| Age | Commit message (Collapse) | Author |
|---|
|
This type of bus is used in Linux to designate buses which have power
domains and/or clocks which need to be enabled before their child devices
can be used. Because power domains are automatically enabled before probing
in U-Boot, we just need to enable any clocks present.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This pll code is primarily based on the code from the kendryte standalone
sdk in lib/drivers/sysctl.c. k210_pll_calc_config is roughly analogous to
the algorithm used to set the pll frequency, but it has been completely
rewritten to be fixed-point based.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
CC: Lukasz Majewski <lukma@denx.de>
|
|
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.
Before this change it was necessary to use:
/* SPI Flash Configs */
#if defined(CONFIG_SPL_BUILD)
#undef CONFIG_DM_SPI
#undef CONFIG_DM_SPI_FLASH
#undef CONFIG_SPI_FLASH_MTD
#endif
in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.
The goal of this patch:
Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.
Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).
In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):
- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
environment with no fitImage and OF_LIBFDT support).
Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.
This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
If there are aliases for an uclass, set the base for the "dynamically"
allocated numbers next to the highest alias.
Please note, that this might lead to holes in the sequences, depending
on the device tree. For example if there is only an alias "ethernet1",
the next device seq number would be 2.
In particular this fixes a problem with boards which are using ethernet
aliases but also might have network add-in cards like the E1000. If the
board is started with the add-in card and depending on the order of the
drivers, the E1000 might occupy the first ethernet device and mess up
all the hardware addresses, because the devices are now shifted by one.
Also adapt the test cases to the new handling and add test cases
checking the holes in the seq numbers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Alex Marginean <alexandru.marginean@nxp.com>
Tested-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Michal Simek <michal.simek@xilinx.com> [on zcu102-revA]
|
|
It is possible to specify a device tree node for an USB device. This is
useful if you have a static USB setup and want to use aliases which
point to these nodes, like on the Raspberry Pi.
The nodes are matched against their hub port number, the compatible
strings are not matched for now.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The get_sw_write_prot API is used to get the write-protected
bits of flash by reading the status register and other wards
it's API for reading register bits.
1) This kind of requirement can be achieved using existing
flash operations and flash locking API calls instead of
making a separate flash API.
2) Technically there is no real hardware user for this API to
use in the source tree.
3) Having a flash operations API for simple register read bits
also make difficult to extend the flash operations.
4) Instead of touching generic code, it is possible to have
this functionality inside spinor operations in the form of
flash hooks or fixups for associated flash chips.
Considering all these points, this patch drops the get_sw_write_prot
and associated code bases.
Cc: Simon Glass <sjg@chromium.org>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Quite a few tests still use ut_assertok(memcmp(...)) and variants. Modify
them to use the macro designed for this purpose.
Suggested-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
|
|
Move this header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- Enable USB Host for Odroid-C2 board
- Add Open-Drain/Open-Source emulation in GPIO uclass
|
|
Add tests for testing open-drain/open-source emulation in gpio-uclass.
It also adds two test3-gpios configured as GPIO_ACTIVE_LOW.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
Add test whether the CPU is U-Boot is running from.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add a test item for the phy_bulk API
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add a test item for ofnode_get_child_count()
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
It is useful to dump ACPI tables in U-Boot to see what has been generated.
Add a command to handle this.
To allow the command to find the tables, add a position into the global
data.
Support subcommands to list and dump the tables.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
|
|
Put this in the context along with the other important pointers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
|
|
We always write three basic tables to ACPI at the start. Move this into
its own function, along with acpi_fill_header(), so we can write a test
for this code.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this code to a generic location so that we can test it with sandbox.
This requires adding a few new fields to acpi_ctx, so drop the local
variables used in the original code.
Also use mapmem to avoid pointer-to-address casts which don't work on
sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
|
|
The current code uses an address but a pointer would result in fewer
casts. Also it repeats the alignment code in a lot of places so this would
be better done in a helper function.
Update write_acpi_tables() to make use of the new acpi_ctx structure,
adding a few helpers to clean things up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
|
|
A device may want to write out ACPI tables to describe itself to Linux.
Add a method to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
|
|
Add tests for new API set_dir_flags and set_dir_flags and associated
code in gpio uclass.
Test support for new flags GPIO_OPEN_DRAIN, GPIO_OPEN_SOURCE
GPIO_PULL_UP and GPIO_PULL_DOWN.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
This patch removes the ops get_open_drain/set_open_drain
and the API dm_gpio_get_open_drain/dm_gpio_set_open_drain.
The ops only provided in one driver (mpc8xxx gpio) and the
associated API is never called in boards.
This patch prepare a more generic set/get_dir_flags ops,
including the open drain property.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add functions to iterate on all property with livetree
- dev_read_first_prop
- dev_read_next_prop
- dev_read_prop_by_prop
and
- ofnode_get_first_property
- ofnode_get_next_property
- ofnode_get_property_by_prop
And helper: dev_for_each_property
For example:
struct ofprop property;
dev_for_each_property(property, config) {
value = dev_read_prop_by_prop(&property, &propname, &len);
or:
for (res = ofnode_get_first_property(node, &property);
!res;
res = ofnode_get_next_property(&property))
{
value = ofnode_get_property_by_prop(&property, &propname, &len);
....
