From e25d5a95e7ff45b18e3d9dfac24efd35377abf53 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Thu, 10 Dec 2015 10:32:36 +0100 Subject: arm: mvebu: Make serdes setup on Armada XP less noisy Change some of the PEX configuration output lines from always output to only ouput upon specific debug enabling. This changes the SPL output from: U-Boot SPL 2016.01-rc2-00037-g9353a7f (Dec 10 2015 - 10:27:42) High speed PHY - Version: 2.1.5 (COM-PHY-V20) Update Device ID PEX0782611ab Update Device ID PEX1782611ab Update Device ID PEX2782611ab Update Device ID PEX3782611ab Update Device ID PEX8782611ab Update PEX Device ID 0x78260 High speed PHY - Ended Successfully DDR3 Training Sequence - Ver 5.7.4 DDR3 Training Sequence - Ended Successfully to: U-Boot SPL 2016.01-rc2-00037-g9353a7f-dirty (Dec 10 2015 - 10:32:04) High speed PHY - Version: 2.1.5 (COM-PHY-V20) High speed PHY - Ended Successfully DDR3 Training Sequence - Ver 5.7.4 DDR3 Training Sequence - Ended Successfully Resulting in a little faster bootup time. Signed-off-by: Stefan Roese Cc: Luka Perkov --- arch/arm/mach-mvebu/serdes/axp/high_speed_env_lib.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-mvebu/serdes/axp/high_speed_env_lib.c b/arch/arm/mach-mvebu/serdes/axp/high_speed_env_lib.c index 976297119f5..bfa7f136c34 100644 --- a/arch/arm/mach-mvebu/serdes/axp/high_speed_env_lib.c +++ b/arch/arm/mach-mvebu/serdes/axp/high_speed_env_lib.c @@ -1376,19 +1376,19 @@ int serdes_phy_config(void) pex_if, PEX_DEVICE_AND_VENDOR_ID)); devId &= 0xFFFF; devId |= ((ctrl_mode << 16) & 0xffff0000); - DEBUG_INIT_S("Update Device ID PEX"); - DEBUG_INIT_D(pex_if, 1); - DEBUG_INIT_D(devId, 8); - DEBUG_INIT_S("\n"); + DEBUG_INIT_FULL_S("Update Device ID PEX"); + DEBUG_INIT_FULL_D(pex_if, 1); + DEBUG_INIT_FULL_D(devId, 8); + DEBUG_INIT_FULL_S("\n"); reg_write(PEX_CFG_DIRECT_ACCESS (pex_if, PEX_DEVICE_AND_VENDOR_ID), devId); if ((pex_if < 8) && (info->pex_mode[pex_unit] == PEX_BUS_MODE_X4)) pex_if += 3; } - DEBUG_INIT_S("Update PEX Device ID 0x"); - DEBUG_INIT_D(ctrl_mode, 4); - DEBUG_INIT_S("0\n"); + DEBUG_INIT_FULL_S("Update PEX Device ID 0x"); + DEBUG_INIT_FULL_D(ctrl_mode, 4); + DEBUG_INIT_FULL_S("0\n"); } tmp = reg_read(PEX_DBG_STATUS_REG(0)); DEBUG_RD_REG(PEX_DBG_STATUS_REG(0), tmp); -- cgit v1.2.3