/* SPDX-License-Identifier: GPL-2.0+ */ /* * Copyright 2014 Freescale Semiconductor, Inc. * Copyright 2020-2023 NXP */ #ifndef __CONFIG_H #define __CONFIG_H #include /* * T104x RDB board configuration file */ #include #ifdef CONFIG_RAMBOOT_PBL #define RESET_VECTOR_OFFSET 0x27FFC #define BOOT_PAGE_OFFSET 0x27000 #ifdef CONFIG_MTD_RAW_NAND #ifdef CONFIG_NXP_ESBC #define CFG_SYS_NAND_U_BOOT_SIZE ((768 << 10) + (16 << 10)) #else #define CFG_SYS_NAND_U_BOOT_SIZE (768 << 10) #endif #define CFG_SYS_NAND_U_BOOT_DST 0x30000000 #define CFG_SYS_NAND_U_BOOT_START 0x30000000 #endif #ifdef CONFIG_SPIFLASH #define CFG_RESET_VECTOR_ADDRESS 0x30000FFC #define CFG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) #define CFG_SYS_SPI_FLASH_U_BOOT_DST (0x30000000) #define CFG_SYS_SPI_FLASH_U_BOOT_START (0x30000000) #define CFG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) #endif #ifdef CONFIG_SDCARD #define CFG_RESET_VECTOR_ADDRESS 0x30000FFC #define CFG_SYS_MMC_U_BOOT_SIZE (768 << 10) #define CFG_SYS_MMC_U_BOOT_DST (0x30000000) #define CFG_SYS_MMC_U_BOOT_START (0x30000000) #define CFG_SYS_MMC_U_BOOT_OFFS (260 << 10) #endif #endif /* High Level Configuration Options */ #ifndef CFG_RESET_VECTOR_ADDRESS #define CFG_RESET_VECTOR_ADDRESS 0xeffffffc #endif #define CFG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS /* * These can be toggled for performance analysis, otherwise use default. */ #define CFG_SYS_INIT_L2CSR0 L2CSR0_L2E /* * Config the L3 Cache as L3 SRAM */ #define CFG_SYS_INIT_L3_ADDR 0xFFFC0000 /* * For Secure Boot CFG_SYS_INIT_L3_ADDR will be redefined and hence * Physical address (CFG_SYS_INIT_L3_ADDR) and virtual address * (CFG_SYS_INIT_L3_VADDR) will be different. */ #define CFG_SYS_INIT_L3_VADDR 0xFFFC0000 #define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) #define CFG_SYS_DCSRBAR 0xf0000000 #define CFG_SYS_DCSRBAR_PHYS 0xf00000000ull /* * DDR Setup */ #define CFG_SYS_DDR_SDRAM_BASE 0x00000000 #define CFG_SYS_SDRAM_BASE CFG_SYS_DDR_SDRAM_BASE #define SPD_EEPROM_ADDRESS 0x51 #define CFG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ /* * IFC Definitions */ #define CFG_SYS_FLASH_BASE 0xe8000000 #define CFG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CFG_SYS_FLASH_BASE) #define CFG_SYS_NOR_CSPR_EXT (0xf) #define CFG_SYS_NOR_CSPR (CSPR_PHYS_ADDR(CFG_SYS_FLASH_BASE) | \ CSPR_PORT_SIZE_16 | \ CSPR_MSEL_NOR | \ CSPR_V) #define CFG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) /* * TDM Definition */ #define T1040_TDM_QUIRK_CCSR_BASE 0xfe000000 /* NOR Flash Timing Params */ #define CFG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 #define CFG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ FTIM0_NOR_TEADC(0x5) | \ FTIM0_NOR_TEAHC(0x5)) #define CFG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ FTIM1_NOR_TRAD_NOR(0x1A) |\ FTIM1_NOR_TSEQRAD_NOR(0x13)) #define