From cfa460adfdefcc30d104e1a9ee44994ee349bb7b Mon Sep 17 00:00:00 2001 From: William Juul Date: Wed, 31 Oct 2007 13:53:06 +0100 Subject: Update MTD to that of Linux 2.6.22.1 A lot changed in the Linux MTD code, since it was last ported from Linux to U-Boot. This patch takes U-Boot NAND support to the level of Linux 2.6.22.1 and will enable support for very large NAND devices (4KB pages) and ease the compatibility between U-Boot and Linux filesystems. This patch is tested on two custom boards with PPC and ARM processors running YAFFS in U-Boot and Linux using gcc-4.1.2 cross compilers. MAKEALL ppc/arm has some issues: * DOC/OneNand/nand_spl is not building (I have not tried porting these parts, and since I do not have any HW and I am not familiar with this code/HW I think its best left to someone else.) Except for the issues mentioned above, I have ported all drivers necessary to run MAKEALL ppc/arm without errors and warnings. Many drivers were trivial to port, but some were not so trivial. The following drivers must be examined carefully and maybe rewritten to some degree: cpu/ppc4xx/ndfc.c cpu/arm926ejs/davinci/nand.c board/delta/nand.c board/zylonite/nand.c Signed-off-by: William Juul Signed-off-by: Stig Olsen Signed-off-by: Scott Wood --- board/prodrive/pdnb3/nand.c | 53 +++++++++++++++------------------------------ 1 file changed, 18 insertions(+), 35 deletions(-) (limited to 'board/prodrive/pdnb3') diff --git a/board/prodrive/pdnb3/nand.c b/board/prodrive/pdnb3/nand.c index b1e7041046f..281ae70af61 100644 --- a/board/prodrive/pdnb3/nand.c +++ b/board/prodrive/pdnb3/nand.c @@ -52,40 +52,26 @@ static struct pdnb3_ndfc_regs *pdnb3_ndfc; * * There is one NAND devices on the board, a Hynix HY27US08561A (32 MByte). */ -static void pdnb3_nand_hwcontrol(struct mtd_info *mtd, int cmd) +static void pdnb3_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { - switch (cmd) { - case NAND_CTL_SETCLE: - hwctl |= 0x1; - break; - case NAND_CTL_CLRCLE: - hwctl &= ~0x1; - break; - - case NAND_CTL_SETALE: - hwctl |= 0x2; - break; - case NAND_CTL_CLRALE: - hwctl &= ~0x2; - break; - - case NAND_CTL_SETNCE: - break; - case NAND_CTL_CLRNCE: - writeb(0x00, &(pdnb3_ndfc->term)); - break; + struct nand_chip *this = mtd->priv; + + if (ctrl & NAND_CTRL_CHANGE) { + if ( ctrl & NAND_CLE ) + hwctl |= 0x1; + else + hwctl &= ~0x1; + if ( ctrl & NAND_ALE ) + hwctl |= 0x2; + else + hwctl &= ~0x2; + if ( (ctrl & NAND_NCE) != NAND_NCE) + writeb(0x00, &(pdnb3_ndfc->term)); } + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); } -static void pdnb3_nand_write_byte(struct mtd_info *mtd, u_char byte) -{ - if (hwctl & 0x1) - writeb(byte, &(pdnb3_ndfc->cmd)); - else if (hwctl & 0x2) - writeb(byte, &(pdnb3_ndfc->addr)); - else - writeb(byte, &(pdnb3_ndfc->data)); -} static u_char pdnb3_nand_read_byte(struct mtd_info *mtd) { @@ -152,16 +138,13 @@ int board_nand_init(struct nand_chip *nand) { pdnb3_ndfc = (struct pdnb3_ndfc_regs *)CFG_NAND_BASE; - nand->eccmode = NAND_ECC_SOFT; + nand->ecc.mode = NAND_ECC_SOFT; /* Set address of NAND IO lines (Using Linear Data Access Region) */ nand->IO_ADDR_R = (void __iomem *) ((ulong) pdnb3_ndfc + 0x4); nand->IO_ADDR_W = (void __iomem *) ((ulong) pdnb3_ndfc + 0x4); /* Reference hardware control function */ - nand->hwcontrol = pdnb3_nand_hwcontrol; - /* Set command delay time */ - nand->hwcontrol = pdnb3_nand_hwcontrol; - nand->write_byte = pdnb3_nand_write_byte; + nand->cmd_ctrl = pdnb3_nand_hwcontrol; nand->read_byte = pdnb3_nand_read_byte; nand->write_buf = pdnb3_nand_write_buf; nand->read_buf = pdnb3_nand_read_buf; -- cgit v1.2.3