.. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause .. sectionauthor:: Udit Kumar J7200 Platforms =============== Introduction: ------------- The J7200 family of SoCs are part of K3 Multicore SoC architecture platform targeting automotive applications. They are designed as a low power, high performance and highly integrated device architecture, adding significant enhancement on processing power, graphics capability, video and imaging processing, virtualization and coherent memory support. The device is partitioned into three functional domains, each containing specific processing cores and peripherals: 1. Wake-up (WKUP) domain: * Device Management and Security Controller (DMSC) 2. Microcontroller (MCU) domain: * Dual Core ARM Cortex-R5F processor 3. MAIN domain: * Dual core 64-bit ARM Cortex-A72 More info can be found in TRM: https://www.ti.com/lit/pdf/spruiu1 Platform information: * https://www.ti.com/tool/J7200XSOMXEVM Boot Flow: ---------- Below is the pictorial representation of boot flow: .. image:: img/boot_diagram_k3_current.svg - Here DMSC acts as master and provides all the critical services. R5/A72 requests DMSC to get these services done as shown in the above diagram. Sources: -------- .. include:: k3.rst :start-after: .. k3_rst_include_start_boot_sources :end-before: .. k3_rst_include_end_boot_sources Build procedure: ---------------- 0. Setup the environment variables: .. include:: k3.rst :start-after: .. k3_rst_include_start_common_env_vars_desc :end-before: .. k3_rst_include_end_common_env_vars_desc .. include:: k3.rst :start-after: .. k3_rst_include_start_board_env_vars_desc :end-before: .. k3_rst_include_end_board_env_vars_desc Set the variables corresponding to this platform: .. include:: k3.rst :start-after: .. k3_rst_include_start_common_env_vars_defn :end-before: .. k3_rst_include_end_common_env_vars_defn .. code-block:: bash $ export UBOOT_CFG_CORTEXR=j7200_evm_r5_defconfig $ export UBOOT_CFG_CORTEXA=j7200_evm_a72_defconfig $ export TFA_BOARD=generic $ # we dont use any extra TFA parameters $ unset TFA_EXTRA_ARGS $ export OPTEE_PLATFORM=k3-j7200 $ # we dont use any extra OP-TEE parameters $ unset OPTEE_EXTRA_ARGS .. j7200_evm_rst_include_start_build_steps 1. Trusted Firmware-A: .. include:: k3.rst :start-after: .. k3_rst_include_start_build_steps_tfa :end-before: .. k3_rst_include_end_build_steps_tfa 2. OP-TEE: .. include:: k3.rst :start-after: .. k3_rst_include_start_build_steps_optee :end-before: .. k3_rst_include_end_build_steps_optee 3. U-Boot: * 4.1 R5: .. include:: k3.rst :start-after: .. k3_rst_include_start_build_steps_spl_r5 :end-before: .. k3_rst_include_end_build_steps_spl_r5 * 4.2 A72: .. include:: k3.rst :start-after: .. k3_rst_include_start_build_steps_uboot :end-before: .. k3_rst_include_end_build_steps_uboot .. j7200_evm_rst_include_end_build_steps Target Images -------------- In order to boot we need tiboot3.bin, tispl.bin and u-boot.img. Each SoC variant (GP, HS-FS, HS-SE) requires a different source for these files. - GP * tiboot3-j7200-gp-evm.bin from step 4.1 * tispl.bin_unsigned, u-boot.img_unsigned from step 4.2 - HS-FS * tiboot3-j7200_sr2-hs-fs-evm.bin from step 4.1 * tispl.bin, u-boot.img from step 4.2 - HS-SE * tiboot3-j7200_sr2-hs-evm.bin from step 4.1 * tispl.bin, u-boot.img from step 4.2 Image formats: -------------- - tiboot3.bin .. image:: img/j7200_tiboot3.bin.svg - tispl.bin .. image:: img/dm_tispl.bin.svg Switch Setting for Boot Mode ---------------------------- Boot Mode pins provide means to select the boot mode and options before the device is powered up. After every POR, they are the main source to populate the Boot Parameter Tables. The following table shows some common boot modes used on J7200 platform. More details can be found in the Technical Reference Manual: https://www.ti.com/lit/pdf/spruiu1 under the `Boot Mode Pins` section. .. list-table:: Boot Modes :widths: 16 16 16 :header-rows: 1 * - Switch Label - SW9: 12345678 - SW8: 12345678 * - SD - 00000000 - 10000010 * - EMMC - 01000000 - 10000000 * - OSPI - 01000000 - 00000110 * - UART - 01110000 - 00000000 * - USB DFU - 00100000 - 10000000 For SW8 and SW9, the switch state in the "ON" position = 1. eMMC: ----- ROM supports booting from eMMC raw read or UDA FS mode. Below is memory layout in case of booting from boot 0/1 partition in raw mode. Current allocated size for tiboot3 size is 1MB, tispl is 2MB. Size of u-boot.img is taken 4MB for refernece, But this is subject to change depending upon atf, optee size .. image:: img/emmc_j7200_evm_boot01.svg In case of UDA FS mode booting, following is layout. All boot images tiboot3.bin, tispl and u-boot should be written to fat formatted UDA FS as file. .. image:: img/emmc_j7200_evm_udafs.svg In case of booting from eMMC, write above images into raw or UDA FS. and set mmc partconf accordingly. Debugging U-Boot ---------------- See :ref:`Common Debugging environment - OpenOCD`: for detailed setup information. .. warning:: **OpenOCD support since**: v0.12.0 If the default package version of OpenOCD in your development environment's distribution needs to be updated, it might be necessary to build OpenOCD from the source. .. include:: k3.rst :start-after: .. k3_rst_include_start_openocd_connect_XDS110 :end-before: .. k3_rst_include_end_openocd_connect_XDS110 To start OpenOCD and connect to the board .. code-block:: bash openocd -f board/ti_j7200evm.cfg