CFG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ FTIM2_NOR_TCH(0x4) | \ FTIM2_NOR_TWPH(0x0E) | \ FTIM2_NOR_TWP(0x1c)) #define CFG_SYS_NOR_FTIM3 0x0 #define CFG_SYS_FLASH_BANKS_LIST {CFG_SYS_FLASH_BASE_PHYS} /* CPLD on IFC */ #define CPLD_LBMAP_MASK 0x3F #define CPLD_BANK_SEL_MASK 0x07 #define CPLD_BANK_OVERRIDE 0x40 #define CPLD_LBMAP_ALTBANK 0x44 /* BANK OR | BANK 4 */ #define CPLD_LBMAP_DFLTBANK 0x40 /* BANK OR | BANK0 */ #define CPLD_LBMAP_RESET 0xFF #define CPLD_LBMAP_SHIFT 0x03 #if defined(CONFIG_TARGET_T1042D4RDB) #define CPLD_DIU_SEL_DFP 0xc0 #endif #define CFG_SYS_CPLD_BASE 0xffdf0000 #define CFG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CFG_SYS_CPLD_BASE) #define CFG_SYS_CSPR2_EXT (0xf) #define CFG_SYS_CSPR2 (CSPR_PHYS_ADDR(CFG_SYS_CPLD_BASE_PHYS) \ | CSPR_PORT_SIZE_8 \ | CSPR_MSEL_GPCM \ | CSPR_V) #define CFG_SYS_AMASK2 IFC_AMASK(64*1024) #define CFG_SYS_CSOR2 0x0 /* CPLD Timing parameters for IFC CS2 */ #define CFG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ FTIM0_GPCM_TEADC(0x0e) | \ FTIM0_GPCM_TEAHC(0x0e)) #define CFG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ FTIM1_GPCM_TRAD(0x1f)) #define CFG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ FTIM2_GPCM_TCH(0x8) | \ FTIM2_GPCM_TWP(0x1f)) #define CFG_SYS_CS2_FTIM3 0x0 /* NAND Flash on IFC */ #define CFG_SYS_NAND_BASE 0xff800000 #define CFG_SYS_NAND_BASE_PHYS (0xf00000000ull | CFG_SYS_NAND_BASE) #define CFG_SYS_NAND_CSPR_EXT (0xf) #define CFG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CFG_SYS_NAND_BASE_PHYS) \ | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ | CSPR_MSEL_NAND /* MSEL = NAND */ \ | CSPR_V) #define CFG_SYS_NAND_AMASK IFC_AMASK(64*1024) #define CFG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ | CSOR_NAND_PGS_4K /* Page Size = 4K */ \ | CSOR_NAND_SPRZ_224/* Spare size = 224 */ \ | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ /* ONFI NAND Flash mode0 Timing Params */ #define CFG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ FTIM0_NAND_TWP(0x18) | \ FTIM0_NAND_TWCHT(0x07) | \ FTIM0_NAND_TWH(0x0a)) #define CFG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ FTIM1_NAND_TWBE(0x39) | \ FTIM1_NAND_TRR(0x0e) | \ FTIM1_NAND_TRP(0x18)) #define CFG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ FTIM2_NAND_TREH(0x0a) | \ FTIM2_NAND_TWHRE(0x1e)) #define CFG_SYS_NAND_FTIM3 0x0 #define CFG_SYS_NAND_BASE_LIST { CFG_SYS_NAND_BASE } #if defined(CONFIG_MTD_RAW_NAND) #define CFG_SYS_CSPR0_EXT CFG_SYS_NAND_CSPR_EXT #define CFG_SYS_CSPR0 CFG_SYS_NAND_CSPR #define CFG_SYS_AMASK0 CFG_SYS_NAND_AMASK #define CFG_SYS_CSOR0 CFG_SYS_NAND_CSOR #define CFG_SYS_CS0_FTIM0 CFG_SYS_NAND_FTIM0 #define CFG_SYS_CS0_FTIM1 CFG_SYS_NAND_FTIM1 #define CFG_SYS_CS0_FTIM2 CFG_SYS_NAND_FTIM2 #define CFG_SYS_CS0_FTIM3 CFG_SYS_NAND_FTIM3 #define CFG_SYS_CSPR1_EXT CFG_SYS_NOR_CSPR_EXT #define CFG_SYS_CSPR1 CFG_SYS_NOR_CSPR #define CFG_SYS_AMASK1 