}
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Functions for reading indexed values from device tree
Enhancements to 'dm' command
Log test enhancements and syslog driver
DM change to read parent ofdata before children
Minor fixes
|
|
At present a device can read its ofdata before its parent has done the
same. This can cause problems in the case where the parent has a 'ranges'
property, thus affecting the operation of dev_read_addr(), for example.
We already probe parent devices before children so it does not seem to be
a large step to do the same with ofdata.
Make the change and update the documentation in this area.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Add a new test for fdtdec_set_carveout().
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drop blank line at EFO:
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The patch adds helper functions to allow reading a single indexed u32
value from a device-tree property containing multiple u32 values, that
is an array of integers.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add test case to cover dev_read_u64 and dev_read_u64_default functions.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Use the new function dm_scan_fdt_ofnode_path() to scan all the nodes
which aren't devices themselves but may contain some:
- "/chosen"
- "/clocks"
- "/firmware"
The patch removes the strcmp call in recursive function dm_scan_fdt_live()
and also corrects a conflict with the 2 applied patches in
the commit 1712ca21924b ("dm: core: Scan /firmware node by default")
and in the commit 747558d01457 ("dm: fdt: scan for devices under
/firmware too"): the subnodes of "/firmware" (optee for example)
are bound 2 times.
For example the dm tree command result on STM32MP1 is:
STM32MP> dm tree
Class Index Probed Driver Name
-----------------------------------------------------------
root 0 [ + ] root_driver root_driver
firmware 0 [ ] psci |-- psci
sysreset 0 [ ] psci-sysreset | `-- psci-sysreset
simple_bus 0 [ + ] generic_simple_bus |-- soc
...
tee 0 [ + ] optee |-- optee
...
tee 1 [ ] optee `-- optee
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The DMA Remapping Reporting (DMAR) table contains information about DMA
remapping.
Add a version simple version of this table with only the minimum fields
filled out. i.e. no entries.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
|
|
Each ACPI table has its own version number. Add the version numbers in a
single function so we can keep them consistent and easily see what
versions are supported.
Start a new acpi_table file in a generic directory to house this function.
We can move things over to this file from x86 as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add a sandbox test for the basic ACPI functionality we have so far.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
|
|
Different CPUs may support different address widths, meaning the amount of
memory they can address. Add a property for this to the cpu_info struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Some callers of serial_getinfo() would like to know the UART base
clock speed in order to make decision what to pass to OS in some
cases. In particular, ACPI SPCR table expects only certain base
clock speed and thus we have to act accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
|
|
At present driver model supports the IRQ uclass but there is no way to
request a particular interrupt for a driver.
Add a mechanism, similar to clock and reset, to read the interrupts
required by a device from the device tree and to request those interrupts.
U-Boot itself does not have interrupt-driven handlers, so just provide a
means to read and clear an interrupt. This can be useful to handle
peripherals which must use an interrupt to determine when data is
available, for example.
Bring over the basic binding file as well, from Linux v5.4. Note that the
older binding is not supported in U-Boot; the newer 'special form' must be
used.
Add a simple test of the new functionality.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
There can be different types of interrupt controllers in a system and some
drivers may need to distinguish between these. In general this can be
handled using the device tree by adding the interrupt information to
device nodes.
However on x86 devices we have interrupt controllers which are not tied
to any particular device and not really used in U-Boot. These still need
to be inited, so a convenient method is to give each controller a type
and allow a particular controller type to be probed.
Add support for this in sandbox along with a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove the new bland line at EOF of test/dm/irq.c]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
It is sometimes useful to find a device in a uclass using only its driver
data. The driver data often indicates the 'subtype' of the device, e,g,
via its compatible string.
Add a function to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present we have uclass_foreach_dev() which requires that uclass_get()
be called beforehand to find the uclass. This is good if we suspect that
that function might fail, but often we know that the uclass is available.
Add a new helper which does this uclass_get() automatically, so that only
the uclass ID is needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
|
At present there is no positive indication that U-Boot has finished
sending sound data. This means that it is not possible to power down an
audio codec, for example. Add a new method that is called once all sound
data has been sent.
Add a new method for this, called when the sound_play() call is done.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present we reset the console buffer before each test but do not
actually set the recording flag. Without this, the output is not
recorded.
Update the code to set the flag before the test and clear it afterwards.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
It is sometimes useful to process all children, making sure they are
probed first. Add functions to help with this and a macro to make it more
convenient.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
When generating ACPI tables we need to make sure that all devices have
read their platform data, so that they can generate the tables correctly.
Rather than adding this code in ACPI, create a core function to handle it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add a function to read a property from the chosen node, providing access
to its length. Update ofnode_get_chosen_string() to make use of it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add a new function to read a property that supports reading the length as
well.
Reimplement ofnode_read_string() using it and fix its comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This function is actually intended to read a string rather than a
property. All of its current callers use it that way. Also there is no way
to return the length of the property from this function.
Rename it to better indicate its purpose, using ofnode_read as the prefix
since this matches most other functions.
Also add some tests which are missing for these functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
