cbfs: Use ulong consistentlySimon Glass
U-Boot uses ulong for addresses but there are a few places in this driver that don't use it. Convert this driver over to follow this convention fully. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-05-27cbfs: drop file_cbfs_result declarationChristian Gmeiner
It is not definded anywhere. Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-by: Heinrich Schuchardt <xypron.gpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-05-27arm: mvebu: Convert CRS305-1G-4S board to CRS3xx-98DX3236Luka Kovacic
Convert the CRS305-1G-4S board to CRS3xx-98DX3236 to enable easier implementation of new CRS3xx series boards, based on Marvell Prestera 98DX3236. Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr> Reviewed-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Jakov Petrina <jakov.petrina@sartura.hr>
2020-05-27arm: mvebu: ds414: define CONFIG_SYS_U_BOOT_OFFSEzra Buehler
Without CONFIG_SYS_U_BOOT_OFFS set to CONFIG_SYS_SPI_U_BOOT_OFFS, U-Boot will be located at address 0x16000. But, SPL will try to load the payload from 0x24000 causing the boot to hang. Signed-off-by: Ezra Buehler <ezra@easyb.ch> Reviewed-by: Stefan Roese <sr@denx.de>
2020-05-25sandbox: move compression option to KconfigMichael Walle
CONFIG_BZIP2 and CONFIG_GZIP_COMPRESSED are Kconfig options. Select them by CONFIG_SANDBOX instead of setting them in configs/sandbox.h. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-05-25Convert CONFIG_CMD_MMC to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CMD_MMC Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-25doc: dfu: describe more DFU functionHeinrich Schuchardt
Add some of the missing DFU function descriptions. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: Lukasz Majewski <lukma@denx.de>
2020-05-25doc: dfu: add DFU to HTML documentationHeinrich Schuchardt
Add the device firmware update functions to the generated HTML documentation. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: Lukasz Majewski <lukma@denx.de>
2020-05-22Merge branch 'net' of git://git.denx.de/u-boot-socfpgaTom Rini
- ks8851 cleanups and DM migration
2020-05-22net: ks8851: Add Kconfig entriesMarek Vasut
Convert CONFIG_KS8851_MLL and CONFIG_KS8851_MLL_BASEADDR to Kconfig Signed-off-by: Marek Vasut <marex@denx.de> Cc: Eugen Hristev <eugen.hristev@microchip.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-05-22Merge tag 'u-boot-rockchip-20200522' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Fix rk3288 chromebook veyron support; - Add pcie driver support for rk3399; - other fixes for rk3399 boards
2020-05-22Merge tag 'efi-2020-07-rc3-2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for efi-2020-07-rc3 (2) Problems fixed with these patches are: * UEFI sub-system not working with virtio block devices * Missing SATA support in UEFI sub-system * A superfluous debug statement
2020-05-22rockpro64: Enable HDMI output on rockpro64 boardAndrius Štikonas
Reference to commit that adds HDMI to other rk3399 boards: commit 9778edae5576 ("rockchip: Enable HDMI output on rk3399 board w/ HDMI") Signed-off-by: Andrius Štikonas <andrius@stikonas.eu> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Kever Yang <kever.yang@rock-chips.com> Tested-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-05-21Merge git://git.denx.de/u-boot-shTom Rini
- Enable -ffunction-sections / -fdata-sections --gc-sections to SH - RCar Gen3 updates
2020-05-21efi_loader: device path for SATA devicesHeinrich Schuchardt
Provide device path nodes for SATA devices. This avoids creation of two handles with the same device path indicating our root node. This is what the device paths for a SATA drive with four partitions could like: /VenHw(..)/Sata(0x0,0xffff,0x0) /VenHw(..)/Sata(0x0,0xffff,0x0)/HD(1,MBR,0x81ea591f,0x800,0x63ff830) /VenHw(..)/Sata(0x0,0xffff,0x0)/HD(2,MBR,0x81ea591f,0x6400800,0x9ff830) /VenHw(..)/Sata(0x0,0xffff,0x0)/HD(3,MBR,0x81ea591f,0x6e00800,0x16ef2ab0) /VenHw(..)/Sata(0x0,0xffff,0x0)/HD(4,MBR,0x81ea591f,0x1dcf3800,0x1dcedab0) Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-05-21efi_loader: device path for virtio block devicesHeinrich Schuchardt
The UEFI specification does not define a device sub-type for virtio. Let's use a vendor hardware node here. This avoids creation of two handles with the same device path indicating our root node. Reported-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-05-21efi_loader: add EFI_MEMORY_SP to memory attributesHeinrich Schuchardt
The UEFI 2.8 specification has introduced the EFI_MEMORY_SP memory attribute. Add it to the 'efidebug memmap' and 'efi mem' commands. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-05-20Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini
- Add DM_ETH support for lx2160aqds, ls2080aqds, ls1088aqds - QSI related fixes on ls1012a, ls2080a, ls1046a, ls1088a, ls1043a based platforms - Bug-fixes/updtaes related to ls1046afrwy, fsl-mc, msi-map property
generated by cgit v1.2.3 (git 2.39.1) at 2024-09-21 11:28:00 +0000