CFG_SYS_NOR_AMASK #define CFG_SYS_CSOR1 CFG_SYS_NOR_CSOR #define CFG_SYS_CS1_FTIM0 CFG_SYS_NOR_FTIM0 #define CFG_SYS_CS1_FTIM1 CFG_SYS_NOR_FTIM1 #define CFG_SYS_CS1_FTIM2 CFG_SYS_NOR_FTIM2 #define CFG_SYS_CS1_FTIM3 CFG_SYS_NOR_FTIM3 #else #define CFG_SYS_CSPR0_EXT CFG_SYS_NOR_CSPR_EXT #define CFG_SYS_CSPR0 CFG_SYS_NOR_CSPR #define CFG_SYS_AMASK0 CFG_SYS_NOR_AMASK #define CFG_SYS_CSOR0 CFG_SYS_NOR_CSOR #define CFG_SYS_CS0_FTIM0 CFG_SYS_NOR_FTIM0 #define CFG_SYS_CS0_FTIM1 CFG_SYS_NOR_FTIM1 #define CFG_SYS_CS0_FTIM2 CFG_SYS_NOR_FTIM2 #define CFG_SYS_CS0_FTIM3 CFG_SYS_NOR_FTIM3 #define CFG_SYS_CSPR1_EXT CFG_SYS_NAND_CSPR_EXT #define CFG_SYS_CSPR1 CFG_SYS_NAND_CSPR #define CFG_SYS_AMASK1 CFG_SYS_NAND_AMASK #define CFG_SYS_CSOR1 CFG_SYS_NAND_CSOR #define CFG_SYS_CS1_FTIM0 CFG_SYS_NAND_FTIM0 #define CFG_SYS_CS1_FTIM1 CFG_SYS_NAND_FTIM1 #define CFG_SYS_CS1_FTIM2 CFG_SYS_NAND_FTIM2 #define CFG_SYS_CS1_FTIM3 CFG_SYS_NAND_FTIM3 #endif /* define to use L1 as initial stack */ #define CFG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ #define CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf #define CFG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 /* The assembler doesn't like typecast */ #define CFG_SYS_INIT_RAM_ADDR_PHYS \ ((CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ CFG_SYS_INIT_RAM_ADDR_PHYS_LOW) #define CFG_SYS_INIT_RAM_SIZE 0x00004000 #define CFG_SYS_INIT_SP_OFFSET (CFG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) /* Serial Port - controlled on board with jumper J8 * open - index 2 * shorted - index 1 */ #if !CONFIG_IS_ENABLED(DM_SERIAL) #define CFG_SYS_NS16550_CLK (get_bus_freq(0)/2) #endif #define CFG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} #define CFG_SYS_NS16550_COM1 (CFG_SYS_CCSRBAR+0x11C500) #define CFG_SYS_NS16550_COM2 (CFG_SYS_CCSRBAR+0x11C600) #define CFG_SYS_NS16550_COM3 (CFG_SYS_CCSRBAR+0x11D500) #define CFG_SYS_NS16550_COM4 (CFG_SYS_CCSRBAR+0x11D600) /* I2C bus multiplexer */ #define I2C_MUX_PCA_ADDR 0x70 #define I2C_MUX_CH_DEFAULT 0x8 #if defined(CONFIG_TARGET_T1042D4RDB) /* * RTC configuration */ #define CFG_SYS_I2C_RTC_ADDR 0x68 #endif /* * eSPI - Enhanced SPI */ /* * General PCI * Memory space is mapped 1-1, but I/O space must start from 0. */ #ifdef CONFIG_PCI /* controller 1, direct to uli, tgtid 3, Base address 20000 */ #ifdef CONFIG_PCIE1 #define CFG_SYS_PCIE1_MEM_VIRT 0x80000000 #define CFG_SYS_PCIE1_MEM_PHYS 0xc00000000ull #define CFG_SYS_PCIE1_IO_VIRT 0xf8000000 #define CFG_SYS_PCIE1_IO_PHYS 0xff8000000ull #endif /* controller 2, Slot 2, tgtid 2, Base address 201000 */ #ifdef CONFIG_PCIE2 #define CFG_SYS_PCIE2_MEM_VIRT 0x90000000 #define CFG_SYS_PCIE2_MEM_PHYS 0xc10000000ull #define CFG_SYS_PCIE2_IO_VIRT 0xf8010000 #define CFG_SYS_PCIE2_IO_PHYS 0xff8010000ull #endif /* controller 3, Slot 1, tgtid 1, Base address 202000 */ #ifdef CONFIG_PCIE3 #define CFG_SYS_PCIE3_MEM_VIRT 