From 8fe280f330ddfd4a9e395ca15ab4019a1a32aa1f Mon Sep 17 00:00:00 2001
From: Ye.Li
Date: Thu, 30 Oct 2014 18:53:49 +0800
Subject: imx: mx6 sabreauto: Add board support for USB EHCI

On mx6 sabreauto board, there are two USB ports:
0: OTG
1: HOST
The EHCI driver is enabled for this board, but the IOMUX and VBUS power
control is not implemented, which cause both USB port failed to work.
This patch fix the problem by adding the board support codes.

Since the power control uses the GPIO pin from port expander MAX7310,
the PCA953X driver is enabled for accessing the MAX7310.

The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting
its daisy chain. Add a new function "imx_iomux_set_gpr_register" to
handle GPR register setting.

Signed-off-by: Ye.Li <B37916@freescale.com>
---
 board/freescale/mx6qsabreauto/mx6qsabreauto.c | 93 +++++++++++++++++++++++++++
 1 file changed, 93 insertions(+)

(limited to 'board/freescale')

diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
index 0dc0160e19f..42ae6fac5e2 100644
--- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c
+++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
@@ -27,6 +27,7 @@
 #include <asm/arch/mxc_hdmi.h>
 #include <asm/imx-common/video.h>
 #include <asm/arch/crm_regs.h>
+#include <pca953x.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -116,6 +117,44 @@ static iomux_v3_cfg_t const port_exp[] = {
 	MX6_PAD_SD2_DAT0__GPIO1_IO15		| MUX_PAD_CTRL(NO_PAD_CTRL),
 };
 
+/*Define for building port exp gpio, pin starts from 0*/
+#define PORTEXP_IO_NR(chip, pin) \
+	((chip << 5) + pin)
+
+/*Get the chip addr from a ioexp gpio*/
+#define PORTEXP_IO_TO_CHIP(gpio_nr) \
+	(gpio_nr >> 5)
+
+/*Get the pin number from a ioexp gpio*/
+#define PORTEXP_IO_TO_PIN(gpio_nr) \
+	(gpio_nr & 0x1f)
+
+static int port_exp_direction_output(unsigned gpio, int value)
+{
+	int ret;
+
+	i2c_set_bus_num(2);
+	ret = i2c_probe(PORTEXP_IO_TO_CHIP(gpio));
+	if (ret)
+		return ret;
+
+	ret = pca953x_set_dir(PORTEXP_IO_TO_CHIP(gpio),
+		(1 << PORTEXP_IO_TO_PIN(gpio)),
+		(PCA953X_DIR_OUT << PORTEXP_IO_TO_PIN(gpio)));
+
+	if (ret)
+		return ret;
+
+	ret = pca953x_set_val(PORTEXP_IO_TO_CHIP(gpio),
+		(1 << PORTEXP_IO_TO_PIN(gpio)),
+		(value << PORTEXP_IO_TO_PIN(gpio)));
+
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
 static void setup_iomux_enet(void)
 {
 	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
@@ -361,3 +400,57 @@ int checkboard(void)
 
 	return 0;
 }
+
+#ifdef CONFIG_USB_EHCI_MX6
+#define USB_HOST1_PWR     PORTEXP_IO_NR(0x32, 7)
+#define USB_OTG_PWR       PORTEXP_IO_NR(0x34, 1)
+
+iomux_v3_cfg_t const usb_otg_pads[] = {
+	MX6_PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+int board_ehci_hcd_init(int port)
+{
+	switch (port) {
+	case 0:
+		imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
+			ARRAY_SIZE(usb_otg_pads));
+
+		/*
+		  * Set daisy chain for otg_pin_id on 6q.
+		 *  For 6dl, this bit is reserved.
+		 */
+		imx_iomux_set_gpr_register(1, 13, 1, 0);
+		break;
+	case 1:
+		break;
+	default:
+		printf("MXC USB port %d not yet supported\n", port);
+		return -EINVAL;
+	}
+	return 0;
+}
+
+int board_ehci_power(int port, int on)
+{
+	switch (port) {
+	case 0:
+		if (on)
+			port_exp_direction_output(USB_OTG_PWR, 1);
+		else
+			port_exp_direction_output(USB_OTG_PWR, 0);
+		break;
+	case 1:
+		if (on)
+			port_exp_direction_output(USB_HOST1_PWR, 1);
+		else
+			port_exp_direction_output(USB_HOST1_PWR, 0);
+		break;
+	default:
+		printf("MXC USB port %d not yet supported\n", port);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+#endif
-- 
cgit v1.2.3