menu "SPI Flash Support" config DM_SPI_FLASH bool "Enable Driver Model for SPI flash" depends on DM && DM_SPI imply SPI_FLASH help Enable driver model for SPI flash. This SPI flash interface (spi_flash_probe(), spi_flash_write(), etc.) is then implemented by the SPI flash uclass. There is one standard SPI flash driver which knows how to probe most chips supported by U-Boot. The uclass interface is defined in include/spi_flash.h, but is currently fully compatible with the old interface to avoid confusion and duplication during the transition parent. SPI and SPI flash must be enabled together (it is not possible to use driver model for one and not the other). config SPI_FLASH_SANDBOX bool "Support sandbox SPI flash device" depends on SANDBOX && DM_SPI_FLASH help Since sandbox cannot access real devices, an emulation mechanism is provided instead. Drivers can be connected up to the sandbox SPI bus (see CONFIG_SANDBOX_SPI) and SPI traffic will be routed to this device. Typically the contents of the emulated SPI flash device is stored in a file on the host filesystem. config SPI_FLASH bool "SPI Flash Core Interface support" select SPI_MEM help Enable the SPI flash Core support. This will include basic standard support for things like probing, read / write, and erasing through cmd_sf interface. If unsure, say N config SF_DEFAULT_BUS int "SPI Flash default bus identifier" depends on SPI_FLASH || DM_SPI_FLASH default 0 help The default bus may be provided by the platform to handle the common case when only a single serial flash is present on the system. config SF_DEFAULT_CS int "SPI Flash default Chip-select" depends on SPI_FLASH || DM_SPI_FLASH default 0 help The default chip select may be provided by the platform to handle the common case when only a single serial flash is present on the system. config SF_DEFAULT_MODE hex "SPI Flash default mode (see include/spi.h)" depends on SPI_FLASH || DM_SPI_FLASH default 0x0 help The default mode may be provided by the platform to handle the common case when only a single serial flash is present on the system. Not used for boot with device tree; the SPI driver reads speed and mode from plat values computed from available node. config SF_DEFAULT_SPEED int "SPI Flash default speed in Hz" depends on SPI_FLASH || DM_SPI_FLASH default 1000000 help The default speed may be provided by the platform to handle the common case when only a single serial flash is present on the system. Not used for boot with device tree; the SPI driver reads speed and mode from plat values computed from available node. if SPI_FLASH config SPI_FLASH_SFDP_SUPPORT bool "SFDP table parsing support for SPI NOR flashes" depends on !SPI_FLASH_BAR help Enable support for parsing and auto discovery of parameters for SPI NOR flashes using Serial Flash Discoverable Parameters (SFDP) tables as per JESD216 standard. config SPI_FLASH_SMART_HWCAPS bool "Smart hardware capability detection based on SPI MEM supports_op() hook" default y help Enable support for smart hardware capability detection based on SPI MEM supports_op() hook that lets controllers express whether they can support a type of operation in a much more refined way compared to using flags like SPI_RX_DUAL, SPI_TX_QUAD, etc. config SPI_NOR_BOOT_SOFT_RESET_EXT_INVERT bool "Command extension type is INVERT for Software Reset on boot" default n help Because of SFDP information can not be get before boot. So define command extension type is INVERT when Software Reset on boot only. config SPI_FLASH_SOFT_RESET bool "Software Reset support for SPI NOR flashes" help Enable support for xSPI Software Reset. It will be used to switch from Octal DTR mode to legacy mode on shutdown and boot (if enabled). config SPI_FLASH_SOFT_RESET_ON_BOOT bool "Perform a Software Reset on boot on flashes that boot in stateful mode" depends on SPI_FLASH_SOFT_RESET help Perform a Software Reset on boot to allow detecting flashes that are handed to us in Octal DTR mode. Do not enable this config on flashes that are not supposed to be handed to U-Boot in Octal DTR mode, even if they _do_ support the Soft Reset sequence. config SPI_FLASH_BAR bool "SPI flash Bank/Extended address register support" help Enable the SPI flash Bank/Extended