From 76a472dc4408b58c8b4022a6962ef3e34015005f Mon Sep 17 00:00:00 2001 From: Heinrich Schuchardt Date: Sun, 29 Jul 2018 13:50:50 +0200 Subject: doc: README.iscsi: make compatible with restructured text The Sphinx documentation system uses restructured text. Make the README.iscsi file compatible. Signed-off-by: Heinrich Schuchardt --- doc/README.iscsi | 130 +++++++++++++++++++++++++++++-------------------------- 1 file changed, 68 insertions(+), 62 deletions(-) diff --git a/doc/README.iscsi b/doc/README.iscsi index cb71c6e7446..faee6362642 100644 --- a/doc/README.iscsi +++ b/doc/README.iscsi @@ -1,6 +1,8 @@ -# iSCSI booting with U-Boot and iPXE +iSCSI booting with U-Boot and iPXE +================================== -## Motivation +Motivation +---------- U-Boot has only a reduced set of supported network protocols. The focus for network booting has been on UDP based protocols. A TCP stack and HTTP support @@ -32,14 +34,15 @@ via HTTPS and to download any other files needed for booting via iSCSI from the same target where the operating system is installed. An alternative to implementing these protocols in U-Boot is to use an existing -software that can run on top of U-Boot. iPXE is the "swiss army knife" of +software that can run on top of U-Boot. iPXE[1] is the "swiss army knife" of network booting. It supports both HTTPS and iSCSI. It has a scripting engine for fine grained control of the boot process and can provide a command shell. iPXE can be built as an EFI application (named snp.efi) which can be loaded and run by U-Boot. -## Boot sequence +Boot sequence +------------- U-Boot loads the EFI application iPXE snp.efi using the bootefi command. This application has network access via the simple network protocol offered by @@ -56,67 +59,68 @@ For a selected iSCSI target iPXE sets up a handle with the block IO protocol. It uses the ConnectController boot service of U-Boot to request U-Boot to connect a file system driver. U-Boot reads from the iSCSI drive via the block IO protocol offered by iPXE. It creates the partition handles and installs the simple file -protocol. Now iPXE can call the simple file protocol to load Grub. U-Boot uses -the block IO protocol offered by iPXE to fulfill the request. - -Once Grub is started it uses the same block IO protocol to load Linux. Via -the EFI stub Linux is called as an EFI application. - -``` - +--------+ +--------+ - | | Runs | | - | U-Boot |=========>| iPXE | - | EFI | | snp.efi| -+--------+ | | DHCP | | -| |<====|********|<=========| | -| DHCP | | | Get IP | | -| Server | | | Address | | -| |====>|********|=========>| | -+--------+ | | Response | | - | | | | - | | | | -+--------+ | | HTTPS | | -| |<====|********|<=========| | -| HTTPS | | | Load | | -| Server | | | Script | | -| |====>|********|=========>| | -+--------+ | | | | - | | | | - | | | | -+--------+ | | iSCSI | | -| |<====|********|<=========| | -| iSCSI | | | Auth | | -| Server |====>|********|=========>| | -| | | | | | -| | | | Loads | | -| |<====|********|<=========| | +--------+ -| | | | Grub | | Runs | | -| |====>|********|=========>| |=======>| Grub | -| | | | | | | | -| | | | | | | | -| | | | | | Loads | | -| |<====|********|<=========|********|<=======| | +--------+ -| | | | | | Linux | | Runs | | -| |====>|********|=========>|********|=======>| |=====>| Linux | -| | | | | | | | | | -+--------+ +--------+ +--------+ +--------+ | | - | | - | | - | ~ ~ ~ ~| -``` - -## Security +protocol. Now iPXE can call the simple file protocol to load GRUB[2]. U-Boot +uses the block IO protocol offered by iPXE to fulfill the request. + +Once GRUB is started it uses the same block IO protocol to load Linux. Via +the EFI stub Linux is called as an EFI application:: + + +--------+ +--------+ + | | Runs | | + | U-Boot |========>| iPXE | + | EFI | | snp.efi| + +--------+ | | DHCP | | + | |<===|********|<========| | + | DHCP | | | Get IP | | + | Server | | | Address | | + | |===>|********|========>| | + +--------+ | | Response| | + | | | | + | | | | + +--------+ | | HTTPS | | + | |<===|********|<========| | + | HTTPS | | | Load | | + | Server | | | Script | | + | |===>|********|========>| | + +--------+ | | | | + | | | | + | | | | + +--------+ | | iSCSI | | + | |<===|********|<========| | + | iSCSI | | | Auth | | + | Server |===>|********|========>| | + | | | | | | + | | | | Loads | | + | |<===|********|<========| | +--------+ + | | | | GRUB | | Runs | | + | |===>|********|========>| |======>| GRUB | + | | | | | | | | + | | | | | | | | + | | | | | | Loads | | + | |<===|********|<========|********|<======| | +--------+ + | | | | | | Linux | | Runs | | + | |===>|********|========>|********|======>| |=====>| Linux | + | | | | | | | | | | + +--------+ +--------+ +--------+ +--------+ | | + | | + | | + | ~ ~ ~ ~| + +Security +-------- The iSCSI protocol is not encrypted. The traffic could be secured using IPsec but neither U-Boot nor iPXE does support this. So we should at least separate the iSCSI traffic from all other network traffic. This can be achieved using a virtual local area network (VLAN). -## Configuration +Configuration +------------- -### iPXE +iPXE +^^^^ -For running iPXE on arm64 the bin-arm64-efi/snp.efi build target is needed. +For running iPXE on arm64 the bin-arm64-efi/snp.efi build target is needed:: git clone http://git.ipxe.org/ipxe.git cd ipxe/src @@ -132,7 +136,7 @@ http://ipxe.org/cfg iPXE by default will put the CPU to rest when waiting for input. U-Boot does not wake it up due to missing interrupt support. To avoid this behavior create -file src/config/local/nap.h. +file src/config/local/nap.h:: /* nap.h */ #undef NAP_EFIX86 @@ -140,7 +144,7 @@ file src/config/local/nap.h. #define NAP_NULL The supported commands in iPXE are controlled by an include, too. Putting the -following into src/config/local/general.h is sufficient for most use cases. +following into src/config/local/general.h is sufficient for most use cases:: /* general.h */ #define NSLOOKUP_CMD /* Name resolution command */ @@ -153,7 +157,9 @@ following into src/config/local/general.h is sufficient for most use cases. #define DOWNLOAD_PROTO_NFS /* Network File System Protocol */ #define DOWNLOAD_PROTO_FILE /* Local file system access */ -## Links +Links +----- -* https://ipxe.org - iPXE open source boot firmware -* https://www.gnu.org/software/grub/ - GNU Grub (Grand Unified Bootloader) +* [1](https://ipxe.org) https://ipxe.org - iPXE open source boot firmware +* [2](https://www.gnu.org/software/grub/) https://www.gnu.org/software/grub/ - + GNU GRUB (Grand Unified Bootloader) -- cgit v1.2.3