0xa0000000 #define CFG_SYS_PCIE3_MEM_PHYS 0xc20000000ull #endif /* controller 4, Base address 203000 */ #ifdef CONFIG_PCIE4 #define CFG_SYS_PCIE4_MEM_VIRT 0xb0000000 #define CFG_SYS_PCIE4_MEM_PHYS 0xc30000000ull #endif #endif /* CONFIG_PCI */ /* * USB */ #ifdef CONFIG_MMC #define CFG_SYS_FSL_ESDHC_ADDR CFG_SYS_MPC85xx_ESDHC_ADDR #endif /* Qman/Bman */ #ifndef CONFIG_NOBQFMAN #define CFG_SYS_BMAN_NUM_PORTALS 10 #define CFG_SYS_BMAN_MEM_BASE 0xf4000000 #define CFG_SYS_BMAN_MEM_PHYS 0xff4000000ull #define CFG_SYS_BMAN_MEM_SIZE 0x02000000 #define CFG_SYS_BMAN_SP_CENA_SIZE 0x4000 #define CFG_SYS_BMAN_SP_CINH_SIZE 0x1000 #define CFG_SYS_BMAN_CENA_BASE CFG_SYS_BMAN_MEM_BASE #define CFG_SYS_BMAN_CENA_SIZE (CFG_SYS_BMAN_MEM_SIZE >> 1) #define CFG_SYS_BMAN_CINH_BASE (CFG_SYS_BMAN_MEM_BASE + \ CFG_SYS_BMAN_CENA_SIZE) #define CFG_SYS_BMAN_CINH_SIZE (CFG_SYS_BMAN_MEM_SIZE >> 1) #define CFG_SYS_BMAN_SWP_ISDR_REG 0xE08 #define CFG_SYS_QMAN_NUM_PORTALS 10 #define CFG_SYS_QMAN_MEM_BASE 0xf6000000 #define CFG_SYS_QMAN_MEM_PHYS 0xff6000000ull #define CFG_SYS_QMAN_MEM_SIZE 0x02000000 #define CFG_SYS_QMAN_SP_CINH_SIZE 0x1000 #define CFG_SYS_QMAN_CENA_SIZE (CFG_SYS_QMAN_MEM_SIZE >> 1) #define CFG_SYS_QMAN_CINH_BASE (CFG_SYS_QMAN_MEM_BASE + \ CFG_SYS_QMAN_CENA_SIZE) #define CFG_SYS_QMAN_CINH_SIZE (CFG_SYS_QMAN_MEM_SIZE >> 1) #define CFG_SYS_QMAN_SWP_ISDR_REG 0xE08 #endif /* CONFIG_NOBQFMAN */ #ifdef CONFIG_FMAN_ENET #if defined(CONFIG_TARGET_T1042D4RDB) #define CFG_SYS_SGMII1_PHY_ADDR 0x02 #define CFG_SYS_SGMII2_PHY_ADDR 0x03 #define CFG_SYS_SGMII3_PHY_ADDR 0x01 #endif #define CFG_SYS_RGMII1_PHY_ADDR 0x01 #define CFG_SYS_RGMII2_PHY_ADDR 0x02 #endif /* * Miscellaneous configurable options */ /* * For booting Linux, the board info and command line data * have to be in the first 64 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CFG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ /* * Dynamic MTD Partition support with mtdparts */ /* * Environment Configuration */ #define __USB_PHY_TYPE utmi #define RAMDISKFILE "t104xrdb/ramdisk.uboot" #if defined(CONFIG_TARGET_T1042D4RDB) #define FDTFILE "t1042rdb/t1042d4rdb.dtb" #endif #define CFG_EXTRA_ENV_SETTINGS \ "hwconfig=fsl_ddr:bank_intlv=cs0_cs1;" \ "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\ "usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ "netdev=eth0\0" \ "uboot=" CONFIG_UBOOTPATH "\0" \ "ubootaddr=" __stringify(CONFIG_TEXT_BASE) "\0" \ "tftpflash=tftpboot $loadaddr $uboot && " \ "protect off $ubootaddr +$filesize && " \ "erase $ubootaddr +$filesize && " \ "cp.b $loadaddr $ubootaddr $filesize && " \ "protect on $ubootaddr +$filesize && " \ "cmp.b $loadaddr $ubootaddr $filesize\0" \ "consoledev=ttyS0\0" \ "ramdiskaddr=2000000\0" \ "ramdiskfile=" __stringify(RAMDISKFILE) "\0" \ "fdtaddr=1e00000\0" \ "fdtfile=" __stringify(FDTFILE) "\0" \ "bdev=sda3\0" #include #endif /* __CONFIG_H */