address register support. Bank/Extended address registers are used to access the flash which has size > 16MiB in 3-byte addressing. config SPI_FLASH_UNLOCK_ALL bool "Unlock the entire SPI flash on u-boot startup" default y help Some flashes tend to power up with the software write protection bits set. If this option is set, the whole flash will be unlocked. For legacy reasons, this option default to y. But if you intend to actually use the software protection bits you should say n here. config SPI_FLASH_ATMEL bool "Atmel SPI flash support" help Add support for various Atmel SPI flash chips (AT45xxx and AT25xxx) config SPI_FLASH_EON bool "EON SPI flash support" help Add support for various EON SPI flash chips (EN25xxx) config SPI_FLASH_GIGADEVICE bool "GigaDevice SPI flash support" help Add support for various GigaDevice SPI flash chips (GD25xxx) config SPI_FLASH_ISSI bool "ISSI SPI flash support" help Add support for various ISSI SPI flash chips (ISxxx) config SPI_FLASH_MACRONIX bool "Macronix SPI flash support" help Add support for various Macronix SPI flash chips (MX25Lxxx) config SPI_FLASH_SPANSION bool "Spansion SPI flash support" help Add support for various Spansion SPI flash chips (S25FLxxx) config SPI_FLASH_S28HX_T bool "Cypress SEMPER Octal (S28) chip support" depends on SPI_FLASH_SPANSION help Add support for the Cypress S28HL-T and S28HS-T chip. This is a separate config because the fixup hooks for this flash add extra size overhead. Boards that don't use the flash can disable this to save space. config SPI_FLASH_STMICRO bool "STMicro SPI flash support" help Add support for various STMicro SPI flash chips (M25Pxxx and N25Qxxx) config SPI_FLASH_MT35XU bool "Micron MT35XU chip support" depends on SPI_FLASH_STMICRO help Add support for the Micron MT35XU chip. This is a separate config because the fixup hooks for this flash add extra size overhead. Boards that don't use the flash can disable this to save space. config SPI_FLASH_SST bool "SST SPI flash support" help Add support for various SST SPI flash chips (SST25xxx) config SPI_FLASH_WINBOND bool "Winbond SPI flash support" help Add support for various Winbond SPI flash chips (W25xxx) config SPI_FLASH_XMC bool "XMC SPI flash support" help Add support for various XMC (Wuhan Xinxin Semiconductor Manufacturing Corp.) SPI flash chips (XM25xxx) config SPI_FLASH_XTX bool "XTX SPI flash support" help Add support for various XTX (XTX Technology Limited) SPI flash chips (XT25xxx). endif config SPI_FLASH_USE_4K_SECTORS bool "Use small 4096 B erase sectors" depends on SPI_FLASH default y help Many flash memories support erasing small (4096 B) sectors. Depending on the usage this feature may provide performance gain in comparison to erasing whole blocks (32/64 KiB). Changing a small part of the flash's contents is usually faster with small sectors. On the other hand erasing should be faster when using 64 KiB block instead of 16 × 4 KiB sectors. Please note that some tools/drivers/filesystems may not work with 4096 B erase size (e.g. UBIFS requires 15 KiB as a minimum). config SPI_FLASH_DATAFLASH bool "AT45xxx DataFlash support" depends on SPI_FLASH && DM_SPI_FLASH help Enable the access for SPI-flash-based AT45xxx DataFlash chips. DataFlash is a kind of SPI flash. Most AT45 chips have two buffers in each chip, which may be used for double buffered I/O; but this driver doesn't (yet) use these for any kind of i/o overlap or prefetching. Sometimes DataFlash is packaged in MMC-format cards, although the MMC stack can't (yet?) distinguish between MMC and DataFlash protocols during enumeration. If unsure, say N config SPI_FLASH_MTD bool "SPI Flash MTD support" depends on SPI_FLASH && MTD help Enable the MTD support for spi flash layer, this adapter is for translating mtd_read/mtd_write commands into spi_flash_read/write commands. It is not intended to use it within sf_cmd or the SPI flash subsystem. Such an adapter is needed for subsystems like UBI which can only operate on top of the MTD layer. If unsure, say N config SPL_SPI_FLASH_MTD bool "SPI flash MTD support for SPL" depends on SPI_FLASH && SPL help Enable the MTD support for the SPI flash layer in SPL. If unsure, say N endmenu # menu "SPI Flash Support"